oSIST prEN ISO 16276-1:2024

Corrosion protection of steel structures by protective paint systems - Assessment of, and acceptance criteria for, the adhesion/cohesion (fracture strength) of a coating - Part 1: Pull-off testing (ISO/DIS 16276-1:2024)

ISO 16276-1:2007 specifies procedures for assessing the fracture strength of a protective paint coating of any thickness on a steel substrate of thickness not less than 10 mm. The procedures given in this part of ISO 16276 are based on methods used with different types of pull-off test equipment. The results obtained using such different types of equipment are not comparable.
This part of ISO 16276 also specifies suitable equipment and defines inspection areas, sampling plans and acceptance/rejection criteria.
It does not give any values of the fracture strength of different protective paint coatings.

Korrosionsschutz von Stahlbauten durch Beschichtungssysteme - Beurteilung der Adhäsion/Kohäsion (Haftfestigkeit) einer Beschichtung und Kriterien für deren Annahme - Teil1: Abreißversuch (ISO/DIS 16276-1:2024)

Dieser Teil von ISO 16276 legt Verfahren zum Bewerten der Haftfestigkeit eines Beschichtungssystems beliebiger Schichtdicke auf einem mindestens 10 mm dicken Stahlsubstrat fest. Die in diesem Teil von ISO 16276 angegebenen Verfahren basieren auf Prüfverfahren für unterschiedliche Typen von Abreißprüfgeräten. Die mit unterschiedlichen Typen von Abreißprüfgeräten erhaltenen Ergebnisse sind nicht zu vergleichen.
ANMERKUNG 1   Substrate mit weniger als 10 mm Dicke können geprüft werden, wenn sie durch die Sandwich Technik (siehe ISO 4624) oder die Art  des Bauteiles (z. B. Doppel T Träger, Grundplatte) verstärkt werden. Ansonsten können Probenplatten mit mindestens 10 mm Dicke verwendet werden, die gleichzeitig mit dem Bauwerk beschichtet wurden, oder es wird nach ISO 16276 2 geprüft.
Dieser Teil von ISO 16276 ist nur anwendbar, wenn ein Wert für die Haftfestigkeit zusammen mit Typ und Hersteller des Gerätes festgelegt wird. Üblicherweise sind diese Angaben in den Vertragsunterlagen enthalten.
ANMERKUNG 2   Ein Wert für die Haftfestigkeit ist nur aussagefähig, wenn die Anforderungen an die Umgebungsbedingungen (siehe 6.4.2) eingehalten werden.
Dieser Teil von ISO 16276 legt die Anwendung geeigneter Geräte fest und definiert Inspektionsflächen, Messpläne sowie Kriterien für die Annahme/Ablehnung.
Er gibt keine Werte für die Haftfestigkeit von verschiedenen Beschichtungssystemen an.

Protection contre la corrosion des structures en acier par systèmes de peinture - Évaluation et critères d’acceptation de l’adhésion/cohésion (résistance à la rupture) d’un revêtement - Partie 1: Essai d’arrachement par traction (ISO/DIS 16276-1:2024)

L'ISO 16276-1:2007 spécifie des modes opératoires permettant d'évaluer la résistance à la rupture d'un système de peinture, quelle que soit son épaisseur, appliqué sur un subjectile en acier ayant une épaisseur au moins égale à 10 mm. Les modes opératoires figurant dans l'ISO 16276-1:2007 reposent sur des méthodes d'essai utilisant différents types de machines d'essai de traction. Les résultats obtenus sur ces différents types d'appareils d'essai ne sont pas comparables.
L'ISO 16276-1:2007 spécifie l'utilisation d'appareillages appropriés et définit les aires de contrôle, les plans d'échantillonnage et les critères d'acceptation/de rejet.
Elle ne donne aucune valeur de résistance à la rupture pour les différents systèmes de peinture.

Protikorozijska zaščita jeklenih konstrukcij z zaščitnimi premaznimi sistemi - Ocenjevanje adhezije/kohezije (lomne trdnosti) premazov in kriteriji sprejemljivosti - 1. del: Preskus odtrganja (pull-off testing) (ISO/DIS 16276-1:2024)

General Information

• Status: Not Published
• Public Enquiry End Date: 01-Aug-2024
• ICS: 25.220.20 - Surface treatment
• ICS: 87.020 - Paint coating processes
• ICS: 87.040 - Paints and varnishes
• ICS: 91.080.13 - Steel structures
• Technical Committee: IBLP - Paints and varnishes
• Current Stage: 4020 - Public enquire (PE) (Adopted Project)
• Start Date: 29-May-2024
• Due Date: 16-Oct-2024
• Ref Project: prEN ISO 16276-1 - Corrosion protection of steel structures by protective paint systems - Assessment of, and acceptance criteria for, the adhesion/cohesion (fracture strength) of a coating - Part 1: Pull-off testing (ISO/DIS 16276-1:2024)

Relations

• Revises: SIST EN ISO 16276-1:2009 - Corrosion protection of steel structures by protective paint systems - Assessment of, and acceptance criteria for, the adhesion/cohesion (fracture strength) of a coating - Part 1: Pull-off testing (ISO 16276-1:2007)
• Effective Date: 01-Jun-2024

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN ISO 16276-1:2024
01-julij-2024
Protikorozijska zaščita jeklenih konstrukcij z zaščitnimi premaznimi sistemi -
Ocenjevanje adhezije/kohezije (lomne trdnosti) premazov in kriteriji sprejemljivosti
- 1. del: Preskus odtrganja (pull-off testing) (ISO/DIS 16276-1:2024)
Corrosion protection of steel structures by protective paint systems - Assessment of, and
acceptance criteria for, the adhesion/cohesion (fracture strength) of a coating - Part 1:
Pull-off testing (ISO/DIS 16276-1:2024)
Korrosionsschutz von Stahlbauten durch Beschichtungssysteme - Beurteilung der
Adhäsion/Kohäsion (Haftfestigkeit) einer Beschichtung und Kriterien für deren Annahme
- Teil1: Abreißversuch (ISO/DIS 16276-1:2024)
Protection contre la corrosion des structures en acier par systèmes de peinture -
Évaluation et critères d’acceptation de l’adhésion/cohésion (résistance à la rupture) d’un
revêtement - Partie 1: Essai d’arrachement par traction (ISO/DIS 16276-1:2024)
Ta slovenski standard je istoveten z: prEN ISO 16276-1
ICS:
25.220.20 Površinska obdelava Surface treatment
87.040 Barve in laki Paints and varnishes
91.080.13 Jeklene konstrukcije Steel structures
oSIST prEN ISO 16276-1:2024 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN ISO 16276-1:2024

---------------------- Page: 2 ----------------------
oSIST prEN ISO 16276-1:2024
DRAFT
International
Standard
ISO/DIS 16276-1
ISO/TC 35/SC 14
Corrosion protection of steel
Secretariat: DIN
structures by protective paint
Voting begins on:
systems — Assessment of, and
2024-05-16
acceptance criteria for, the
Voting terminates on:
adhesion/cohesion (fracture
2024-08-08
strength) of a coating —
Part 1:
Pull-off testing
Anticorrosion des structures en acier par systèmes de peinture —
Évaluation et critères d'acceptation de l'adhésion/cohésion
(résistance à la rupture) d'un revêtement —
Partie 1: Essai de traction
ICS: 87.020
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document is circulated as received from the committee secretariat.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS.
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Reference number
ISO/DIS 16276-1:2024(en)
© ISO 2024

---------------------- Page: 3 ----------------------
oSIST prEN ISO 16276-1:2024
DRAFT
ISO/DIS 16276-1:2024(en)
International
Standard
ISO/DIS 16276-1
ISO/TC 35/SC 14
Corrosion protection of steel
Secretariat: DIN
structures by protective paint
Voting begins on:
systems — Assessment of, and
acceptance criteria for, the
Voting terminates on:
adhesion/cohesion (fracture
strength) of a coating —
Part 1:
Pull-off testing
Anticorrosion des structures en acier par systèmes de peinture —
Évaluation et critères d'acceptation de l'adhésion/cohésion
(résistance à la rupture) d'un revêtement —
Partie 1: Essai de traction
ICS: 87.020
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document is circulated as received from the committee secretariat.
COPYRIGHT PROTECTED DOCUMENT
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
© ISO 2024
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
BE CONSIDERED IN THE LIGHT OF THEIR
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
or ISO’s member body in the country of the requester.
NATIONAL REGULATIONS.
ISO copyright office
RECIPIENTS OF THIS DRAFT ARE INVITED
CP 401 • Ch. de Blandonnet 8
TO SUBMIT, WITH THEIR COMMENTS,
CH-1214 Vernier, Geneva
NOTIFICATION OF ANY RELEVANT PATENT
Phone: [phone]
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Email: [e-mail]
Website: www.iso.org
Published in Switzerland Reference number
ISO/DIS 16276-1:2024(en)
© ISO 2024

...