Switches for household and similar fixed electrical installations - Part 2-5: Switches and related accessories for use in home and building electronic systems (HBES) (IEC 60669-2-5:2013 , modified)

This part of IEC 60669 applies to HBES switches with a working voltage not exceeding 250 V
a.c. and a rated current up to and including 16 A for household and similar fixed electrical
installations either indoors or outdoors and to associated electronic extension units.
It applies to:
– HBES switches for the operation of lamp circuits and the control of the brightness of lamps
(dimmers) as well as the control of the speed of motors (e.g. those used in ventilating
fans) and for other purposes (e.g. heating installations);
– sensors, actuators, switched-socket-outlets, associated electronic extension units, etc.
In the present standard the word "HBES switch" is applied to describe all kinds of HBES
devices e.g. switches, sensors, actuators, switched-socket-outlets, associated electronic
extension units, etc.
The operation and control are performed:
– intentionally by a person via an actuating member, a key, a card, etc., via a sensing
surface or a sensing unit, by means of touch, proximity, turn, optical, acoustic, thermal;
– by physical means, e.g. light, temperature, humidity, time, wind velocity, presence of
people;
– by any other influence;
and transmitted:
– by an electronic signal via several media, e.g. powerline (mains), twisted pair, optical
fibre, radio frequency, infra-red, etc.
HBES switches complying with this standard are suitable for use at ambient temperatures not
normally exceeding 25 °C, but occasionally reaching 35 °C.
This part of IEC 60669also applies to mounting boxes for HBES switches, with the exception
of those for flush-type HBES switches which are covered by IEC 60670-1.
NOTE 1 In the following country flush mounted boxes are covered by both EN 60670-1 and BS 4662: UK
Functional safety aspects of HBES switches are not covered by this standard. Functional
safety requirements are covered by the standards of the devices which are controlled by the
HBES.
In locations where special conditions prevail, e.g. higher temperature, special constructions
may be required.
NOTE 2 This standard is not intended to cover devices falling within the scope of IEC 60730.
NOTE 3 Within this Part 2-5, for any reference to IEC 60669-2-1 and its Amendment 1:2008, the term “electronic
switches” is replaced by “HBES switches”.
NOTE 4 In the following country, HBES switches complying with this standard are suitable for use at ambient
temperatures not normally exceeding 35 °C, but occasionally reaching 40 °C: CN.

Schalter für Haushalt und ähnliche ortsfeste elektrische Installationen - Teil 2-5: Besondere Anforderungen - Schalter und ähnliches Installationsmaterial zur Verwendung in elektronischer Systemtechnik für Heim und Gebäude (ESHG) (IEC 60669-2-5:2013 , modifiziert)

Interrupteurs pour installations électriques fixes domestiques et analogues - Partie 2-5: Prescriptions particulières - Interrupteurs et appareils associés pour usage dans les systèmes électroniques des foyers domestiques et bâtiments (HBES) (IEC 60669-2-5:2013 , modifiée)

La CEI 60669-2-5:2013 s'applique aux interrupteurs HBES de tension locale ne dépassant pas 250 V en courant alternatif et de courant assigné inférieur ou égal à 16 A, pour installations électriques fixes domestiques et analogues intérieures ou extérieures et pour les éléments électroniques périphériques.

Stikala za gospodinjstva in podobne nepremične električne inštalacije - 2-5. del: Stikala in pripadajoči pribor za uporabo elektronskih sistemov v stanovanjih in stavbah (IEC 60669-2-5:2013, spremenjen)

Ta del standarda IEC 60669 se uporablja za stikala za uporabo elektronskih sistemov v stanovanjih in stavbah z delovno izmenično napetostjo največ 250 V ter nazivnim tokom največ 16 A, ki se uporabljajo za upravljanje električnih inštalacij v gospodinjstvih in podobnih notranjih ali zunanjih nepremičnih električnih inštalacij, ter za sorodne elektronske razširitvene enote.
Uporablja se za:
– stikala za uporabo elektronskih sistemov v stanovanjih in stavbah za upravljanje tokokrogov s sijalkami in nadzor svetlosti sijalk (temnilna stikala), nadzor hitrosti motorjev (npr. motorjev, ki se uporabljajo za ventilatorje) ter druge namene (npr. ogrevalne inštalacije);
– senzorje, prožila, stikalne vtičnice, sorodne elektronske razširitvene enote itd. V tem standardu se izraz »stikalo za uporabo elektronskih sistemov v stanovanjih in stavbah« uporablja za opis vseh vrst naprav za uporabo elektronskih sistemov v stanovanjih in stavbah, npr. stikal, senzorjev, prožil, stikalnih vtičnic, sorodnih elektronskih razširitvenih enot itd.
Upravljanje in nadzor se izvajata:
– namensko, pri čemer ju izvaja oseba prek sprožilnega elementa, ključa, kartice itd. oziroma prek površine ali enote za zaznavanje dotika, bližine, obrata ali optičnih, akustičnih ali termičnih površin ali enot za zaznavanje;
– s fizikalnimi sredstvi, npr. svetlobo, temperaturo, vlažnostjo, hitrostjo vetra, prisotnostjo oseb;
– z drugimi sredstvi;
ter se prenaša:
– z elektronskim signalom prek različnih medijev, npr. napajalnih vodov, paric, optičnih vlaken, radijskih frekvenc, infrardečih žarkov itd.
Stikala za uporabo elektronskih sistemov v stanovanjih in stavbah, ki so skladna s tem standardom, so primerna za uporabo pri temperaturah okolja, ki običajno ne presegajo 25 °C, vendar občasno dosežejo 35 °C.
Ta del standarda IEC 60669 se uporablja tudi za montažne doze za stikala za uporabo elektronskih sistemov v stanovanjih in stavbah z izjemo montažnih doz za podometna stikala, ki so zajete v standardu IEC 60670-1.
OPOMBA 1: V naslednji državi so podometne montažne doze zajete v standardih EN 60670-1 in BS 4662: Združeno kraljestvo
Vidiki funkcionalne varnosti stikal za uporabo elektronskih sistemov v stanovanjih in stavbah niso zajeti v tem standardu. Zahteve za funkcionalno varnost so zajete v standardih za naprave, ki se upravljajo s stikali za uporabo elektronskih sistemov v stanovanjih in stavbah.
Na mestih, kjer prevladujejo posebni pogoji, npr. višja temperatura, so morda potrebne posebne konstrukcije.
OPOMBA 2: Ta standard ne zajema naprav, ki so zajete v standardu IEC 60730.
OPOMBA 3: V delih 2–5 je za vse sklice na standard IEC 60669-2-1 in njegovo dopolnilo 1:2008 izraz »elektronska stikala« zamenjan z izrazom »stikala za uporabo elektronskih sistemov v stanovanjih in stavbah«.
OPOMBA 4: V naslednji državi so stikala za uporabo elektronskih sistemov v stanovanjih in stavbah, ki so skladna s tem standardom, primerna za uporabo pri temperaturah okolja, ki običajno ne presegajo 35 °C, vendar občasno dosežejo 40 °C: Kitajska.

General Information

Status
Published
Publication Date
15-Dec-2016
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
04-Oct-2016
Due Date
09-Dec-2016
Completion Date
16-Dec-2016

RELATIONS

Buy Standard

Standard
SIST EN 60669-2-5:2017 - BARVE na PDF-str 49,50,51,52,53,54,55
English language
54 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day

Standards Content (sample)

SLOVENSKI STANDARD
SIST EN 60669-2-5:2017
01-februar-2017
1DGRPHãþD
SIST EN 50428:2006/A1:2007
SIST EN 50428:2006/A2:2009

6WLNDOD]DJRVSRGLQMVWYDLQSRGREQHQHSUHPLþQHHOHNWULþQHLQãWDODFLMHGHO

6WLNDODLQSULSDGDMRþLSULERU]DXSRUDERHOHNWURQVNLKVLVWHPRYYVWDQRYDQMLKLQ
VWDYEDK ,(&VSUHPHQMHQ

Switches for household and similar fixed electrical installations - Part 2-5: Switches and

related accessories for use in home and building electronic systems (HBES) (IEC 60669-

2-5:2013 , modified)

Schalter für Haushalt und ähnliche ortsfeste elektrische Installationen - Teil 2-5:

Besondere Anforderungen - Schalter und ähnliches Installationsmaterial zur Verwendung

in elektronischer Systemtechnik für Heim und Gebäude (ESHG) (IEC 60669-2-5:2013 ,

modifiziert)

Interrupteurs pour installations électriques fixes domestiques et analogues - Partie 2-5:

Prescriptions particulières - Interrupteurs et appareils associés pour usage dans les

systèmes électroniques des foyers domestiques et bâtiments (HBES) (IEC 60669-2-
5:2013 , modifiée)
Ta slovenski standard je istoveten z: EN 60669-2-5:2016
ICS:
29.120.40 Stikala Switches
97.120 Avtomatske krmilne naprave Automatic controls for
za dom household use
SIST EN 60669-2-5:2017 en

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 60669-2-5:2017
---------------------- Page: 2 ----------------------
SIST EN 60669-2-5:2017
EUROPEAN STANDARD EN 60669-2-5
NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2016
ICS 29.120.40 Supersedes EN 50428:2005
English Version
Switches for household and similar fixed electrical installations -
Part 2-5: Particular requirements - Switches and related
accessories for use in home and building electronic systems
(HBES)
(IEC 60669-2-5:2013 , modified)

Interrupteurs pour installations électriques fixes Schalter für Haushalt und ähnliche ortsfeste elektrische

domestiques et analogues - Partie 2-5: Prescriptions Installationen - Teil 2-5: Besondere Anforderungen -

particulières - Interrupteurs et appareils associés pour Schalter und ähnliches Installationsmaterial zur

usage dans les systèmes électroniques des foyers Verwendung in elektronischer Systemtechnik für Heim und

domestiques et bâtiments (HBES) Gebäude (ESHG)
(IEC 60669-2-5:2013 , modifiée) (IEC 60669-2-5:2013 , modifiziert)

This European Standard was approved by CENELEC on 2015-08-31. CENELEC members are bound to comply with the CEN/CENELEC

Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC

Management Centre or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation

under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the

same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,

Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,

Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,

Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels

© 2016 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.

Ref. No. EN 60669-2-5:2016 E
---------------------- Page: 3 ----------------------
SIST EN 60669-2-5:2017
EN 60669-2-5:2016
European foreword

The text of document 23B/1110/FDIS, future edition 1 of IEC 60669-2-5, prepared by SC 23B "Plugs,

socket-outlets and switches", of IEC/TC 23 "Electrical accessories" was submitted to the IEC-

CENELEC parallel vote and approved by CENELEC as EN 60669-2-5:2016.

A draft amendment, which covers common modifications to IEC 60669-2-5:2013 (23B/1110/FDIS),

was prepared by CLC/TC 23BX "Switches, boxes and enclosures for household and similar purposes,

plugs and socket outlets for d.c. and for the charging of electrical vehicles including their connectors"

and approved by CENELEC.
The following dates are fixed:
• latest date by which the document has to be implemented at
(dop) 2017-03-23
national level by publication of an identical national
standard or by endorsement
• latest date by which the national standards conflicting with
(dow) 2020-08-31
the document have to be withdrawn
This document supersedes EN 50428:2005.

This standard has to be used in conjunction with EN 60669-1:1999 and EN 60669-2-1:2004 and their

amendments. It lists the additional changes necessary to convert it into the European Standard:

"Switches for household and similar fixed electrical installations - Collateral standard - Switches and

related accessories for use in home and building electronic systems (HBES)".

When this standard states "addition", "modification" or "replacement", the relevant text of

EN 60669-1:1999 or EN 60669-2-1:2004 and their amendments (hereinafter called Part 1 and Part 2-1

respectively) is to be adapted accordingly.
NOTE The following numbering system is used:

- subclauses, tables and figures that are numbered starting from 201 are additional to those in Part 2-1;

- additional annexes to Part 1 are lettered AA, BB, etc.

Clauses, subclauses, notes, tables, figures and annexes which are additional to those in IEC 60669-2-5:2013 are

prefixed “Z”.

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such

patent rights.

This document has been prepared under a mandate given to CENELEC by the European Commission

and the European Free Trade Association, and supports essential requirements of EU Directive(s).

For the relationship with EU Directive(s), see informative Annexes ZZA, ZZB and ZZC, which are

integral parts of this document.
---------------------- Page: 4 ----------------------
SIST EN 60669-2-5:2017
EN 60669-2-5:2016
Endorsement notice

The text of the International Standard IEC 60669-2-5:2013 was approved by CENELEC as a

European Standard with agreed common modifications.
COMMON MODIFICATIONS
2 Normative references
Replace the text of Clause 2 by:

NOTE Normative references to international publications are listed in Annex ZA (normative).

Add the text of the BIBLIOGRAPHY in Annex ZA.

10.202.2 Limitation of the touch current from the device to the dedicated HBES network

Replace the NOTE by:

NOTE When it is possible to touch the HBES network also during maintenance, the limitation of the

summation of touch current has to be considered in accordance to EN 50491-3.
26 EMC requirements
26.1 This clause is applicable with the following modifications:
th th
Replace the 6 paragraph, Note 1 and the 7 paragraph by:

For HBES switches using RF (Radio Frequency), the RF-requirements of ETSI EN 300 220-1,

ETSI EN 300 220-2 and ETSI EN 301 489-3 apply.

For immunity, the requirements of EN 60669-2-1:2004, its Amendment 1:2009 and its Amendment 12:2010

apply in addition to 26.2.
Replace the 8 paragraph and Note 2 by :

For HBES switches using PL (power line), the emission requirements of EN 50065-1 apply.

For immunity, the requirements of Part 2-1 and in addition the requirements of EN 50065-2-1 or

EN 50065-2-3, if applicable, may apply.
---------------------- Page: 5 ----------------------
SIST EN 60669-2-5:2017
EN 60669-2-5:2016
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications

The following documents, in whole or in part, are normatively referenced in this document and are

indispensable for its application. For dated references, only the edition cited applies. For undated

references, the latest edition of the referenced document (including any amendments) applies.

NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod),

the relevant EN/HD applies.

NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is

available here: www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60050 series International Electrotechnical - -
Vocabulary (IEV)

IEC 60364-4-41 (mod) - Low-voltage electrical installations - HD 60364-4-41 2007

Part 4-41: Protection for safety -
- - + corrigendum Jul. 2007
Protection against electric shock
IEC 60664-1 2007 Insulation coordination for EN 60664-1 2007
equipment within low-voltage
systems -
Part 1: Principles, requirements and
tests
IEC 60664-3 - Insulation coordination for EN 60664-3 2003
equipment within low-voltage
systems -
Part 3: Use of coating, potting or
moulding for protection against
pollution
IEC 60669-1 (mod) 1998 Switches for household and similar EN 60669-1 1999
fixed-electrical installations -
+ A1 (mod) 1999 + A1 2002
Part 1: General requirements
+ A2 (mod) 2006 + A2 2008
IEC 60669-2-1 (mod) 2002 Switches for household and similar EN 60669-2-1 2004
fixed electrical installations -
- - + corrigendum Dec. 2007
Part 2-1:
+ A1 (mod) 2008 + A1 2009
Particular requirements - Electronic
- - + A12 2010
switches
IEC 60670-1 (mod) - Boxes and enclosures for electrical EN 60670-1 2005
accessories for household and
- - + corrigendum Nov. 2007
similar fixed electrical installations -
- - Part 1: General requirements + corrigendum Mar. 2010
---------------------- Page: 6 ----------------------
SIST EN 60669-2-5:2017
EN 60669-2-5:2016
Publication Year Title EN/HD Year
IEC 60715 - Dimensions of low-voltage EN 60715 2001
switchgear and controlgear -
Standardized mounting on rails for
mechanical support of electrical
devices in switchgear and
controlgear installations
IEC 60990 - Methods of measurement of touch EN 60990 1999
current and protective conductor
current
IEC 61000-2-2 - Electromagnetic compatibility EN 61000-2-2 2002
(EMC) -
Part 2-2: Environment -
Compatibility levels for low-
frequency conducted disturbances
and signalling in public low-voltage
power supply systems
IEC 61000-3-2 - Electromagnetic compatibility EN 61000-3-2 2006
(EMC) -
Part 3-2: Limits - Limits for harmonic
current emissions (equipment input
current ≤ 16 A per phase)
IEC 61000-3-3 - Electromagnetic compatibility EN 61000-3-3 2013
(EMC) -
Part 3-3: Limits - Limitation of
voltage changes, voltage
fluctuations and flicker in public low-
voltage supply systems, for
equipment with rated current ≤ 16 A
per phase and not subject to
conditional connection
IEC 61000-4-2 - Electromagnetic compatibility EN 61000-4-2 2009
(EMC) -
Part 4-2: Testing and measurement
techniques - Electrostatic discharge
immunity test
IEC 61000-4-3 - Electromagnetic compatibility EN 61000-4-3 2006
(EMC) -
Part 4-3: Testing and measurement
techniques - Radiated, radio-
frequency, electromagnetic field
immunity test
IEC 61000-4-4 - Electromagnetic compatibility EN 61000-4-4 2012
(EMC) -
Part 4-4: Testing and measurement
techniques - Electrical fast
transient/burst immunity test
IEC 61000-4-5 - Electromagnetic compatibility EN 61000-4-5 2006
(EMC) -
Part 4-5: Testing and measurement
techniques - Surge immunity test
---------------------- Page: 7 ----------------------
SIST EN 60669-2-5:2017
EN 60669-2-5:2016
Publication Year Title EN/HD Year
IEC 61000-4-6 - Electromagnetic compatibility EN 61000-4-6 2014
(EMC) -
Part 4-6: Testing and measurement
techniques - Immunity to conducted
disturbances, induced by radio-
frequency fields
IEC 61000-4-8 - Electromagnetic compatibility EN 61000-4-8 2010
(EMC) -
Part 4-8: Testing and measurement
techniques - Power frequency
magnetic field immunity test
IEC 61000-4-11 - Electromagnetic compatibility EN 61000-4-11 2004
(EMC) -
Part 4-11: Testing and measurement
techniques - Voltage dips, short
interruptions and voltage variations
immunity tests
IEC 61000-4-20 2010 Electromagnetic compatibility EN 61000-4-20 2010
(EMC) -
Part 4-20: Testing and measurement
techniques - Emission and immunity
testing in transverse electromagnetic
(TEM) waveguides
IEC 61058-1 (mod.) 2000 Switches for appliances - EN 61058-1 2002
Part 1: General requirements
+ A1 2001 - -
+ A2 2007 + A2 2008
IEC 61140 2001 Protection against electric shock - EN 61140 2002
Common aspects for installation and
equipment
IEC 61558-2-6 - Safety of transformers, reactors, EN 61558-2-6 2009
power supply units and similar
products for supply voltages up to
1 100 V -
Part 2-6:
Particular requirements and tests for
safety isolating transformers and
power supply units incorporating
safety isolating transformers
CISPR 14 series Electromagnetic compatibility - EN 55014 series
Requirements for household
appliances, electric tools and similar
apparatus
CISPR 15 - Limits and methods of measurement EN 55015 2013
of radio disturbance characteristics
of electrical lighting and similar
equipment
CISPR 22 (mod) - Information technology equipment - EN 55022 2010
Radio disturbance characteristics -
- - + AC 2011
Limits and methods of measurement
1) EN 61058-1:2002 includes IEC 61058-1:2000/A1:2001 (not modified).
---------------------- Page: 8 ----------------------
SIST EN 60669-2-5:2017
EN 60669-2-5:2016
Annex ZB
(informative)
A-deviations

A-deviation: National deviation due to regulations, the alteration of which is for the time being outside

the competence of the CENELEC national member.

This European Standard falls under Directives 2014/30/EU, 2014/35/EU and 2014/53/EU.

NOTE (from CEN/CENELEC IR Part 2:2015, 2.16) Where standards fall under EC Directives or

Regulations, it is the view of the Commission of the European Communities (OJ No C 59, 1982-03-09) that the

effect of the decision of the Court of Justice in case 815/79 Cremonini/Vrankovich (European Court Reports 1980,

p. 3583) is that compliance with A-deviations is no longer mandatory and that the free movement of products

complying with such a standard should not be restricted within the EC except under the safeguard procedure

provided for in the relevant Directive or Regulation.

A-deviations in an EFTA-country are valid instead of the relevant provisions of the European Standard

in that country until they have been removed.
Clause Deviation
10.201 Denmark (Heavy Current Regulations, Chapter 6)
In Denmark PELV is not allowed in bath zones in residence buildings.

In Denmark protection against contacts is always required for SELV circuits in bath zones in

residence buildings. Furthermore, the maximum allowed SELV voltage is 12 V a.c. or 30 V d.c. in

these areas.
---------------------- Page: 9 ----------------------
SIST EN 60669-2-5:2017
EN 60669-2-5:2016
Annex ZZA
(informative)
Relationship between this European standard and the essential requirements
of Directive 2014/30/EU [2014 OJ L96] aimed to be covered

This European standard has been prepared under a Commission standardisation request as regards

harmonised standards in support of Directive 2014/30/EU relating to electromagnetic compatibility,

“M/xxx” / ”C(20xx) xxxx final” , to provide one voluntary means of conforming to essential

requirements of Directive 2014/30/EU of the European Parliament and of the Council of 26 February

2014 on the harmonisation of the laws of the Member States relating to electromagnetic compatibility

[2014 OJ L96].

Once this standard is cited in the Official Journal of the European Union under that Directive,

compliance with the normative clauses of this standard given in Table ZZA.1 confers, within the limits

of the scope of this standard, a presumption of conformity with the corresponding essential

requirements of that Directive, and associated EFTA regulations.
Table ZZA.1 – Correspondence between this European standard and
Annex I of Directive 2014/30/EU [2014 OJ L96]
Essential requirements of Clause(s) / sub-clause(s) Remarks / Notes
Directive 2014/30/EU of this EN
All Clause 26 —

WARNING 1: Presumption of conformity stays valid only as long as a reference to this European

standard is maintained in the list published in the Official Journal of the European Union. Users of this

standard should consult frequently the latest list published in the Official Journal of the European

Union.

WARNING 2: Other Union legislation may be applicable to the product(s) falling within the scope of

this standard.
2) Mandate not yet available.
---------------------- Page: 10 ----------------------
SIST EN 60669-2-5:2017
EN 60669-2-5:2016
Annex ZZB
(informative)
Relationship between this European standard and the safety objectives
of Directive 2014/35/EU [2014 OJ L96] aimed to be covered

This European standard has been prepared under a Commission standardisation request relating to

harmonised standards in the field of the Low Voltage Directive, M/511, to provide one voluntary means

of conforming to safety objectives of Directive 2014/35/EU of the European Parliament and of the

Council of 26 February 2014 on the harmonisation of the laws of the Member States relating to the

making available on the market of electrical equipment designed for use within certain voltage limits

[2014 OJ L96].

Once this standard is cited in the Official Journal of the European Union under that Directive,

compliance with the normative clauses of this standard given in Table ZZB.1 confers, within the limits

of the scope of this standard, a presumption of conformity with the corresponding safety objectives of

that Directive, and associated EFTA regulations.
Table ZZB.1 – Correspondence between this European standard and
Annex I of Directive 2014/35/EU [2014 OJ L96]
Safety objectives of Clause(s) / sub-clause(s) Remarks / Notes
Directive 2014/35/EU of this EN
All All except Clause 26 —

WARNING 1: Presumption of conformity stays valid only as long as a reference to this European

standard is maintained in the list published in the Official Journal of the European Union. Users of this

standard should consult frequently the latest list published in the Official Journal of the European

Union.

WARNING 2: Other Union legislation may be applicable to the product(s) falling within the scope of

this standard.
---------------------- Page: 11 ----------------------
SIST EN 60669-2-5:2017
EN 60669-2-5:2016
Annex ZZC
(informative)
Relationship between this European standard and the essential requirements
of Directive 2014/53/EU [2014 OJ L153] aimed to be covered

This European standard has been prepared under a Commission standardisation request as regards

radio equipment in support of Directive 2014/53/EU, M/536, to provide one voluntary means of

conforming to essential requirements of Directive 2014/53/EU of the European Parliament and of the

Council of 16 April 2014 on the harmonisation of the laws of the Member States relating to the making

available on the market of radio equipment and repealing Directive 1999/5/EC [2014 OJ L153].

Once this standard is cited in the Official Journal of the European Union under that Directive,

compliance with the normative clauses of this standard given in Table ZZC.1 confers, within the limits

of the scope of this standard, a presumption of conformity with the corresponding essential

requirements of that Directive, and associated EFTA regulations.
Table ZZC.1 – Correspondence between this European Standard and
Article 3 of Directive 2014/53/EU [2014 OJ L153]
Safety objectives of Clause(s) / sub-clause(s) Remarks / Notes
Directive 2014/53/EU of this EN
3.1 a) All except Clause 26 —
3.1 b) Clause 26
3.2 Clause 26
---------------------- Page: 12 ----------------------
SIST EN 60669-2-5:2017
IEC 60669-2-5
Edition 1.0 2013-10
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Switches for household and similar fixed electrical installations –
Part 2-5: Particular requirements – Switches and related accessories for use in
home and building electronic systems (HBES)
Interrupteurs pour installations électriques fixes domestiques et analogues –

Partie 2-5: Prescriptions particulières – Interrupteurs et appareils associés pour

usage dans les systèmes électroniques des foyers domestiques et bâtiments
(HBES)
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CODE PRIX X
ICS 29.120.40 ISBN 978-2-8322-1152-6

Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 13 ----------------------
SIST EN 60669-2-5:2017
– 2 – 60669-2-5 © IEC:2013
CONTENTS

FOREWORD ........................................................................................................................... 4

1 Scope ............................................................................................................................... 6

2 Normative references ....................................................................................................... 7

3 Terms and definitions ....................................................................................................... 8

4 General requirements ..................................................................................................... 10

5 General notes on tests ................................................................................................... 10

6 Rating ............................................................................................................................ 10

7 Classification .................................................................................................................. 11

8 Marking .......................................................................................................................... 12

9 Checking of dimensions .................................................................................................. 12

10 Protection against electric shock .................................................................................... 12

11 Provision for earthing ..................................................................................................... 13

12 Terminals ....................................................................................................................... 13

13 Constructional requirements ........................................................................................... 14

14 Mechanism ..................................................................................................................... 14

15 Resistance to ageing, protection provided by enclosures of switches, and

resistance to humidity ..................................................................................................... 14

16 Insulation resistance and electric strength ...................................................................... 14

17 Temperature rise ............................................................................................................ 15

18 Making and breaking capacity ........................................................................................ 15

19 Normal operation ............................................................................................................ 15

20 Mechanical strength ....................................................................................................... 16

21 Resistance to heat .......................................................................................................... 16

22 Screws, current-carrying parts and connections .............................................................. 16

23 Creepage distances, clearances and distances through sealing compound..................... 16

24 Resistance of insulating material to abnormal heat, to fire and to tracking ...................... 22

25 Resistance to rusting ...................................................................................................... 22

26 EMC requirements .......................................................................................................... 22

101 Abnormal conditions ....................................................................................................... 29

102 Components ................................................................................................................... 30

Annex A (normative) Survey of specimens needed for tests ................................................. 31

Annex B (normative) Additional requirements for switches having facilities for the

outlet and retention of flexible cables .................................................................................... 32

Annex C (informative) Examples of types of electronic switches and their functions ............. 33

Annex AA (normative) Measurement of clearances and creepage distances ........................ 34

Annex BB (informative) Test set-ups .................................................................................... 37

Bibliography .......................................................................................................................... 44

Figure 201 – Protective separation between circuits ............................................................. 19

Figure AA.1 – Narrow groove ................................................................................................ 34

Figure AA.2 – Wide groove ................................................................................................... 34

Figure AA.3 – V-shaped groove ............................................................................................ 34

---------------------- Page: 14 ----------------------
SIST EN 60669-2-5:2017
60669-2-5 © IEC:2013 – 3 –

Figure AA.4 – Rib ................................................................................................................. 35

Figure AA.5 – Uncemented joint with narrow groove ............................................................. 35

Figure AA.6 – Uncemented joint with wide groove ................................................................. 35

Figure AA.7 – Uncemented joint with narrow and wide grooves............................................. 35

Figure AA.8 – Intervening, unconnected conductive part ....................................................... 36

Figure AA.9 – Narrow recess ................................................................................................ 36

Figure AA.10 – Wide recess .................................................................................................. 36

Figure BB.1 – Test setup for AC mains connection according to IEC 61000-4-4 .................... 37

Figure BB.2 – Test setup for bus and DC mains connection according to IEC 61000-4-4 ...... 38

Figure BB.3 – Test setup for AC mains connection according to IEC 61000-4-5 .................... 39

Figure BB.4 – Test setup for bus and DC mains connection according to IEC 61000-4-5 ...... 40

Figure BB.5 – Test setup for the ESD according to IEC 61000-4-2 ........................................ 41

Figure BB.6 – Test setup for AC mains connection according to IEC 61000-4-6 .................... 42

Figure BB.7 – Test setup for bus and DC mains connection according to

IEC 61000-4-6 ...................................................................................................................... 43

Table 201 – Test loads for HBES switches for heating installations ....................................... 16

Table 202 – Relation between the rated voltage of the HBES switch, the rated

insulation voltage and the rated impulse voltage ................................................................... 17

Table 203 – Minimum clearances without verification test ..................................................... 19

Table 204 – Test voltages and corresponding altitudes ......................................................... 20

Table 205 – Minimum clearances with verification test .......................................................... 20

Table 206 – Minimum creepage distances of basic, supplementary and reinforced

insulation without verification test ......................................................................................... 21

Table 207 – Minimum creepage distances of basic, supplementary and reinforced

insulation with verification test .............................................................................................. 21

Table 208 – Immunity tests (overview) .....................
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.