Refuse collection vehicles and their associated lifting devices - General requirements and safety requirements - Part 4: Noise test code for refuse collection vehicles

This European Standard defines the measurement of noise emitted by refuse collection vehicles (RCVs). Its goal is to obtain the sound pressure level at the operator's position and the sound power level of RCVs.
The test results obtained in accordance with this standard are also applicable to the evaluation of the hazards generated by noise from RCVs.
This standard deals with the noise measurement conditions for the types of refuse collection vehicles defined and described in the standards of the series EN 1501.
This standard addresses the uncertainties due to measurement procedures.
This standard does not address the discharge operation as this operation is short in time (1 % of the working period) with a sound pressure level equivalent to the sound pressure level of the main operation.
In view of the wide variety of RCVs, it could be appropriate to refer to individual RCVs as falling into classes or groups (model of equipment within a given type of equipment) having in common specific features regarding noise measurements and characteristics. A possible classification is proposed in an informative annex, enabling both producers and users to address a limited number of well defined classes/groups suitable for determination of noise emission values.

Abfallsammelfahrzeuge und die dazugehörigen Schüttungen - Allgemeine Anforderungen und Sicherheitsanforderungen - Teil 4: Geräuschprüfverfahren für Abfallsammelfahrzeuge

Diese Europäische Norm legt die Messung von Lärm, der durch Abfallsammelfahrzeuge (ASF) entsteht, fest.
Der Zweck ist die Bestimmung des Schalldruckpegels am Arbeitsplatz des Bedienpersonals und des Schallleistungspegels von ASF beim Sammeln des Abfalls. Sie  legt  ein genormtes Verfahren zum Messen und zum späteren Vergleich von ASF-Lärmemissionen fest und beschreibt die Messung bei vier Betriebsbedingungen: Betrieb des Fahrgestells, des Verdichtungssystems, Heben und Herabfallen des Abfalls in das ASF.
Zusammen mit den Angaben zu anderen Parametern gelten die in Übereinstimmung mit dieser Norm erzielten Prüfergebnisse ebenfalls für die Bewertung der Gefährdungen durch von ASF erzeugten Lärm.
Diese Norm behandelt die Messunsicherheiten der Messverfahren.
Diese Norm behandelt die Lärmmessbedingungen für die Typen von Abfallsammelfahrzeugen, die in der Normenreihe EN 1501 beschrieben sind.

Bennes de collecte des déchets et leurs lève-conteneurs associés - Exigences générales et exigences de sécurité - Partie 4 - Code d'essai acoustique des bennes de collecte des déchets

La présente Norme européenne définit le mesurage du bruit émis par les bennes de collecte des déchets.
Elle a pour objectif, d’une part, de déterminer le niveau de pression acoustique aux postes opérateur et,
d’autre part, le niveau de puissance acoustique des bennes de collecte des déchets pendant le collecte des
déchets. Elle prescrit un mode opératoire normalisé pour le mesurage et la comparaison ultérieure des
émissions sonores des bennes de collecte des déchets comprenant quatre conditions d’exploitation : le
fonctionnement du châssis-cabine, le fonctionnement du systeme de compaction, le fonctionnement du
systeme de levage et le vidage de déchets conventionnels dans la benne de collecte des déchets.
Avec les informations relatives a d’autres parametres, les résultats des essais obtenus conformément a la
présente norme s’appliquent également a l’évaluation des phénomenes dangereux résultant du bruit émis par
les bennes de collecte des déchets.
La présente norme traite des incertitudes inhérentes aux modes opératoires de mesurage.
La présente norme traite des conditions de mesurage du bruit des types de bennes de collecte des déchets
définis et décrits dans les normes de la série EN 1501.

Vozila za zbiranje odpadkov in pripadajoči iztresalniki - Splošne in varnostne zahteve - 4. del: Navodilo za merjenje hrupa vozil za zbiranje odpadkov

General Information

Status
Withdrawn
Publication Date
08-Jan-2008
Withdrawal Date
21-May-2023
Technical Committee
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
18-May-2023
Due Date
10-Jun-2023
Completion Date
22-May-2023

Relations

Buy Standard

Standard
EN 1501-4:2008
English language
19 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
prEN 1501-4:2006
English language
18 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
prEN 1501-4:2004
English language
16 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.SDGNRYAbfallsammelfahrzeuge und die dazugehörigen Schüttungen - Allgemeine Anforderungen und Sicherheitsanforderungen - Teil 4: Geräuschprüfverfahren für AbfallsammelfahrzeugeBennes de collecte des déchets et leurs lève-conteneurs associés - Exigences générales et exigences de sécurité - Partie 4 - Code d'essai acoustique des bennes de collecte des déchetsRefuse collection vehicles and their associated lifting devices - General requirements and safety requirements - Part 4: Noise test code for refuse collection vehicles43.160Vozila za posebne nameneSpecial purpose vehicles17.140.30Emisija hrupa transportnih sredstevNoise emitted by means of transport13.030.40Naprave in oprema za odstranjevanje in obdelavo odpadkovInstallations and equipment for waste disposal and treatmentICS:Ta slovenski standard je istoveten z:EN 1501-4:2007SIST EN 1501-4:2008en,fr,de01-februar-2008SIST EN 1501-4:2008SLOVENSKI
STANDARD



SIST EN 1501-4:2008



EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 1501-4October 2007ICS 17.140.30; 43.160 English VersionRefuse collection vehicles and their associated lifting devices -General requirements and safety requirements - Part 4: Noisetest code for refuse collection vehiclesBennes de collecte des déchets et leurs lève-conteneursassociés - Exigences générales et exigences de sécurité -Partie 4 - Code d'essai acoustique des bennes de collectedes déchetsAbfallsammelfahrzeuge und die dazugehörigenSchüttungen - Allgemeine Anforderungen undSicherheitsanforderungen - Teil 4: Geräuschprüfverfahrenfür AbfallsammelfahrzeugeThis European Standard was approved by CEN on 8 September 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2007 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 1501-4:2007: ESIST EN 1501-4:2008



EN 1501-4:2007 (E) 2 Contents Page Foreword.3 Introduction.4 1 Scope.5 2 Normative references.5 3 Terms and definitions.6 4 Preparation of the RCV for measurements.6 4.1 Test environment.6 4.2 Choice of the RCV.6 4.3 Position of the RCV during measurement.6 5 Operating conditions (before and) during measurement.6 5.1 RCV conditions.6 5.2 Presetting the engine speed.6 5.3 Fan speed.7 5.4 Selection of operations.7 5.5 Chassis operation.8 5.6 Compaction system operation.8 5.7 Lifting, tilting and lowering of a container operation.8 5.8 Dumping of specified waste into the hopper.8 6 Noise measurement.9 6.1 General.9 6.2 Microphone positions.9 6.3 Measurement durations.9 6.4 Measurements.10 7 Determination of the averaged sound power level for a combination of operating conditions.11 8 Uncertainties.12 8.1 Measurement uncertainties.12 8.2 Production uncertainties.12 9 Information to be reported.12 10 Declaration, labelling and information for use.13 Annex A (normative)
Information to be reported.14 Annex B (normative)
Microphone positions.15 Annex C (informative)
Proposed classification of RCVs for noise measurement purposes (Valid for rear/side/front loaded).17 Annex ZA (informative)
Relationship between this European Standard and the Essential Requirements of EU Directive 98/37/EC, amended by 98/79/EC.18 Annex ZB (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC.19
SIST EN 1501-4:2008



EN 1501-4:2007 (E) 3 Foreword This document (EN 1501-4:2007) has been prepared by Technical Committee CEN/TC 183 “Waste management”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2008, and conflicting national standards shall be withdrawn at the latest by April 2008. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annexes ZA and ZB, which are an integral part of this document. This European Standard is the fourth part of the series of co-ordinated standards of EN 1501 about “Refuse collection vehicles and their associated lifting devices - General requirements and safety requirements -” comprising the other following parts:  Part 1: Rear-end loaded refuse collection vehicles  Part 2: Side loaded refuse collection vehicles  Part 3: Front loaded refuse collection vehicles (under preparation)  Part 5: Lifting devices for refuse collection vehicles (under preparation). It augments the above mentioned type C standards. Its purpose is to provide a means for the determination and declaration of noise emission by RCVs falling within the scope of the standards of the EN 1501 series. The determination of noise emission values is a prerequisite for a manufacturer to assess the noise reduction obtained at the design stage. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. SIST EN 1501-4:2008



EN 1501-4:2007 (E) 4 Introduction
EU Directive 2000/14/EC “Noise Emission in the Environment by Equipment for Use Outdoor” requires manufacturers within the EU and importers from outside the EU to mark and certify RCVs with a guaranteed sound power level. This European Standard provides a procedure for the measurement and calculation of sound power emitted by RCVs thus enabling manufacturers and importers to mark and certify all three types of RCV in compliance with the above mentioned EU Directive. This standard also covers the noise information requirements of EU Directive 98/37/EC relating to Machinery for the measurement of the sound pressure levels at the operator’s positions. The machinery concerned and the extent to which hazards, hazardous situations and events are covered are indicated in the scope of this document. This document is a type C standard as stated in EN ISO 12100. When provisions of this type C standard are different from those which are stated in type A or B standards, the provisions of this type C standard take precedence over the provisions of the other standards, for machines that have been designed and built according to the provisions of this type C Standard. SIST EN 1501-4:2008



EN 1501-4:2007 (E) 5 1 Scope This European Standard specifies the method for measuring the noise emission, which is a significant hazard of refuse collection vehicles (RCVs). Its goal is to obtain, on one hand, the emission sound pressure level at the operator’s position(s) and, on the other hand, the sound power level of the RCV during waste collection. It specifies a standardized procedure for measurement and later comparison of RCVs noise emission, consisting of four operating conditions: chassis operation, compaction operation, lifting, tilting and lowering operation of a container and dumping of specified waste into the RCV. Together with information concerning other parameters, the test results obtained in accordance with this standard are also applicable to the evaluation of the hazards generated by noise from RCVs. This standard addresses the uncertainties due to measurement procedures. This standard deals with the noise measurement conditions for the types of RCVs defined and described in the standards of the EN 1501 series. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 840-1, Mobile waste containers — Part 1: Containers with 2 wheels with a capacity up to 400 l for comb lifting devices, dimensions and design EN 1452-2, Plastics piping systems for water supply — Unplasticized poly (vinyl chloride) (PVC-U) — Part 2: Pipes EN 1501-1, Refuse collection vehicles and their associated lifting devices - General requirements and safety requirements - Part 1: Rear-end loaded refuse collection vehicles EN 1501-2, Refuse collection vehicles and their associated lifting devices — General requirements and safety requirements — Part 2: Side loaded refuse collection vehicles prEN 1501-3, Refuse collection vehicles and their associated lifting devices — General requirements and safety requirements — Part 3: Front loaded refuse collection vehicles EN ISO 3744:1995, Acoustics - Determination of sound power levels of noise sources using sound pressure - Engineering method in an essentially free field over a reflecting plane (ISO 3744:1994) EN ISO 4871:1996, Acoustics - Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996) EN ISO 11201:1995, Acoustics - Noise emitted by machinery and equipment - Measurement of emission sound pressure levels at a work station and at other specified positions - Engineering method in an essentially free field over a reflecting plane (ISO 11201:1995) EN ISO 12100-1:2003, Safety of machinery - Basic concepts, general principles for design - Part 1: Basic terminology, methodology (ISO 12100-1:2003) EN ISO 12100-2:2003, Safety of machinery - Basic concepts, general principles for design - Part 2: Technical principles (ISO 12100-2:2003) SIST EN 1501-4:2008



EN 1501-4:2007 (E) 6 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN ISO 3744:1995, EN ISO 4871:1996, EN ISO 12100-1:2003, EN ISO 12100-2:2003, EN ISO 11201:1995 and in the series of standards EN 1501 apply, together with the following. 3.1 shaking mode part of the lifting cycle where the waste container, in its tilted position, is moved back and forth and/or hits a mechanical stop device, either by a specific command or automatically, in order to get all the waste out of it 4 Preparation of the RCV for measurements 4.1 Test environment For the test site, test environment and measurement conditions, the requirements of EN ISO 11201:1995 and EN ISO 3744:1995 shall be fulfilled. 4.2 Choice of the RCV Measurements shall be carried out on a sample RCV that has the noise emission characteristics of a series of produced RCVs or of a specific RCV class or group (see the note in Clause 9 and Annex C). 4.3 Position of the RCV during measurement
The RCV shall be tested in a stationary position. The RCV shall be positioned with its longitudinal axis along the x-axis of the co-ordinate system used to fix the microphone positions and with its mid-length over the origin (see Figure B.2). 5 Operating conditions (before and) during measurement 5.1 RCV conditions The engine and hydraulic system shall be warmed up in accordance with the instructions and safety requirements. The information specified in the information for use manual shall also be observed. No signalling device such as warning horn or reverse auditory signal (buzzer) shall be operated during the test. If the RCV is fitted with several engines, they shall work simultaneously during the tests. If this is not possible, each possible combination of engines shall be tested. For measurements inside the cab, the doors and windows shall be closed and any noisy in-cab equipment (fan, radio, air conditioner, etc) off. 5.2 Presetting the engine speed For all four noise measurement operations of chassis, compaction, lifting, tilting and lowering of an empty waste container and dumping of waste into the hopper, the engine speed shall be that provided by the automatic engine accelerator which has been preset by the RCV manufacturer. The engine speed shall be measured for each of the four operations. SIST EN 1501-4:2008



EN 1501-4:2007 (E) 7 If the measured engine speed is lower than the preset speed provided by the RCV manufacturer by more than 5 %, the engine speed shall be increased by the cab accelerator to the intended preset speed. If the engine speed for any of the four operations is not provided by the RCV manufacturer or if the vehicle is not provided with an automatic accelerator, the engine speed shall be set up at 1 200 rpm by the cab accelerator. 5.3 Fan speed 5.3.1 General If the engine of the RCV and/or its hydraulic system are (is) fitted with one or more fan(s), they (it) shall operate during the test. The fan speed to be used shall be in accordance with one of the following conditions (5.3.2 to 5.3.4), depending on the conditions set by the manufacturer of the equipment, and shall appear in the test report, this speed being used in further measurements. 5.3.2 Fan drive directly connected to the engine If the fan drive is directly connected to the engine and/or hydraulic equipment (e.g. by belt drive) it shall operate during the test.
...

SLOVENSKI oSIST prEN 1501-4:2006

PREDSTANDARD
julij 2006
Vozila za zbiranje odpadkov in pripadajoči iztresalniki – Splošne in varnostne
zahteve – 4. del: Navodilo za merjenje hrupa vozil za zbiranje odpadkov
Refuse collection vehicles and their associated lifting devices - General
requirements and safety requirements - Part 4: Noise test code for refuse collection
vehicles
ICS 17.140.30; 43.160 Referenčna številka
oSIST prEN 1501-4:2006(en)
©  Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno

---------------------- Page: 1 ----------------------
EUROPEAN STANDARD
DRAFT
prEN 1501-4
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2006
ICS

English Version
Refuse collection vehicles and their associated lifting devices -
Part 4: Noise test code for refuse collection vehicles
Bennes de collecte des déchets et leurs lève-conteneurs Abfallsammelfahrzeuge und die dazugehörigen
associés - Partie 4 : Code d'essai de mesurage du bruit Schüttungen - Teil 4: Geräuschprüfverfahren für
des bennes de collecte des déchets Abfallsammelfahrzeuge
This draft European Standard is submitted to CEN members for second enquiry. It has been drawn up by the Technical Committee
CEN/TC 183.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2006 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 1501-4:2006: E
worldwide for CEN national Members.

---------------------- Page: 2 ----------------------
prEN 1501-4:2006 (E)
Contents Page
Foreword.3
Introduction .4
1 Scope .5
2 Normative references .5
3 Terms and definitions .6
4 Preparation of the RCV for measurements .6
4.1 Test environment.6
4.2 Choice of the RCV.6
4.3 Position of the RCV during measurement .6
5 Operating conditions (before and) during measurement.6
5.1 RCV conditions .6
5.2 Fan speed .7
5.3 Selection of operations .7
5.4 Chassis operation.7
5.5 Compaction system operation .8
5.6 Lifting of empty waste container(s) .8
5.7 Waste falling into the RCV .8
6 Noise measurement.9
6.1 General.9
6.2 Microphone positions .9
6.3 Measurement durations .9
6.4 Measurements.10
7 Determination of the sound power level for a combination of operating conditions.11
8 Measurement uncertainties .12
9 Test report and information to be reported .12
10 Declaration, information for use .13
Annex A (normative) Information to be reported.14
Annex B (normative) .15
Annex C (informative) Proposed classification of RCVs for noise measurement purposes (Valid
for rear/side/front loaded RCVs) .17
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 98/37/EC, amended by 98/79/EC.18

2

---------------------- Page: 3 ----------------------
prEN 1501-4:2006 (E)
Foreword
This document (prEN 1501-4:2006) has been prepared by Technical Committee CEN/TC 183 “Waste
management”, the secretariat of which is held by DIN.
This document is currently submitted to the second CEN Enquiry.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document.
This European Standard is one part of the series of co-ordinated standards of EN 1501 about “Refuse
collection vehicles and their associated lifting devices” comprising the other following parts:
 Part 1: Rear loaded refuse collection vehicles, as amended by A1: Footboards (under revision)
 Part 2: Side loaded refuse collection vehicles
 Part 3: Front loaded refuse collection vehicles (under preparation)
 Part 5: Lifting devices for refuse collection vehicles (under preparation)
 Part 6: Electromagnetic compatibility of refuse collection vehicles (under preparation).
It augments the “C”-type safety standards prepared by CEN/TC183.
Its purpose is to provide a means of determination, declaration and verification of noise emission for the
equipment within the scope of this standard. The determination of noise emission values is a prerequisite for a
manufacturer to assess the noise reduction obtained at the design stage.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive 98/37/EC.
For relationship with EU Directive(s), see informative Annex ZA,, which is an integral part of this document.
The Annexes A and B are normative. The Annexes C and ZA are informative.
3

---------------------- Page: 4 ----------------------
prEN 1501-4:2006 (E)
Introduction
This European Standard deals with the measurement of noise emitted by refuse collection vehicles (RCVs) in
view of the declaration and marking of the sound power level to fulfil the requirements of
EU Directive 2000/14/EC on the approximation of the laws of the Member states relating to the noise emission
in the environment by equipment for use outdoors. It also covers the noise information requirements of
EU Directive 98/37/EC on the approximation of the laws of the Member states relating to machinery.
The machinery concerned and the extent to which hazards, hazardous situations and events are covered are
indicated in the scope of this document.
This document is a type C standard as stated in EN 1070.
4

---------------------- Page: 5 ----------------------
prEN 1501-4:2006 (E)
1 Scope
This European Standard defines the measurement of noise emitted by refuse collection vehicles (RCVs).
Its goal is to obtain, on one hand, the sound pressure level at the operative’s position(s) and, on the other
hand, the sound power level of the RCV during waste collection. It specifies a standardized procedure for
measurement and later comparison of RCVs noise emission, consisting of four operating conditions: chassis
operation, compaction operation, lifting operation and specified waste falling into the RCV.
Together with information concerning other parameters, the test results obtained in accordance with this
standard are also applicable to the evaluation of the hazards generated by noise from RCVs.
This standard addresses the uncertainties due to measurement procedures.
This standard deals with the noise measurement conditions for the types of RCVs defined and described in
the standards of the series EN 1501.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
EN ISO 12100-2:2004, Safety of machinery — Basic concepts, general principles for design —
Part 2: Technical principles
EN 840-1:2004, Mobile waste containers — Part 1: Containers with 2 wheels with a capacity up to 400 l for
comb lifting devices — Dimensions and design
EN 1070:1998, Safety of machinery - Terminology
EN 1452-2:1999, Plastics piping systems for water supply — Unplasticized poly (vinyl chloride) (PVC-U) —
Part 2: Pipes
EN 1501-1:1998, Refuse collection vehicles and their associated lifting devices — General requirements and
safety requirements — Part 1: Rear loaded refuse collection vehicles
EN 1501-2:2005, Refuse collection vehicles and their associated lifting devices — General requirements and
safety requirements — Part 2: Side loaded refuse collection vehicles
prEN 1501-3, Refuse collection vehicles and their associated lifting devices — General requirements and
safety requirements — Part 3: Front loaded refuse collection vehicles (under preparation)
EN ISO 3744:1995, Acoustics — Determination of sound power levels of noise sources using sound
pressure — Engineering method in an essentially free field over a reflecting plane
EN ISO 4871:1997, Acoustics — Declaration and verification of noise emission values of machinery and
equipment
EN ISO 11201:1995, Acoustics — Noise emitted by machinery and equipment — Measurement of emission
sound pressure levels at a work station and at other specific positions — Engineering method in an essentially
free field over a reflecting plane
5

---------------------- Page: 6 ----------------------
prEN 1501-4:2006 (E)
3 Terms and definitions
For the purposes of this European Standard, the terms and definitions given in EN ISO 3744:1995,
EN ISO 4871:1995, EN ISO 11201:1995 and in the series of standards EN 1501 apply, together with the
following:
3.1
collection mode
RCV with all the functions of the bodywork operating or ready to operate
NOTE This mode excludes the travel movement
3.2
shaking mode
part of the lifting cycle where the waste container, in its tilted position, is moved back and forth and/or hits a
mechanical stop device, either by a specific command or automatically, in order to get all the waste out of it
4 Preparation of the RCV for measurements
4.1 Test environment
For the test site, test environment and measurement conditions, the requirements of EN ISO 11201:1995 and
EN ISO 3744:1995 shall be fulfilled.
4.2 Choice of the RCV
Measurements shall be carried out on a sample RCV that has the noise emission characteristics of a series of
produced RCVs or of a specific RCV class or group (see note in sub-clause 9 and Annex C).
4.3 Position of the RCV during measurement
The RCV shall be tested in a stationary position.
The RCV shall be positioned with its longitudinal axis along the x-axis of the co-ordinate system used to fix the
microphone positions and with its mid-length L/2 over the origin “O” (see Figure B.1).
5 Operating conditions (before and) during measurement
5.1 RCV conditions
The engine and hydraulic system shall be warmed up in accordance. The instructions and safety requirements,
as specified in the information for use manual, shall be observed
No signalling device such as warning horn or reverse auditory signal (buzzer) shall be operated during the test.
If the RCV is fitted with several engines, they shall work simultaneously during the tests. If this is not possible,
each possible combination of engines shall be tested.
For measurements inside the cab, the doors and windows shall be closed and any noisy in-cab equipment
(fan, radio, air conditioner, etc) off.
6

---------------------- Page: 7 ----------------------
prEN 1501-4:2006 (E)
5.2 Fan speed
If the engine of the RCV or its hydraulic system is fitted with one (a) fan(s), it (they) must operate during the
test. The fan speed to be used shall be in accordance with one of the following conditions, depending on the
conditions set by the manufacturer of the equipment, and must appear in the test report, this speed being
used in further measurements.
a) Fan drive directly connected to the engine:
If the fan drive is directly connected to the engine and/or hydraulic equipment (e.g. by belt drive) it must
operate during the test.
b) Fan drive with several distinct speeds:
If the fan can work at several distinct speeds, the test shall be carried out
 either at its maximum speed,
 or in a first test with the fan set at zero speed and in a second test with the fan set at maximum
speed.
c) Fan drive with continuous variable speed:
If the fan can work at continuous variable speed, the test shall be carried out either according to 5.1b) or with
the fan speed set by the manufacturer at no less than 70 % of the maximum speed.
Note: If the fan speed is automatically regulated by the engine temperature and if preliminary
noise measurement investigations have shown that the influence of the fan speed measured at
microphone positions is less than 1 dB (A), then only one fan speed condition can be used.
5.3 Selection of operations
The noise emission of the RCV is determined considering four operating conditions:
 chassis operation (in the collection mode),
 compaction operation,
 lifting, tilting and lowering operation of an empty waste container,
 specified waste falling into the RCV.
...

SLOVENSKI OSIST prEN 1501-4:2004

PREDSTANDARD
maj 2004
Refuse collection vehicles and their associated lifting devices - General
requirements and safety requirements - Part 4: Noise measurement protocol for
refuse collection vehicles
ICS 43.160 Referenčna številka
OSIST prEN 1501-4:2004(en)
©  Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno

---------------------- Page: 1 ----------------------
EUROPEAN STANDARD
DRAFT
prEN 1501-4
NORME EUROPÉENNE
EUROPÄISCHE NORM
February 2004
ICS
English version
Refuse collection vehicles and their associated lifting devices -
General requirements and safety requirements - Part 4: Noise
measurement protocol for refuse collection vehicles
Bennes à ordures ménagères et leurs lève-conteneurs
associés - Exigences générales et exigences de sécurité -
Partie 4 : Protocole de mesurage du bruit des bennes
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 183.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2004 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 1501-4:2004: E
worldwide for CEN national Members.

---------------------- Page: 2 ----------------------
prEN 1501-4:2004 (E)
Contents Page
Foreword. 3
Introduction . 3
1 Scope . 3
2 Normative references . 4
3 Terms and definitions. 4
4 Installation and equipment . 5
5 Operating conditions during measurement . 5
6 Noise measurement. 8
7 Emission sound pressure levels and sound power levels for a series of operating
conditions. 10
8 Measurement uncertainties . 11
9 Declaration. 11
Annex A (normative) Information to be reported. 12
Annex B (normative) Microphone positions. 13
Annex C (informative) Proposed classification of RCVs for noise measurement purposes (Valid
for rear/side/front loaded RCVs). 15
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 98/37/EC, amended by 98/79/EC. 16
2

---------------------- Page: 3 ----------------------
prEN 1501-4:2004 (E)
Foreword
This document (prEN 1501-4:2004) has been prepared by Technical Committee CEN/TC 183 “Waste
management”, the secretariat of which is held by DIN.
This document is currently submitted to the CEN Enquiry.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, B, C or D, which is an integral part of this
document.
The annexes A and B are normative, the annexes C and ZA are informative.
Introduction
This European Standard deals with the measurement of noise emitted by refuse collection vehicles (RCVs) in
view of the declaration and marking of the noise emission level to fulfill the requirements of EU Directive
2000/14 on the approximation of the laws of the Member states relating to the noise emission in the
environment by equipment for use outdoors. It also covers the noise information requirements of EU Directive
98/37 on the approximation of the laws of the Member states relating to machinery.
1 Scope
This European Standard defines the measurement of noise emitted by refuse collection vehicles (RCVs). Its
goal is to obtain the sound pressure level at the operator’s position and the sound power level of RCVs.
The test results obtained in accordance with this standard are also applicable to the evaluation of the hazards
generated by noise from RCVs.
This standard deals with the noise measurement conditions for the types of refuse collection vehicles defined
and described in the standards of the series EN 1501.
This standard addresses the uncertainties due to measurement procedures.
This standard does not address the discharge operation as this operation is short in time (1 % of the working
period) with a sound pressure level equivalent to the sound pressure level of the main operation.
In view of the wide variety of RCVs, it could be appropriate to refer to individual RCVs as falling into classes or
groups (model of equipment within a given type of equipment) having in common specific features regarding
noise measurements and characteristics. A possible classification is proposed in an informative annex,
enabling both producers and users to address a limited number of well defined classes/groups suitable for
determination of noise emission values.
3

---------------------- Page: 4 ----------------------
prEN 1501-4:2004 (E)
2 Normative references
This European Standard incorporates by dated or undated reference, provisions from other publications.
These normative references are cited at the appropriate places in the text and the publications are listed
hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to
this European Standard only when incorporated in it by amendment or revision. For undated references the
latest edition of the publication referred to applies (including amendments).
EN 292-2:1996, Safety of machinery — Basics concepts, general principles for design — Part 2: Technical
principles and specifications.
prEN 840-1:2001, Mobile waste containers — Part 1: Containers with 2 wheels with a capacity up to 400 l for
comb lifting devices — Dimensions and design.
EN 1452-2:1999, Plastics piping systems for water supply — Unplasticized poly (vinyl chloride) (PVC-U) —
Part 2: Pipes.
EN 1501-1:1998, Refuse collection vehicles and their associated lifting devices — General requirements and
safety requirements — Part 1: Rear-end loaded refuse collection vehicles.
prEN 1501-2:2000, Refuse collection vehicles and their associated lifting devices — General requirements
and safety requirements — Part 2: Side loaded refuse collection vehicles.
1)
prEN 1501-3: , Refuse collection vehicles and their associated lifting devices — General requirements —
Part 3: Front-end loaded refuse collection vehicles
EN ISO 3744:1995, Acoustics — Determination of sound power levels of noise sources using sound
pressure — Engineering method in an essentially free-field over a reflecting plane.
EN ISO 4871:1997, Acoustics — Declaration and verification of noise emission values of machinery and
equipment.
EN ISO 11201:1995, Acoustics — Noise emitted by machinery and equipment — Measurement of emission
sound pressure levels at a work station and at other specific positions — Engineering method in an essentially
free field over a reflecting plane.
3 Terms and definitions
For the purposes of this European Standard the terms and definitions given in EN ISO 3744:1995,
EN ISO 4871:1995, EN ISO 11201:1995 and in the series standards of EN 1501 apply, together with the
following:
3.1
A-weighted emission sound pressure level at the operator’s position for a series of operating
conditions, L
pAZ
the average sound pressure level at the operator’s position from different operating conditions, determined in
accordance with the equation
0,1 L 0,1 L 0,1 L 0,1 L
L = 10 lg {[1/(a+b+c+d)] x [(a x 10 + b x 10 +c x 10 + d x 10 )]} dB
pAZ
pAa pAb pAc pAd
where
p
a is the proportion factor – chassis operation (5.3);

1) Under elaboration
4

---------------------- Page: 5 ----------------------
prEN 1501-4:2004 (E)
bp is the proportion factor – compaction operation (5.4);
cp is the proportion factor – lifting operation (5.5);
dp is the proportion factor – waste falling operation (5.6);
L is the A-weighted emission sound pressure level at the operator’s position during chassis
pAa
operation;
L is the A-weighted emission sound pressure level at the operator’s position during compaction;
pAb
L is the A-weighted emission sound pressure level at the operator’s position during lifting;
pAc
L is the A-weighted emission sound pressure level at the operator’s position with waste falling.
pAd
3.2
A-weighted sound power level for a series of operating conditions, L
WAZ
the average sound power level from different operating conditions, determined in accordance with the
equation
0,1 L 0,1 L
L = 10 lg {[1/(b+c)] x [(b x 10 +c x 10 )]} dB
WAZ WAb WAc
where
bw is the proportion factor – compaction operation (5.4);
cw is the proportion factor – lifting operation (5.5);
L is the A-weighted sound power level during compaction;
WAb
L is the A-weighted sound power level during lifting.
Wac
4 Installation and equipment
4.1 Test environment
For the test site, test environment and measurement conditions, the requirements of EN ISO 11201:1995 and
EN ISO 3744:1995 shall be fulfilled.
4.2 Equipment and condition of the RCV
Measurements shall be made on a sample RCV that has the noise emission characteristics of series
production RCVs or of a specific RCV class or group.
4.3 Position of the RCV during measurement
The RCV shall be positioned with its longitudinal axis along the x-axis of the co-ordinate system used to fix the
microphone positions and with its mid-length L/2 over the origin “O” (see Figure B.1).
5 Operating conditions during measurement
5.1 Fan speed
If the engine of the equipment or its hydraulic system is fitted with one or more fans, it (they) shall operate
during the test. The fan speed to be used shall be in accordance with one of the following conditions,
depending on the conditions set by the manufacturer of the equipment, and shall appear in the test report, this
speed being used in further measurements.
5

---------------------- Page: 6 ----------------------
prEN 1501-4:2004 (E)
a) Fan drive directly connected to the engine:
if the fan drive is directly connected to the engine and/or hydraulic equipment (e.g. by belt drive) it shall
operate during the test.
b) Fan drive with several distinct speeds:
if the fan can work at several distinct speeds the test shall be carried out either
 at its maximum speed (related to the speed of the engine), or
 in a first test with the fan set at zero speed and in a second test with the fan set at maximum speed
(related to the speed of the engine).
c) Fan drive with continuously variable speed:
if the fan can work at continuously variable speeds, the test shall be carried out either according to 5.1b)
or with the fan speed set by the manufacturer at no less than 70 % of the maximum speed (related to the
speed of the engine).
5.2 Engine
For these measurements the RCV shall be tested in a stationary position, the engine (driving device) and
hydraulic system of the equipment shall be warmed up in accordance with the instructions, and safety
requirements shall be observed. No signalling device such as a warning horn or reversing alarm shall be
operated during the test.
The speed of the engine during the test shall be recorded and appear in the test report.
If the RCV is fitted with several engines and/or aggregates they shall work simultaneously during the tests.
If this is not possible, each possible combination of engine(s) and/or aggregates shall be tested.
For each type of RCV that is to be tested under load, specific operating conditions shall be laid down which
shall, in principle, produce effects and stresses similar to those encountered under actual working conditions.
5.3 Chassis operation
Before making noise measurements, the engine and hydraulic system of the equipment shall be warmed up in
accordance with the instructions, and safety requirements shall be observed.
The noise measurements shall be carried out with the RCV in a stationary position without operating the
compaction and lifting mechanisms. For the purpose of the test, the engine shall be warmed up and set up at
the maximum speed provided by the engine manufacturer.
The speed of the engine during the test shall be recorded and shall appear in the test report.
If the RCV is fitted several engines, they shall work simultaneously during the tests. If this is not possible,
each possible combination of engine(s) shall be tested.
This test is not carried out for RCVs with electrical supply only.
5.4 Compaction system operation
For noise measurements with the compaction system operating, the body of the RCV and the hopper
receiving the waste shall be empty.
6

---------------------- Page: 7 ----------------------
prEN 1501-4:2004 (E)
If the engine is set up to the maximum working speed of the chassis when the compaction sys
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.