SIST ISO 4379:2020
(Main)Plain bearings - Copper alloy bushes
Plain bearings - Copper alloy bushes
This document specifies dimensions and tolerances for cylindrical and flanged bushes with internal diameter, d1, in the range 6 mm to 200 mm.
It applies to solid mono‑metal copper alloy bushes to be used as plain bearings with and without oil holes and oil grooves.
Paliers lisses - Bagues en alliages de cuivre
Drsni ležaji - Ležajne blazinice iz bakrovih zlitin
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST ISO 4379:2020
01-september-2020
Drsni ležaji - Ležajne blazinice iz bakrovih zlitin
Plain bearings - Copper alloy bushes
Paliers lisses - Bagues en alliages de cuivre
Ta slovenski standard je istoveten z: ISO 4379:2018
ICS:
21.100.10 Drsni ležaji Plain bearings
77.150.30 Bakreni izdelki Copper products
SIST ISO 4379:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST ISO 4379:2020
---------------------- Page: 2 ----------------------
SIST ISO 4379:2020
INTERNATIONAL ISO
STANDARD 4379
Third edition
2018-10
Plain bearings — Copper alloy bushes
Paliers lisses — Bagues en alliages de cuivre
Reference number
ISO 4379:2018(E)
©
ISO 2018
---------------------- Page: 3 ----------------------
SIST ISO 4379:2020
ISO 4379:2018(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved
---------------------- Page: 4 ----------------------
SIST ISO 4379:2020
ISO 4379:2018(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Dimensions and tolerances . 1
5 Material . 5
6 Surface finish . 5
7 Construction . 6
8 Quality assurance . 6
9 Designation . 6
Bibliography . 7
© ISO 2018 – All rights reserved iii
---------------------- Page: 5 ----------------------
SIST ISO 4379:2020
ISO 4379:2018(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: www .iso .org/iso/foreword .html.
This document was prepared by Technical Committee ISO/TC 123, Plain bearings, Subcommittee SC 3,
Dimensions, tolerances and construction details.
This third edition cancels and replaces the second edition (ISO 4379:1993), of which it constitutes a
minor revision. The changes compared to the previous edition are as follows:
— In Clause 2, all dated references have been changed to undated ones.
— A new Clause 3 Terms and definitions has been added.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/members .html.
iv © ISO 2018 – All rights reserved
---------------------- Page: 6 ----------------------
SIST ISO 4379:2020
INTERNATIONAL STANDARD ISO 4379:2018(E)
Plain bearings — Copper alloy bushes
1 Scope
This document specifies dimensions and tolerances for cylindrical and flanged bushes with internal
diameter, d , in the range 6 mm to 200 mm.
1
It applies to solid mono-metal copper alloy bushes to be used as plain bearings with and without oil
holes and oil grooves.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 1302, Geometrical Product Specifications (GPS) — Indication of surface texture in technical product
documentation
ISO 2768-1, General tolerances — Part 1: Tolerances for linear and angular dimensions without individual
tolerance indications
ISO 4382-1, Plain bearings — Copper alloys — Part 1: Cast copper alloys for solid and multilayer thick-
walled plain bearings
ISO 4382-2, Plain bearings — Copper alloys — Part 2: Wrought copper alloys for solid plain bearings
3 Terms and definitions
No terms and definitions are listed in this document.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online bro
...
INTERNATIONAL ISO
STANDARD 4379
Third edition
2018-10
Plain bearings — Copper alloy bushes
Paliers lisses — Bagues en alliages de cuivre
Reference number
ISO 4379:2018(E)
©
ISO 2018
---------------------- Page: 1 ----------------------
ISO 4379:2018(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 4379:2018(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Dimensions and tolerances . 1
5 Material . 5
6 Surface finish . 5
7 Construction . 6
8 Quality assurance . 6
9 Designation . 6
Bibliography . 7
© ISO 2018 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 4379:2018(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: www .iso .org/iso/foreword .html.
This document was prepared by Technical Committee ISO/TC 123, Plain bearings, Subcommittee SC 3,
Dimensions, tolerances and construction details.
This third edition cancels and replaces the second edition (ISO 4379:1993), of which it constitutes a
minor revision. The changes compared to the previous edition are as follows:
— In Clause 2, all dated references have been changed to undated ones.
— A new Clause 3 Terms and definitions has been added.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/members .html.
iv © ISO 2018 – All rights reserved
---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 4379:2018(E)
Plain bearings — Copper alloy bushes
1 Scope
This document specifies dimensions and tolerances for cylindrical and flanged bushes with internal
diameter, d , in the range 6 mm to 200 mm.
1
It applies to solid mono-metal copper alloy bushes to be used as plain bearings with and without oil
holes and oil grooves.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 1302, Geometrical Product Specifications (GPS) — Indication of surface texture in technical product
documentation
ISO 2768-1, General tolerances — Part 1: Tolerances for linear and angular dimensions without individual
tolerance indications
ISO 4382-1, Plain bearings — Copper alloys — Part 1: Cast copper alloys for solid and multilayer thick-
walled plain bearings
ISO 4382-2, Plain bearings — Copper alloys — Part 2: Wrought copper alloys for solid plain bearings
3 Terms and definitions
No terms and definitions are listed in this document.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https: //www .iso .org/obp
— IEC Electropedia: available at http: //www .electropedia .org/
4 Dimensions and tolerances
Dimensions shall be as shown and given in Figure 1 and in Table 1 and Table 2.
Tolerances shall be as given in Table 3.
Tolerance classes which deviate from those given in this document shall in each case be added
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.