Small craft - Stability and buoyancy assessment and categorization - Part 1: Non-sailing boats of hull length greater than or equal to 6 m (ISO 12217-1:2015)

ISO 12217-1:2015 specifies methods for evaluating the stability and buoyancy of intact (i.e. undamaged) boats. The flotation characteristics of boats susceptible to swamping are also encompassed.
The evaluation of stability and buoyancy properties using this part of ISO 12217 will enable the boat to be assigned to a design category (A, B, C or D) appropriate to its design and maximum total load.
ISO 12217-1:2015 is principally applicable to boats propelled by human or mechanical power of 6 m up to 24 m hull length. However, it can also be applied to boats of under 6 m if they do not attain the desired design category specified in ISO 12217‑3 and they are decked and have quick-draining recesses which comply with ISO 11812.
In relation to habitable multihulls, ISO 12217-1:2015 includes assessment of susceptibility to inversion, definition of viable means of escape and requirements for inverted flotation.
ISO 12217-1:2015 excludes:
inflatable and rigid-inflatable boats covered by ISO 6185, except for references made in ISO 6185 to specific clauses of ISO 12217;
personal watercraft covered by ISO 13590 and other similar powered craft;
gondolas and pedalos;
sailing surfboards;
surfboards, including powered surfboards;
hydrofoils and hovercraft when not operating in the displacement mode; and
submersibles.
ISO 12217-1:2015 does not include or evaluate the effects on stability of towing, fishing, dredging or lifting operations, which need to be separately considered if appropriate.

Kleine Wasserfahrzeuge - Stabilitäts- und Auftriebsbewertung und Kategorisierung - Teil 1: Nicht-Segelboote ab 6 m Rumpflänge (ISO 12217-1:2015)

Dieser Teil von ISO 12217 legt Verfahren für die Beurteilung von Stabilität und Auftrieb von intakten (d. h. unbeschädigten) Booten fest. Ebenfalls sind darin die Auftriebseigenschaften solcher Boote erfasst, die anfällig gegen Vollschlagen sind.
Die Beurteilung der Stabilitäts- und Auftriebseigenschaften nach diesem Teil von ISO 12217 erlaubt es, dem Boot eine Entwurfskategorie (A, B, C, oder D) zuzuordnen, die seiner Auslegung und seiner maximalen Beladung entspricht.
Dieser Teil der ISO 12217 ist grundsätzlich auf Boote in einem Bereich von 6 m bis 24 m Rumpflänge, die durch Muskelkraft oder Motor angetrieben werden, anwendbar. Er kann jedoch auch auf Boote von weniger als 6 m Rumpflänge angewendet werden, wenn diese bei Anwendung von ISO 12217-3 nicht die gewünschte Entwurfskategorie erreichen, jedoch voll gedeckt sind und schnell-lenzende Rezesse entsprechend ISO 11812 besitzen.
In Bezug auf bewohnbare Mehrrumpfboote beinhaltet dieser Teil von ISO 12217 die Bewertung der Anfälligkeit gegen Kenterung, die Definition funktionsfähiger Fluchtmöglichkeiten und Anforderungen an die Schwimm¬fähigkeit im gekenterten Zustand (kieloben).
Ausgeschlossen von der Anwendung dieses Teils von ISO 12217 sind:
—   Schlauchboote und Schlauchboote mit festem Rumpf (RIB) nach ISO 6185 mit Ausnahme der Verweisungen, die sich in jener Norm auf bestimmte Abschnitte in ISO 12217 beziehen;
—   Wassermotorräder nach ISO 13590 und andere, ähnlich angetriebene Wasserfahrzeuge;
—   Gondeln und Tretboote;
—   Segel-Surfbretter;
—   Surfbretter, einschließlich motorisierte Surfbretter;
—   Tragflügelboote und Luftkissenfahrzeuge, sofern sie nicht im Verdrängermodus betrieben werden;
—   Tauchfahrzeuge.
ANMERKUNG   Verdrängermodus bedeutet, dass das Boot nur durch hydrostatische Kräfte getragen wird.
Dieser Teil von ISO 12217 enthält keine Angaben oder Beurteilungen zu den die Stabilität betreffenden Auswirkungen von Schleppen, Fischen, Baggern oder Kranarbeiten; diese müssen, falls erforderlich, gesondert berücksichtigt werden.

Petits navires - Évaluation et catégorisation de la stabilité et de la flottabilité - Partie 1: Bateaux à propulsion non vélique d'une longueur de coque supérieure ou égale à 6 m (ISO 12217-1:2015)

L'ISO 12217-1:2015 spécifie les méthodes d'évaluation de la stabilité et de la flottabilité des bateaux à l'état intact (c'est-à-dire non endommagés). Les caractéristiques de flottabilité des bateaux susceptibles d'envahissement sont également comprises.
L'évaluation des propriétés de stabilité et de flottabilité faite en utilisant l'ISO 12217-1:2015 permettra d'attribuer à un bateau une catégorie de conception (A, B, C ou D) appropriée à sa conception et à sa charge maximale.
L'ISO 12217-1:2015 est principalement applicable aux bateaux propulsés par l'énergie humaine ou une énergie mécanique, d'une longueur de coque de 6 m à 24 m compris. Elle peut, cependant, être également appliquée aux bateaux de moins de 6 m, s'ils n'atteignent pas la catégorie de conception désirée en appliquant l'ISO 12217-3, et s'ils sont pontés et munis de cavités rapidement autovideuses conformes à l'ISO 11812.
Pour ce qui concerne les multicoques habitables, l'ISO 12217-1:2015 comprend l'évaluation de la susceptibilité à l'inversion, la définition d'un moyen d'échappée viable et les exigences de flottabilité à l'état inversé.
L'ISO 12217-1:2015 exclut:
les bateaux pneumatiques et semi-rigides couverts par l'ISO 6185, excepté lorsque l'ISO 6185 fait référence à des paragraphes spécifiques de l'ISO 12217;
les véhicules nautiques à moteur (motos aquatiques), couverts par l'ISO 13590 et engins à moteur similaires;
les gondoles et pédalos;
les planches à voiles;
les planches de surf, y compris les planches motorisées;
les hydrofoils et les bateaux stabilisés par des plans porteurs lorsqu'ils ne sont pas en mode à déplacement; et
les submersibles.
L'ISO 12217-1:2015 n'inclut ni n'évalue les effets sur la stabilité provenant du remorquage, de la pêche, du dragage ou d'opérations de levage, qui doivent être, si nécessaire, considérés séparément.

Mala plovila - Stabilnost in ocena vzgona ter kategorizacija - 1. del: Čolni razen jadrnic s trupom, večjim ali enakim 6 m (ISO 12217-1:2015)

Ta del standarda ISO 12217 določa metode za oceno stabilnosti in vzgona brezhibnih (nepoškodovanih) čolnov. Zajete so tudi značilnosti plovnosti čolnov, ki so izpostavljeni zalivanju. Ocena značilnosti stabilnosti in vzgona z uporabo tega dela standarda ISO 12217 bo omogočila, da bo čoln vključen v konstrukcijsko kategorijo (A, B, C ali D), ki je ustrezna glede na konstrukcijo in največjo skupno obremenitev. Ta del standarda ISO 12217 se uporablja predvsem za čolne, ki jih poganja človek ali stroj, z dolžino trupa od 6 m do 24 m. Uporablja se lahko tudi za čolne, krajše od 6 m, če niso razvrščeni v želeno konstrukcijsko kategorijo, določeno v standardu ISO 12217-3, ter imajo krov in žlebove za hitro odvodnjavanje, ki so v skladu s standardom ISO 11812.
V povezavi z večtrupnimi bivalnimi plovili ta del standarda ISO 12217 vključuje oceno izpostavljenosti prevrnitvi, navedbo ustreznih možnosti umika in zahteve za plovnost v prevrnjenem stanju.
Ta del standarda ISO 12217 izključuje:
– napihljive čolne in napihljive čolne, ki imajo v spodnjem delu trupa togo enoto, ki jih obravnava standard ISO 6185, razen pri sklicih iz standarda ISO 6185 na določene točke standarda ISO 12217;
– osebna plovila, ki jih obravnava standard ISO 13590, in druga podobna plovila na pogon;
– gondole in čolne na pedala;
– jadralne deske;
– deske, vključno z deskami na motorni pogon;
– hidrogliserje in plovila na zračno blazino, kadar ne delujejo v načinu izpodriva; ter
– plovila, ki lahko plujejo pod vodno gladino.
OPOMBA: Pri načinu izpodriva na čoln delujejo le hidrostatične sile. Ne vključuje ali ne vrednoti vpliva na stabilnost pri vlečenju, ribolovu, črpanju ali dvigovanju, pri katerih je treba ustreznost stabilnosti obravnavati posamezno.

General Information

Status
Withdrawn
Publication Date
17-Nov-2015
Withdrawal Date
26-Sep-2017
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
27-Sep-2017

Relations

Buy Standard

Standard
EN ISO 12217-1:2016 - BARVE
English language
87 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 12217-1:2016
01-marec-2016
1DGRPHãþD
SIST EN ISO 12217-1:2013
0DODSORYLOD6WDELOQRVWLQRFHQDY]JRQDWHUNDWHJRUL]DFLMDGHOýROQLUD]HQ
MDGUQLFVWUXSRPYHþMLPDOLHQDNLPP ,62
Small craft - Stability and buoyancy assessment and categorization - Part 1: Non-sailing
boats of hull length greater than or equal to 6 m (ISO 12217-1:2015)
Kleine Wasserfahrzeuge - Stabilitäts- und Auftriebsbewertung und Kategorisierung - Teil
1: Nicht-Segelboote ab 6 m Rumpflänge (ISO 12217-1:2015)
Petits navires - Évaluation et catégorisation de la stabilité et de la flottabilité - Partie 1:
Bateaux à propulsion non vélique d'une longueur de coque supérieure ou égale à 6 m
(ISO 12217-1:2015)
Ta slovenski standard je istoveten z: EN ISO 12217-1:2015
ICS:
47.080 ýROQL Small craft
SIST EN ISO 12217-1:2016 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 12217-1:2016

---------------------- Page: 2 ----------------------

SIST EN ISO 12217-1:2016


EN ISO 12217-1
EUROPEAN STANDARD

NORME EUROPÉENNE

November 2015
EUROPÄISCHE NORM
ICS 47.080 Supersedes EN ISO 12217-1:2013
English Version

Small craft - Stability and buoyancy assessment and
categorization - Part 1: Non-sailing boats of hull length
greater than or equal to 6 m (ISO 12217-1:2015)
Petits navires - Évaluation et catégorisation de la Kleine Wasserfahrzeuge - Stabilitäts- und
stabilité et de la flottabilité - Partie 1: Bateaux à Auftriebsbewertung und Kategorisierung - Teil 1:
propulsion non vélique d'une longueur de coque Nicht-Segelboote ab 6 m Rumpflänge (ISO 12217-
supérieure ou égale à 6 m (ISO 12217-1:2015) 1:2015)
This European Standard was approved by CEN on 10 July 2015.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 12217-1:2015 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 12217-1:2016
EN ISO 12217-1:2015 (E)
Contents Page
European foreword . 3
Annex ZA (informative) Relationship between this European Standard and the essential
requirements of Directive 2013/53/EU aimed to be covered . 4

2

---------------------- Page: 4 ----------------------

SIST EN ISO 12217-1:2016
EN ISO 12217-1:2015 (E)
European foreword
This document (EN ISO 12217-1:2015) has been prepared by Technical Committee ISO/TC 188 “Small
craft”.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by May 2016, and conflicting national standards shall be
withdrawn at the latest by May 2016.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
This document supersedes EN ISO 12217-1:2013.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this
document.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria,
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.