EN ISO 10675-2:2017
(Main)Non-destructive testing of welds - Acceptance levels for radiographic testing - Part 2: Aluminium and its alloys (ISO 10675-2:2017)
Non-destructive testing of welds - Acceptance levels for radiographic testing - Part 2: Aluminium and its alloys (ISO 10675-2:2017)
ISO 10675-2:2017 specifies acceptance levels for indications from imperfections in aluminium butt welds detected by radiographic testing. If agreed, the acceptance levels can be applied to other types of welds or materials.
The acceptance levels can be related to welding standards, application standards, specifications or codes. ISO 10675-2assumes that the radiographic testing has been carried out in accordance with ISO 17636‑1 for RT-F (F = film) or ISO 17636‑2 for RT-S (S = radioscopy) and RT-D (D = digital detectors).
When assessing whether a weld meets the requirements specified for a weld quality level, the sizes of imperfections permitted by standards are compared with the dimensions of indications revealed by a radiograph made of the weld.
Zerstörungsfreie Prüfung von Schweißverbindungen - Zulässigkeitsgrenzen für die Durchstrahlungsprüfung - Teil 2: Aluminium und seine Legierungen (ISO 10675-2:2017)
Essais non destructifs des assemblages soudés - Niveaux d'acceptation pour l'évaluation par radiographie - Partie 2: Aluminium et ses alliages (ISO 10675-2:2017)
L'ISO 10675-2:2017 spécifie les niveaux d'acceptation pour les indications des défauts dans les assemblages soudés en aluminium détectés par contrôle radiographique. En fonction des accords passés, les niveaux d'acceptation peuvent être appliqués à d'autres types d'assemblages soudés ou de matériaux.
Les niveaux d'acceptation peuvent être reliés à des normes de soudage, des normes d'application, des spécifications ou des codes. L'ISO 10675-2 présume que le contrôle par radiographie a été exécuté conformément à l'ISO 17636‑1 pour RT-F (F = film) ou à l'ISO 17636‑2 pour RT-S (S = radioscopie) et RT-D (D = détecteurs numériques).
Pour vérifier qu'une soudure satisfait aux exigences spécifiées pour un niveau de qualité de soudure, les dimensions des défauts permises par les normes sont comparées aux dimensions des indications révélées par la radiographie de la soudure.
Neporušitveno preskušanje zvarnih spojev - Stopnje sprejemljivosti pri radiografiji - 2. del: Aluminij in njegove zlitine (ISO 10675-2:2017)
Ta dokument določa stopnje sprejemljivosti za označevanje na podlagi nepravilnosti v aluminijevih soležnih zvarih, ki se zaznajo z radiografijo. V primeru dogovora se lahko stopnje sprejemljivosti uporabljajo za druge vrste zvarov ali materialov.
Stopnje sprejemljivosti se lahko nanašajo na standarde varjenja, standarde uporabe, specifikacije ali oznake. V tem dokumentu je predpostavljeno, da je bilo radiografsko preskušanje izvedeno skladno s standardom ISO 17636-1 za RT-F (F = film) ali ISO 17636-2 za RT-S (S = radioskopija) in RT-D (D = digitalni detektorji).
Pri ocenjevanju, ali zvar ustreza zahtevam, ki so določene za raven kakovosti zvara, se število nepravilnosti, ki jih dovoljujejo standardi, primerja z dimenzijami oznak, ki jih razkrije radiografska slika zvara.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-marec-2018
1DGRPHãþD
SIST EN ISO 10675-2:2013
Neporušitveno preskušanje zvarnih spojev - Stopnje sprejemljivosti pri radiografiji
- 2. del: Aluminij in njegove zlitine (ISO 10675-2:2017)
Non-destructive testing of welds - Acceptance levels for radiographic testing - Part 2:
Aluminium and its alloys (ISO 10675-2:2017)
Zerstörungsfreie Prüfung von Schweißverbindungen - Zulässigkeitsgrenzen für die
Durchstrahlungsprüfung - Teil 2: Aluminium und seine Legierungen (ISO 10675-2:2017)
Essais non destructifs des assemblages soudés - Niveaux d'acceptation pour
l'évaluation par radiographie - Partie 2: Aluminium et ses alliages (ISO 10675-2:2017)
Ta slovenski standard je istoveten z: EN ISO 10675-2:2017
ICS:
25.160.40 Varjeni spoji in vari Welded joints and welds
77.120.10 Aluminij in aluminijeve zlitine Aluminium and aluminium
alloys
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 10675-2
EUROPEAN STANDARD
NORME EUROPÉENNE
November 2017
EUROPÄISCHE NORM
ICS 25.160.40 Supersedes EN ISO 10675-2:2013
English Version
Non-destructive testing of welds - Acceptance levels for
radiographic testing - Part 2: Aluminium and its alloys (ISO
10675-2:2017)
Essais non destructifs des assemblages soudés - Zerstörungsfreie Prüfung von Schweißverbindungen -
Niveaux d'acceptation pour l'évaluation par Zulässigkeitsgrenzen für die Durchstrahlungsprüfung -
radiographie - Partie 2: Aluminium et ses alliages (ISO Teil 2: Aluminium und seine Legierungen (ISO 10675-
10675-2:2017) 2:2017)
This European Standard was approved by CEN on 31 October 2017.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10675-2:2017 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 10675-2:2017) has been prepared by Technical Committee ISO/TC 44 “Welding
and allied processes” in collaboration with Technical Committee CEN/TC 121 “Welding and allied
processes” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by May 2018, and conflicting national standards shall be
withdrawn at the latest by May 2018.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 10675-2:2013.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 10675-2:2017 has been approved by CEN as EN ISO 10675-2:2017 without any
modification.
INTERNATIONAL ISO
STANDARD 10675-2
Second edition
2017-09
Non-destructive testing of welds —
Acceptance levels for radiographic
testing —
Part 2:
Aluminium and its alloys
Essais non destructifs des assemblages soudés — Niveaux
d'acceptation pour l'évaluation par radiographie —
Partie 2: Aluminium et ses alliages
Reference number
ISO 10675-2:2017(E)
©
ISO 2017
ISO 10675-2:2017(E)
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved
ISO 10675-2:2017(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Radiographic technique . 1
5 General . 2
6 Acceptance levels . 2
Annex A (informative) Guide to the limitations of radiographic testing . 5
Annex B (informative) Examples for determination of percentage (%) of imperfections .6
Annex C (informative) Sums of acceptable areas . 8
Bibliography .10
ISO 10675-2:2017(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 44, Welding and allied processes,
Subcommittee SC 5, Testing and inspection of welds.
This second edition cancels and replaces the first edition (ISO 10675-2:2010), of which it constitutes a
minor revision and contains the following main changes:
— the normative references have been updated;
— Table 1 has been split into two separate tables.
Request for official interpretations of any aspect of this document should be directed to the Secretariat
of ISO/TC 44/SC 5 via your national standards body. A complete listing of these bodies can be found at
www.iso.org.
iv © ISO 2017 – All rights reserved
INTERNATIONAL STANDARD ISO 10675-2:2017(E)
Non-destructive testing of welds — Acceptance levels for
radiographic testing —
Part 2:
Aluminium and its alloys
1 Scope
This document specifies acceptance levels for indications from imperfections in aluminium butt welds
detected by radiographic testing. If agreed, the acceptance levels can be applied to other types of welds
or materials.
The acceptance levels can be related to welding standards, application standards, specifications or
codes. This document assumes that the radiographic testing has been carried out in accordance with
ISO 17636-1 for RT-F (F = film) or ISO 17636-2 for RT-S (S = radioscopy) and RT-D (D = digital detectors).
When assessing whether a weld meets the requirements specified for a weld quality level, the sizes of
imperfections permitted by standards are compared with the dimensions of indications revealed by a
radiograph made of the weld.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 6520-1, Welding and allied processes — Classification of geometric imperfections in metallic
materials — Part 1: Fusion welding
ISO 10042, Welding — Arc-welded joints in aluminium and its alloys — Quality levels for imperfections
ISO 17636-1, Non-destructive testing of welds — Radiographic testing — Part 1: X- and gamma-ray
techniques with film
ISO 17636-2, Non-destructive testing of welds — Radiographic testing — Part 2: X- and gamma-ray
techniques with digital detectors
3 Terms and definitions
No terms and definitions are listed in this document.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at http://www.iso.org/obp
— IEC Electropedia: available at http://www.electropedia.org/
4 Radiographic technique
Depending on the weld quality level, radiographic technique A or B in accordance with ISO 17636-1 shall
be used for RT-F as shown in Table 1 and radiographic technique A or B in accordance with ISO 17636-2
shall be used for RT-S or RT-D as shown in Table 2.
ISO 10675-2:2017(E)
Table 1 — Radiographic testing for RT-F
Testing techniques and classes
Quality levels in accordance Acceptance levels in accordance
in accordance with ISO 17636-1
with ISO 10042 with this document
a
for RT-F
B B 1
a,b
C B 2
D A 3
a
RT-F = Radiographic testing with film
b
However, the minimum number of exposure for circumferential weld testing may correspond to the requirements of
class A of ISO 17636-1.
Table 2 — Radiographic testing for RT-S and RT-D
Testing techniques and classes
Quality levels in accordance Acceptance levels in accordance
in accordance with ISO 17636-2
with ISO 10042 with this document
a b
for RT-S and RT-D
B B 1
c
C B 2
D A 3
a
RT-S = Radioscopic testing
b
RT-D = Radiographic testing with digital detectors
c
However, the minimum number of exposure for circumferential weld testing may correspond to the requirements of
class A of ISO 17636-2.
5 General
Welded joints should be visually tested in accorda
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.