EN ISO 15296:2018
(Main)Gas welding equipment - Vocabulary (ISO 15296:2017)
Gas welding equipment - Vocabulary (ISO 15296:2017)
ISO 15296:2017 defines a vocabulary of terms and definitions specifically related to gas welding equipment.
NOTE In addition to terms used in two of the official ISO languages (English and French), this document gives the equivalent terms in German. These are published under the responsibility of the member body for Germany (DIN) and are given for information only. Only the terms and definitions given in the official languages can be considered as ISO terms.
Gasschweißgeräte - Begriffe (ISO 15296:2017)
Matériel de soudage aux gaz - Vocabulaire (ISO 15296:2017)
ISO 15296:2017 constitue un vocabulaire des termes et définitions spécifiques au matériel de soudage aux gaz.
NOTE En complément des termes en anglais et français (deux des trois langues officielles de l'ISO), la présente Norme internationale donne les termes équivalents en allemand. Ces termes sont publiés sous la responsabilité du comité membre allemand (DIN) et sont donnée au titre d'information seulement. Toutefois, seuls les termes et définitions donnés dans les langues officielles peuvent être considérés comme étant des termes de l'ISO.
Oprema za plamensko varjenje - Slovar (ISO 15296:2017)
Ta standard vključuje nabor tehničnih izrazov in definicij, ki se nanašajo posebej na plinsko opremo za varjenje.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-marec-2018
1DGRPHãþD
SIST EN 13622:2003
Oprema za plamensko varjenje - Slovar (ISO 15296:2017)
Gas welding equipment - Vocabulary (ISO 15296:2017)
Gasschweißgeräte - Begriffe (ISO 15296:2017)
Matériel de soudage aux gaz - Vocabulaire (ISO 15296:2017)
Ta slovenski standard je istoveten z: EN ISO 15296:2018
ICS:
01.040.25 Izdelavna tehnika (Slovarji) Manufacturing engineering
(Vocabularies)
25.160.30 Varilna oprema Welding equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 15296
EUROPEAN STANDARD
NORME EUROPÉENNE
January 2018
EUROPÄISCHE NORM
ICS 01.040.25; 25.160.30 Supersedes EN 13622:2002
English Version
Gas welding equipment - Vocabulary (ISO 15296:2017)
Mat?iel de soudage aux gaz - Vocabulaire (ISO Gasschwei?ger?e - Begriffe (ISO 15296:2017)
15296:2017)
This European Standard was approved by CEN on 16 November 2017.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15296:2018 E
worldwide for CEN national Members.
Contents
Page
European foreword . 3
European foreword
This document (EN ISO 15296:2018) has been prepared by Technical Committee ISO/TC 44 “Welding
and allied processes” in collaboration with Technical Committee CEN/TC 121 “Welding and allied
processes” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by July 2018, and conflicting national standards shall be
withdrawn at the latest by July 2018.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 13622:2002.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 15296:2017 has been approved by CEN as EN ISO 15296:2018 without any modification.
INTERNATIONAL ISO
STANDARD 15296
NORME
Second edition
Seconde édition
INTERNATIONALE
2017-09
Gas welding equipment — Vocabulary
Matériel de soudage aux gaz —
Vocabulaire
Gasschweißgeräte — Terminologie
Reference number
Numéro de référence
ISO 15296:2017(E/F/D)
©
ISO 2017
ISO 15296:2017(E/F/D)
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2017, Published in Switzerland/Publié en Suisse
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite ni utilisée
sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie, l’affichage sur
l’internet ou sur un Intranet, sans autorisation écrite préalable. Les demandes d’autorisation peuvent être adressées à l’ISO à
l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved/Tous droits réservés
ISO 15296:2017(E/F/D)
Foreword .iv
Avant-propos .v
Vorwort .vi
Introduction .vii
Introduction .viii
Einleitung .ix
1 Scope . 1
1 Domaine d'application . 1
1 Anwendungsbereich . 1
2 Normative references . 1
2 Références normatives . 1
2 Normative Verweise . 1
3 Terms and definitions . 2
3.1 Group 1 — Terms relating to hoses, hose assemblies and assembled hoses . 2
3.2 Group 2 — Terms relating to pressure . 3
3.3 Group 3 — Terms relating to blowpipes . 4
3.4 Group 4 — Terms relating to safety devices . 7
3.5 Group 5 — Specific terms . 9
3 Termes et définitions . 2
3.1 Groupe 1 — Termes relatifs aux tuyaux souples, embouts et tuyaux souples équipés . 2
3.2 Groupe 2 — Termes relatifs à la pression . 3
3.3 Groupe 3 — Termes relatifs aux chalumeaux . 4
3.4 Groupe 4 — Termes relatifs aux dispositifs de sécurité . 7
3.5 Groupe 5 — Termes spécifiques . 9
3 Begriffe und Definitionen. 2
3.1 Gruppe 1 — Begriffe für Schläuche, Schlaucheinbindungen und Schlauchleitungen . 2
3.2 Gruppe 2 — Begriffe für Druck . 3
3.3 Gruppe 3 — Begriffe für Brenner . 4
3.4 Gruppe 4 — Begriffe für Sicherheitseinrichtungen . 7
3.5 Gruppe 5 — Spezielle Begriffe . 9
Alphabetical index .11
Index alphabétique.12
Alphabetisches Stichwortverzeichnis .13
ISO 15296:2017(E/F/D)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the WTO
principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary
information
This document was prepared by Technical Committee ISO/TC 44, Welding and allied processes,
Subcommittee SC 8, Equipment for gas welding, cutting and allied processes.
This second edition cancels and replaces the first edition (ISO 15296:2004), which has been technically
revised and contains the following changes:
— the title has been simplified;
— the definitions of
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.