EN 983:1996+A1:2008
(Main)Safety of machinery - Safety requirements for fluid power systems and their components - Pneumatics
Safety of machinery - Safety requirements for fluid power systems and their components - Pneumatics
This standard applies to pneumatic systems and their components on machinery. It identifies hazards and factors which affect the safety of systems and their components when they are put to their intended use.
Gas bottles and receivers are excluded from the scope of this standard. For receivers see EN 286-1.
The principles specified apply to the design, construction and modification of new systems and their components and aspects of use including:
- Assembly
- Installation
- Adjustment
- Operation
- Cleaning
- Maintenance.
Components are covered in the standard but only to the extent that safety requirements are given to allow the components to be safely integrated into a system's design.
The standard applies to systems and their components on machinery that are manufactured after the date of the adoption of this standard.
Sicherheit von Maschinen - Sicherheitstechnische Anforderungen an fluidtechnische Anlagen und deren Bauteile - Pneumatik
Diese Norm gilt für pneumatische Anlagen und Bauteile in Maschinen. Sie benennt Gefährdungen und Faktoren, die die Sicherheit der Anlagen und deren Bauteile beeinflussen, wenn diese in der beabsichtigten Weise verwendet werden.
Gasflaschen und Luftbehälter sind vom Anwendungsbereich dieser Norm ausgenommen. Für Luftbehälter siehe EN 286-1.
Die festgelegten Prinzipien gelten für die Konstruktion, den Bau und die Modifizierung von neuen Anlagen und deren Bauteile und für Aspekte der Anwendung, die
- Montage,
- Einbau,
- Einrichtung,
- Betrieb,
- Reinigung,
- Instandhaltung
einschließen.
Bauteile sind in dieser Norm berücksichtigt, aber nur in dem Maße, wie sicherheitstechnische Anforderungen gestellt werden, die es erlauben, die Bauteile sicher in die Auslegung einer Anlage einzubeziehen.
Die Norm gilt für Anlagen und deren Bauteile in Maschinen, die nach dem Zeitpunkt der Annahme dieser Norm hergestellt werden.
Sécurité des machines - Prescriptions de sécurité relatives aux systèmes et leurs composants de transmissions hydrauliques et pneumatiques - Pneumatique
La présente norme européenne s'applique aux systèmes pneumatiques et à leurs composants intégrés aux machines. Elle identifie les risques et les facteurs qui affectent la sécurité des systèmes et de leurs composants placés dans les conditions d’utilisation prévues.
Les bouteilles à gaz et les réservoirs sont exclus du domaine d'application de la présente norme. Pour les réservoirs, voir EN 286-1.
Les principes énoncés traitent de la conception, de la construction et de la modification des nouveaux systèmes et leurs composants et des aspects d'utilisation, incluant :
assemblage ;
installation ;
réglage ;
fonctionnement ;
nettoyage ;
maintenance.
Les composants sont traités dans la norme mais seulement dans la limite où les prescriptions de sécurité sont données pour permettre aux composants d'être intégrés de façon sûre dans la conception des systèmes.
La norme s'applique aux systèmes et à leurs composants intégrés aux machines qui seront fabriqués après son adoption.
Varnost strojev - Varnostne zahteve za fluidne sisteme in njihove komponente - Pnevmatika
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-november-2008
Varnost strojev - Varnostne zahteve za fluidne sisteme in njihove komponente -
Pnevmatika
Safety of machinery - Safety requirements for fluid power systems and their components
- Pneumatics
Sicherheit von Maschinen - Sicherheitstechnische Anforderungen an fluidtechnische
Anlagen und deren Bauteile - Pneumatik
Sécurité des machines - Prescriptions de sécurité relatives aux systèmes et leurs
composants de transmissions hydrauliques et pneumatiques - Pneumatique
Ta slovenski standard je istoveten z: EN 983:1996+A1:2008
ICS:
23.100.01 +LGUDYOLþQLVLVWHPLQDVSORãQR Fluid power systems in
general
23.140 .RPSUHVRUMLLQSQHYPDWLþQL Compressors and pneumatic
VWURML machines
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN 983:1996+A1
NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2008
ICS 23.100.01; 23.140 Supersedes EN 983:1996
English Version
Safety of machinery - Safety requirements for fluid power
systems and their components - Pneumatics
Sécurité des machines - Prescriptions de sécurité relatives Sicherheit von Maschinen - Sicherheitstechnische
aux systèmes et leurs composants de transmissions Anforderungen an fluidtechnische Anlagen und deren
hydrauliques et pneumatiques - Pneumatique Bauteile - Pneumatik
This European Standard was approved by CEN on 11 March 1996 and includes Amendment 1 approved by CEN on 27 July 2008.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 983:1996+A1:2008: E
worldwide for CEN national Members.
Contents Page
Foreword.3
Introduction .4
1 Scope.4
2 Normative references.5
3 Definitions.6
4 List of hazards.7
5 Safety requirements and/or measures .9
5.1 Basic requirements for the design and specification of pneumatic systems.9
5.2 Additional requirements.10
5.2.1 Site conditions.10
5.2.2 Component removal.10
5.2.3 Preparation for transportation.11
5.3 Specific requirements for components and controls .11
5.3.1 Motors and rotary actuators .11
5.3.2 Cylinders.11
5.3.3 Valves.12
5.3.4 Energy transmission and conditioning .13
5.3.5 System protection.15
5.3.6 Sequence control.16
5.3.7 Control systems with servo or proportional valves.16
5.3.8 Silencers.16
6 Verification of safety requirements and/or measures.16
6.1 Inspection.16
6.2 Testing.17
7 Information for use .17
7.1 Final data.17
7.2 Maintenance data.17
7.3 Marking.17
7.3.1 Components.17
7.3.2 Components within a system.18
7.3.3 Ports.18
7.3.4 Valve control mechanisms .18
7.3.5 Internal devices.18
Annex A (informative) Bibliography .19
Annex ZA (informative) !Relationship between this European Standard and the Essential
Requirements of EU Directive 98/37/EC".21
Annex ZB (informative) !Relationship between this European Standard and the Essential
Requirements of EU Directive 2006/42/EC".22
Foreword
This document (EN 983:1996+A1:2008) has been prepared by Technical Committee CEN/TC 114 “Safety of
machinery”, the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by March 2009, and conflicting standards shall be withdrawn at the latest
by December 2009.
This document includes Amendment 1, approved by CEN on 2008-07-27.
This document supersedes EN 983:1996.
The start and finish of text introduced or altered by amendment is indicated in the text by tags ! ".
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
!For relationship with EU Directive(s), see informative Annexes ZA and ZB, which are integral parts of this
document."
It was developed to contribute towards unification of safety regulations and procedures in the various member
countries for each aspect dealt within the field of pneumatics for fluid power systems and their components.
This Standard utilizes the most recently validated technical information from established technical sources
(e.g. CEN, ISO, national standards and European documents).
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and United Kingdom.
Introduction
This standard is a type B2 standard (according to EN 292-1) and contains the general requirements for
pneumatic systems and their components on machinery. For type C standard makers, it is a basis for the
development of specific requirements on dedicated machines. If no type C standards are available, it is a
basis for the manufacturers when constructing machines that include pneumatic systems and their
components.
In developing this standard, safety related requirements out of ISO 4414 were selected as well as additional
safety related requirements.
Equivalent safety requirements for hydraulic systems are defined in EN 982 "Safety of machinery – Safety
requirements for fluid power systems and their components – Hydraulics".
1 Scope
This standard applies to pneumatic systems and their components on machinery. It identifies hazards and
factors which affect the safety of systems and their components when they are put to their intended use.
Gas bottles and receivers are excluded from the scope of this standard. For receivers see EN 286-1.
The principles specified apply to the design, construction and modification of new systems and their
components and aspects of use including:
Assembly
Installation
Adjustment
Operation
Cleaning
Maintenance.
Components are covered in the standard but only to the extent that safety requirements are given to allow the
components to be safely integrated into a system's design.
The standard applies to systems and their components on machinery that are manufactured after the date of
the adoption of this standard.
2 Normative references
This European Standard incorporates by dated or undated reference, provisions from other publications.
These normative references are cited at the appropriate places in the text and the publications are listed
hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to
this European Standard only when incorporated in it by amendment or revision. For undated references the
latest edition of the publication referred to applies.
EN 286-1, Simple unfired pressure vessels designed to contain air or nitrogen – Part 1: Design, manufacture
and testing.
EN 292-1:1991, Safety of machinery - Basic concepts, general principles for design — Part 1: Basic
terminology, methodology.
EN 292-2:1991, Safety of machinery - Basic concepts, general principles for design — Part 2: Technical
principles and specifications.
EN 418, Safety of machinery – Emergency stop equipment, functional aspects – Principles for design.
prEN 954-1:1992, Safety of machinery - Safety related parts of control systems — Part 1: General principles
for design.
prEN 1050:1992, Safety of machinery - Risk assessment.
ENV 1070, Safety of machinery – Terminology.
prEN 1127-1:1993, Safety of machinery – Fire and explosions – Part 1: Explosion prevention and protection.
EN 50081-2, Electromagnetic compatibility – Generic emission standard – Part 2: Industrial environment.
prEN 50082-2:1994, Electromagnetic compatibility – Generic immunity standard – Part 2: Industrial
environment.
EN 60204-1:1992, Safety of machinery - Electrical equipment of machines – Part 1: General requirements
(IEC 204-1:1992, modified).
EN 60529, Degrees of protection provided by enclosures (IP code) (IEC 529:1989).
ISO 1219-1, Fluid power systems and components – Graphic symbols and circuit diagrams – Part 1: Graphic
symbols.
ISO/DIS 1219-2:1993, Fluid power systems and components – Graphic symbols and circuit diagrams – Part 2:
Circuit diagrams.
ISO 5598, Fluid power systems and components - Vocabulary.
ISO/TR 11688-1, Acoustics – Recommended practice for the design of low-noise machinery and equipment –
Part 1: Planning.
3 Definitions
For the purpose of this standard, the definitions of ENV 1070 and the following apply. Other definitions not
included are given in ISO 5598.
3.1
fluid power
the means whereby signals and energy ca
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.