EN ISO 11299-1:2013

Plastics piping systems for renovation of underground gas supply networks - Part 1: General (ISO 11299-1:2011)

This part of ISO 11299 specifies the requirements and test methods for plastics piping systems for use in the
renovation of underground gas supply networks. It is applicable to pipes and fittings as manufactured, as well as
to the installed lining system. It is not applicable to sprayed coatings, the existing pipeline or any annular filler.
This part of ISO 11299 establishes the general requirements common to all relevant renovation techniques.

Kunststoff-Rohrleitungssysteme für die Renovierung von erdverlegten Gasversorgungsnetzwerken - Teil 1: Allgemeines (ISO 11299-1:2011)

Dieser Teil von ISO 11299 legt die Anforderungen und Prüfverfahren für Kunststoff-Rohrleitungssysteme fest, die für die Renovierung von erdverlegten Gasversorungsnetzwerken verwendet werden. Sie gilt sowohl für vorgefertigte Rohre und Formstücke, als auch für das eingebaute Lining-System. Diese Norm gilt nicht für aufgespritzte Beschichtungen, die bestehenden Rohrleitungen oder Ringraumverfüllungen.
Dieser Teil von ISO 11299 legt die allgemeinen Anforderungen an alle maßgeblichen Renovierungstechniken fest.

Systèmes de canalisations en plastique pour la rénovation des réseaux de gaz enterrés - Partie 1: Généralités (ISO 11299-1:2011)

Cevni sistemi iz polimernih materialov za obnovo podzemnih omrežij za oskrbo s plinom - 1. del: Splošno (ISO 11299-1:2011)

Ta del standarda ISO 11299 določa zahteve in preskusne metode za cevne sisteme iz polimernih materialov za uporabo pri obnovi podzemnih omrežij za oskrbo s plinom. Uporablja se za cevi in fitinge, kot so izdelani, ter za nameščene sisteme oblaganja. Ne uporablja se za razpršene obloge, obstoječe cevovode ali kakršno koli obročasto polnilo. Ta del standarda ISO 11299 določa splošne zahteve, ki so skupne vsem ustreznim tehnikam obnove.

General Information

• Status: Withdrawn
• Publication Date: 19-Feb-2013
• Withdrawal Date: 04-Dec-2018
• ICS: 23.040.20 - Plastics pipes
• ICS: 23.040.45 - Plastics fittings
• ICS: 75.200 - Petroleum products and natural gas handling equipment
• Technical Committee: CEN/TC 155 - Plastics piping systems and ducting systems
• Drafting Committee: CEN/TC 155/WG 17 - Plastic components for the use of renovation of piping systems
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Completion Date: 05-Dec-2018
• Ref Project: SIST EN ISO 11299-1:2013 - Plastics piping systems for renovation of underground gas supply networks - Part 1: General (ISO 11299-1:2011)

Relations

• Replaces: EN 14408-1:2004 - Plastics piping systems for renovation of underground gas supply networks - Part 1: General
• Effective Date: 02-May-2012
• Replaced By: EN ISO 11299-1:2018 - Plastics piping systems for renovation of underground gas supply networks - Part 1: General (ISO 11299-1:2018)
• Effective Date: 25-Nov-2015

Standards Content (Sample)

SLOVENSKI STANDARD
01-april-2013
1DGRPHãþD
SIST EN 14408-1:2005
Cevni sistemi iz polimernih materialov za obnovo podzemnih omrežij za oskrbo s
plinom - 1. del: Splošno (ISO 11299-1:2011)
Plastics piping systems for renovation of underground gas supply networks - Part 1:
General (ISO 11299-1:2011)
Kunststoff-Rohrleitungssysteme für die Renovierung von erdverlegten
Gasversorgungsnetzwerken - Teil 1: Allgemeines (ISO 11299-1:2011)
Systèmes de canalisations en plastique pour la rénovation des réseaux de gaz enterrés -
Partie 1: Généralités (ISO 11299-1:2011)
Ta slovenski standard je istoveten z: EN ISO 11299-1:2013
ICS:
83.140.30 Cevi, fitingi in ventili iz Plastics pipes, fittings and
polimernih materialov valves
91.140.40 Sistemi za oskrbo s plinom Gas supply systems
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 11299-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
February 2013
ICS 23.040.20; 23.040.45; 75.200 Supersedes EN 14408-1:2004
English Version
Plastics piping systems for renovation of underground gas
supply networks - Part 1: General (ISO 11299-1:2011)
Systèmes de canalisations en plastique pour la rénovation Kunststoff-Rohrleitungssysteme für die Renovierung von
des réseaux de gaz enterrés - Partie 1: Généralités (ISO erdverlegten Gasversorgungsnetzwerken - Teil 1:
11299-1:2011) Allgemeines (ISO 11299-1:2011)
This European Standard was approved by CEN on 5 February 2013.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2013 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11299-1:2013: E
worldwide for CEN national Members.

Contents Page
Foreword .3

Foreword
The text of ISO 11299-1:2011 has been prepared by Technical Committee ISO/TC 138 “Plastics pipes, fittings
and valves for the transport of fluids” of the International Organization for Standardization (ISO) and has been
taken over as EN ISO 11299-1:2013 by Technical Committee CEN/TC 155 “Plastics piping systems and
ducting systems” the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by August 2013, and conflicting national standards shall be withdrawn at
the latest by August 2013.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 14408-1:2004.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 11299-1:2011 has been approved by CEN as EN ISO 11299-1:2013 without any modification.
INTERNATIONAL  ISO
STANDARD 11299-1
First edition
2011-09-15
Plastics piping systems for renovation of
underground gas supply networks
Part 1:
General
Systèmes de canalisations en plastique pour la rénovation des réseaux
de gaz enterrés — Partie 1: Généralités
Reference number
ISO 11299-1:2011(E)
©
ISO 2011
ISO 11299-1:2011(E)
©  ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland
ii © ISO 2011 – All rights reserved

ISO 11299-1:2011(E)
Contents Page
Foreword . v
Introduction .vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
3.1 General . 1
3.2 Techniques . 3
3.3 Characteristics . 4
3.4 Materials . 5
3.5 Product stages . 5
3.6 Service conditions . 6
4 Symbols and abbreviated terms . 6
4.1 Symbols . 6
4.2 Abbreviated terms . 6
5 Pipes at the “M” stage . 6
5.1 Materials . 6
5.2 General characteristics . 6
5.3 Material characteristics . 7
5.4 Geometric characteristics . 7
5.5 Mechanical characteristics . 7
5.6 Physical characteristics . 7
5.7 Jointing . 7
5.8 Marking . 7
6 Fittings at the “M” stage . 7
6.1 Materials . 7
6.2 General characteristics . 8
6.3 Material characteristics . 8
6.4 Geometric characteristics . 8
6.5 Mechanical characteristics . 8
6.6 Physical characteristics . 8
6.7 Jointing . 8
6.8 Marking . 8
7 Ancillary components . 8
8 Fitness for purpose of the installed lining system at the “I” stage . 9
8.1 Materials . 9
8.2 General characteristics . 9
8.3 Material characteristics . 9
8.4 Geometric characteristics . 9
8.5 Mechanical characteristics . 9
8.6 Physical characteristics .10
8.7 Additional characteristics .10
8.8 Sampling .10
9 Installation practice .10
9.1 Preparatory work .10
9.2 Storage, handling and transport of pipes and fittings .10
9.3 Equipment .10
9.4 Installation . 11
9.5 Process-related inspection and testing . 11
9.6 Lining termination . 11
9.7 Reconnecting to the existing pipeline system .12
9.8 Transfer of service lines .12
© ISO 2011 – All rights reserved  iii

ISO 11299-1:2011
...