iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN ISO 9697:2017

(Main)

Water quality - Gross beta activity in non-saline water - Test method using thick source (ISO 9697:2015)

Water quality - Gross beta activity in non-saline water - Test method using thick source (ISO 9697:2015)

ISO 9697:2015 specifies a test method for the determination of gross beta activity concentration in non-saline waters. The method covers non-volatile radionuclides with maximum beta energies of approximately 0,3 MeV or higher. Measurement of low energy beta emitters (e.g. 3H, 228Ra, 210Pb, 14C, 35S, and 241Pu) and some gaseous or volatile radionuclides (e.g. radon and radioiodine) might not be included in the gross beta quantification using the test method described in ISO 9697:2015.
This test method is applicable to the analysis of raw and drinking waters. The range of application depends on the amount of total soluble salts in the water and on the performance characteristics (background count rate and counting efficiency) of the counter used. It is the laboratory's responsibility to ensure the suitability of this method for the water samples tested.

Wasserbeschaffenheit - Bestimmung der Gesamt-Beta-Aktivität in nicht-salzhaltigem Wasser - Dickschichtverfahren (ISO 9697:2015)

Qualité de l'eau - Activité bêta globale des eaux non salines - Méthode d'essai par source concentrée (ISO 9697:2015)

L'ISO 9697:2015 spécifie une méthode d'essai permettant de déterminer l'activité volumique bêta globale des eaux non salines. La méthode couvre les radionucléides non volatils émetteurs bêta avec des énergies maximales d'environ 0,3 MeV ou plus élevées. Les mesurages des émetteurs bêta à faible énergie (par exemple, 3H, 228Ra, 210Pb, 14C, 35S et 241Pu) et de certains radionucléides gazeux ou volatils (par exemple, radon et iode radioactif) peuvent ne pas être inclus dans la quantification bêta globale en utilisant la méthode d'essai décrite dans l'ISO 9697:2015.
Cette méthode d'essai est applicable à l'analyse des eaux brutes et potables. La gamme d'application dépend de la quantité de sels solubles totaux dans l'eau et des caractéristiques de performance (taux de comptage du bruit de fond et efficacité de comptage) du compteur utilisé. Il incombe au laboratoire de s'assurer de l'adéquation de cette méthode pour les échantillons d'eau soumis à essai.

Kakovost vode - Skupna beta aktivnost v neslanih vodah - Preskusna metoda robustnega vira (ISO 9697:2015)

Ta mednarodni standard opisuje metodo za določevanje skupne beta aktivnosti v neslanih vodah. Metoda zajema nehlapne beta oddajne radionuklide z maks. beta energijo > 0,3 MeV. Ta standard ne vključuje merjenja beta oddajnikov z zelo nizko energijo, npr.3H, 14C, 35S in 241Pu. Ta metoda se uporablja za analizo neobdelane in pitne vode.

General Information

Status
Withdrawn
Publication Date
13-Jun-2017
Withdrawal Date
18-Jun-2019
ICS
13.060.60 - Examination of physical properties of water
13.280 - Radiation protection
17.240 - Radiation measurements
Technical Committee
CEN/TC 230 - Water analysis
Drafting Committee
CEN/TC 230 - Water analysis
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
19-Jun-2019
Ref Project
SIST EN ISO 9697:2017 - Water quality - Gross beta activity in non-saline water - Test method using thick source (ISO 9697:2015)

Relations

Replaced By
EN ISO 9697:2019 - Water quality - Gross beta activity - Test method using thick source (ISO 9697:2018)
Effective Date
26-Jun-2019

Buy Standard

EN ISO 9697:2017EN ISO 9697:2017
PreviousNext
Standard
EN ISO 9697:2017
English language
20 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 9697:2017
01-december-2017
Kakovost vode - Skupna beta aktivnost v neslanih vodah - Preskusna metoda
robustnega vira (ISO 9697:2015)
Water quality - Gross beta activity in non-saline water - Test method using thick source
(ISO 9697:2015)
Wasserbeschaffenheit - Bestimmung der Gesamt-Beta-Aktivität in nicht-salzhaltigem
Wasser - Dickschichtverfahren (ISO 9697:2015)
Qualité de l'eau - Activité bêta globale des eaux non salines - Méthode d'essai par
source concentrée (ISO 9697:2015)
Ta slovenski standard je istoveten z: EN ISO 9697:2017
ICS:
13.060.60 Preiskava fizikalnih lastnosti Examination of physical
vode properties of water
17.240 Merjenje sevanja Radiation measurements
SIST EN ISO 9697:2017 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 9697:2017

---------------------- Page: 2 ----------------------

SIST EN ISO 9697:2017


EN ISO 9697
EUROPEAN STANDARD

NORME EUROPÉENNE

June 2017
EUROPÄISCHE NORM
ICS 13.280; 13.060.60
English Version

Water quality - Gross beta activity in non-saline water -
Test method using thick source (ISO 9697:2015)
Qualité de l'eau - Activité bêta globale des eaux non Wasserbeschaffenheit - Bestimmung der Gesamt-Beta-
salines - Méthode d'essai par source concentrée (ISO Aktivität in nicht-salzhaltigem Wasser -
9697:2015) Dickschichtverfahren (ISO 9697:2015)
This European Standard was approved by CEN on 27 May 2016.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 9697:2017 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 9697:2017
EN ISO 9697:2017 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 9697:2017
EN ISO 9697:2017 (E)
European foreword
The text of ISO 9697:2015 has been prepared by Technical Committee ISO/TC 147 “Water quality” of
the International Organization for Standardization (ISO) and has been taken over as EN ISO 9697:2017
by Technical Committee CEN/TC 230 “Water analysis” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by December 2017, and conflicting national standards
shall be withdrawn at the latest by December 2017.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 9697:2015 has been approved by CEN as EN ISO 9697:2017 without any modification.


3

---------------------- Page: 5 ----------------------

SIST EN ISO 9697:2017

---------------------- Page: 6 ----------------------

SIST EN ISO 9697:2017
INTERNATI
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 13164-4:2023(Main)
Water quality - Radon-222 - Part 4: Test method using two-phase liquid scintillation counting (ISO 13164-4:2023)
SIST EN ISO 13164-4:2023

This document describes a test method for the determination of radon-222 (222Rn) activity concentration in non-saline waters by extraction and liquid scintillation counting.
The 222Rn activity concentrations, which can be measured by this test method utilizing currently available instruments, are above 0,5 Bq·l−1 which is the typical detection limit for a 10 ml test sample and a measuring time of 1 h.
It is the responsibility of the laboratory to ensure the validity of this test method for water samples of untested matrices.
Annex A gives indication on the necessary counting conditions to meet the required detection limits for drinking water monitoring.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 22017:2020(Main)
Water quality - Guidance for rapid radioactivity measurements in nuclear or radiological emergency situation (ISO 22017:2020)
SIST EN ISO 22017:2021

This document provides guidelines for testing laboratories wanting to use rapid test methods on water samples that may be contaminated following a nuclear or radiological emergency incident. In an emergency situation, consideration should be given to:
—     taking into account the specific context for the tests to be performed, e.g. a potentially high level of contamination;
—     using or adjusting, when possible, radioactivity test methods implemented during routine situations to obtain a result rapidly or, for tests not performed routinely, applying specific rapid test methods previously validated by the laboratory, e.g. for 89Sr determination;
—     preparing the test laboratory to measure a large number of potentially contaminated samples.
The aim of this document is to ensure decision makers have reliable results needed to take actions quickly and minimize the radiation dose to the public.
Measurements are performed in order to minimize the risk to the public by checking the quality of water supplies. For emergency situations, test results are often compared to operational intervention levels.
NOTE    Operational intervention levels (OILs) are derived from IAEA Safety Standards[8] or national authorities[9].
A key element of rapid analysis can be the use of routine methods but with a reduced turnaround time. The goal of these rapid measurements is often to check for unusual radioactivity levels in the test sample, to identify the radionuclides present and their activity concentration levels and to establish compliance of the water with intervention levels[10][11][12]. It should be noted that in such circumstances, validation parameters evaluated for routine use (e.g. reproducibility, precision, etc.) may not be applicable to the modified rapid method. However, due to the circumstances arising after an emergency, the modified method may still be fit-for-purpose although uncertainties associated with the test results need to be evaluated and may increase from routine analyses.
The first steps of the analytical approach are usually screening methods based on gross alpha and gross beta test methods (adaptation of ISO 10704 and ISO 11704) and gamma spectrometry (adaptation of ISO 20042, ISO 10703 and ISO 19581). Then, if required[13], test method standards for specific radionuclides (see Clause 2) are adapted and applied (for example, 90Sr measurement according to ISO 13160) as proposed in Annex A.
This document refers to published ISO documents. When appropriate, this document also refers to national standards or other publicly available documents.
Screening techniques that can be carried out directly in the field are not part of this document.

  • Standard
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 13164-3:2020(Main)
Water quality - Radon-222 - Part 3: Test method using emanometry (ISO 13164-3:2013)
SIST EN ISO 13164-3:2020

ISO 13164-3:2013 specifies a test method for the determination of radon-222 activity concentration in a sample of water following its transfer from the aqueous phase to the air phase by degassing and its detection. It gives recommendations for rapid measurements performed within less than 1 h.
The radon-222 activity concentrations, which can be measured by this test method utilizing currently available instruments, range from 0,1 Bq l−1 to several hundred thousand becquerels per litre for a 100 ml test sample.
This test method is used successfully with drinking water samples. The laboratory is responsible for ensuring the validity of this test method for water samples of untested matrices.
This test method can be applied on field sites or in the laboratory.
Annexes A and B give indications on the necessary counting conditions to meet the required sensitivity for drinking water monitoring

  • Standard
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 13164-2:2020(Main)
Water quality - Radon-222 - Part 2: Test method using gamma-ray spectrometry (ISO 13164-2:2013)
SIST EN ISO 13164-2:2020

ISO 13164-2:2013 specifies a test method for the determination of radon-222 activity concentration in a sample of water following the measurement of its short-lived decay products by direct gamma-spectrometry of the water sample.
The radon-222 activity concentrations, which can be measured by this test method utilizing currently available gamma-ray instruments, range from a few becquerels per litre to several hundred thousand becquerels per litre for a 1 l test sample.
This test method can be used successfully with drinking water samples. The laboratory is responsible for ensuring the validity of this test method for water samples of untested matrices.
An annex gives indications on the necessary counting conditions to meet the required sensitivity for drinking water monitoring.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 13164-1:2020(Main)
Water quality - Radon-222 - Part 1: General principles (ISO 13164-1:2013, Correction version 2013-11-15)
SIST EN ISO 13164-1:2020

ISO 13164-1:2013 gives general guidelines for sampling, packaging, and transporting of all kinds of water samples, for the measurement of the activity concentration of radon-222.
The test methods fall into two categories: a) direct measurement of the water sample without any transfer of phase (see ISO 13164‑2); b) indirect measurement involving the transfer of the radon-222 from the aqueous phase to another phase (see ISO 13164‑3).
The test methods can be applied either in the laboratory or on site.
The laboratory is responsible for ensuring the suitability of the test method for the water samples tested.

  • Standard
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 22908:2020(Main)
Water quality - Radium 226 and Radium 228 - Test method using liquid scintillation counting (ISO 22908:2020)
SIST EN ISO 22908:2020

This document specifies the determination of radium-226 (226Ra) and radium-228 (228Ra) activity concentrations in drinking water samples by chemical separation of radium and its measurement using liquid scintillation counting.
Massic activity concentrations of 226Ra and 228Ra which can be measured by this test method utilizing currently available liquid scintillation counters go down to 0,01 Bq/kg for 226Ra and 0,06 Bq/kg for 228Ra for a 0,5 kg sample mass and a 1 h counting time in a low background liquid scintillation counter[8].
The test method can be used for the fast detection of contamination of drinking water by radium in emergency situations.

  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 9697:2019(Main)
Water quality - Gross beta activity - Test method using thick source (ISO 9697:2018)
SIST EN ISO 9697:2019

This document specifies a test method for the determination of gross beta activity concentration in non-saline waters. The method covers non-volatile radionuclides with maximum beta energies of approximately 0,3 MeV or higher. Measurement of low energy beta emitters (e.g. 3H, 228Ra, 210Pb, 14C, 35S and 241Pu) and some gaseous or volatile radionuclides (e.g. radon and radioiodine) might not be included in the gross beta quantification using the test method described in this document.
This test method is applicable to the analysis of raw and drinking waters. The range of application depends on the amount of total soluble salts in the water and on the performance characteristics (background count rate and counting efficiency) of the counter used.
It is the laboratory's responsibility to ensure the suitability of this method for the water samples tested.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 13164-4:2023(Main)
Water quality - Radon-222 - Part 4: Test method using two-phase liquid scintillation counting (ISO 13164-4:2023)
SIST EN ISO 13164-4:2023

This document describes a test method for the determination of radon-222 (222Rn) activity concentration in non-saline waters by extraction and liquid scintillation counting.
The 222Rn activity concentrations, which can be measured by this test method utilizing currently available instruments, are above 0,5 Bq·l−1 which is the typical detection limit for a 10 ml test sample and a measuring time of 1 h.
It is the responsibility of the laboratory to ensure the validity of this test method for water samples of untested matrices.
Annex A gives indication on the necessary counting conditions to meet the required detection limits for drinking water monitoring.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 22017:2020(Main)
Water quality - Guidance for rapid radioactivity measurements in nuclear or radiological emergency situation (ISO 22017:2020)
SIST EN ISO 22017:2021

This document provides guidelines for testing laboratories wanting to use rapid test methods on water samples that may be contaminated following a nuclear or radiological emergency incident. In an emergency situation, consideration should be given to:
—     taking into account the specific context for the tests to be performed, e.g. a potentially high level of contamination;
—     using or adjusting, when possible, radioactivity test methods implemented during routine situations to obtain a result rapidly or, for tests not performed routinely, applying specific rapid test methods previously validated by the laboratory, e.g. for 89Sr determination;
—     preparing the test laboratory to measure a large number of potentially contaminated samples.
The aim of this document is to ensure decision makers have reliable results needed to take actions quickly and minimize the radiation dose to the public.
Measurements are performed in order to minimize the risk to the public by checking the quality of water supplies. For emergency situations, test results are often compared to operational intervention levels.
NOTE    Operational intervention levels (OILs) are derived from IAEA Safety Standards[8] or national authorities[9].
A key element of rapid analysis can be the use of routine methods but with a reduced turnaround time. The goal of these rapid measurements is often to check for unusual radioactivity levels in the test sample, to identify the radionuclides present and their activity concentration levels and to establish compliance of the water with intervention levels[10][11][12]. It should be noted that in such circumstances, validation parameters evaluated for routine use (e.g. reproducibility, precision, etc.) may not be applicable to the modified rapid method. However, due to the circumstances arising after an emergency, the modified method may still be fit-for-purpose although uncertainties associated with the test results need to be evaluated and may increase from routine analyses.
The first steps of the analytical approach are usually screening methods based on gross alpha and gross beta test methods (adaptation of ISO 10704 and ISO 11704) and gamma spectrometry (adaptation of ISO 20042, ISO 10703 and ISO 19581). Then, if required[13], test method standards for specific radionuclides (see Clause 2) are adapted and applied (for example, 90Sr measurement according to ISO 13160) as proposed in Annex A.
This document refers to published ISO documents. When appropriate, this document also refers to national standards or other publicly available documents.
Screening techniques that can be carried out directly in the field are not part of this document.

  • Standard
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 13164-3:2020(Main)
Water quality - Radon-222 - Part 3: Test method using emanometry (ISO 13164-3:2013)
SIST EN ISO 13164-3:2020

ISO 13164-3:2013 specifies a test method for the determination of radon-222 activity concentration in a sample of water following its transfer from the aqueous phase to the air phase by degassing and its detection. It gives recommendations for rapid measurements performed within less than 1 h.
The radon-222 activity concentrations, which can be measured by this test method utilizing currently available instruments, range from 0,1 Bq l−1 to several hundred thousand becquerels per litre for a 100 ml test sample.
This test method is used successfully with drinking water samples. The laboratory is responsible for ensuring the validity of this test method for water samples of untested matrices.
This test method can be applied on field sites or in the laboratory.
Annexes A and B give indications on the necessary counting conditions to meet the required sensitivity for drinking water monitoring

  • Standard
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day