CEN/TS 16892:2015

Plastics - Welding of thermoplastics - Specification of welding procedures

This Technical Specification provides guidance for the minimum content of welding procedure specifications for the following welding processes:
-   hot gas welding: round nozzle, high speed nozzle, wedge;
-   extrusion welding;
-   heated tool welding: butt, socket, wedge;
-   solvent welding: socket;
-   electrofusion welding: socket, saddle.
This Technical Specification applies to the welding of the following products and semi-finished products made of thermoplastic materials:
-   sheet;
-   pipe;
-   fittings;
-   lining membrane.

Kunststoffe - Schweißen von thermoplastischen Kunststoffen - Anforderung an Schweißverfahren

Diese Technische Spezifikation enthält Hinweise zu den Mindestangaben von Schweißanweisungen für folgende Schweißverfahren:
   Warmgasschweißen: Runddüse, Schnellschweißdüse, Breitschlitzdüse;
   Extrusionsschweißen;
   Heizelementschweißen: Stumpfstoß, Muffe, Breitschlitzdüse;
   Quellschweißen: Muffe;
   Heizwendelschweißen: Muffe, Sattel.
Diese Technische Spezifikation gilt für das Schweißen folgender Produkte und Halbzeuge aus thermoplastischen Materialien:
   Tafeln;
   Rohre;
   Formstücke;
   Dichtungsbahnen.

Plastiques - Soudage des matériaux termoplastiques - Spécification de modes opératoires de soudage

Polimerni materiali - Varjenje plastomerov - Specifikacija varilnih postopkov

Ta tehnična specifikacija podaja smernice glede minimalne vsebine v specifikacijah postopkov varjenja za naslednje postopke varjenja:
– varjenje z vročim plinom: okrogla šoba, šoba za hitro varjenje, klini;
– ekstrudersko varjenje;
– varjenje z vročimi ploščami: soležni zvari, obojni zvari, klini;
– varjenje s topilom: obojni zvari;
– elektrofuzijsko varjenje: obojni zvari;
Ta tehnična specifikacija se uporablja za varjenje naslednjih izdelkov in polizdelkov iz plastomernih materialov:
– plošče;
– cevi;
– spojniki;
– obložne membrane

General Information

• Status: Published
• Publication Date: 15-Dec-2015
• ICS: 25.160.10 - Welding processes
• Technical Committee: CEN/TC 249 - Plastics
• Drafting Committee: CEN/TC 249/WG 16 - Welding of thermoplastics
• Current Stage: 9093 - Decision to confirm - Review Enquiry
• Completion Date: 14-Mar-2022
• Ref Project: SIST-TS CEN/TS 16892:2016 - Plastics - Welding of thermoplastics - Specification of welding procedures

Standards Content (Sample)

SLOVENSKI STANDARD
SIST-TS CEN/TS 16892:2016
01-marec-2016
Polimerni materiali - Varjenje plastomerov - Specifikacija varilnih postopkov
Plastics - Welding of thermoplastics - Specification of welding procedures
Kunststoffe - Schweißen von thermoplastischen Kunststoffen - Anforderung von
Schweißverfahren
Plastiques - Soudage des matériaux termoplastiques - Spécification de modes
opératoires de soudage
Ta slovenski standard je istoveten z: CEN/TS 16892:2015
ICS:
25.160.10 Varilni postopki in varjenje Welding processes
83.080.01 Polimerni materiali na Plastics in general
splošno
SIST-TS CEN/TS 16892:2016 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST-TS CEN/TS 16892:2016

---------------------- Page: 2 ----------------------

SIST-TS CEN/TS 16892:2016


CEN/TS 16892
TECHNICAL SPECIFICATION

SPÉCIFICATION TECHNIQUE

December 2015
TECHNISCHE SPEZIFIKATION
ICS 25.160.10
English Version

Plastics - Welding of thermoplastics - Specification of
welding procedures
Plastiques - Soudage des matériaux termoplastiques - Kunststoffe - Schweißen von thermoplastischen
Spécification de modes opératoires de soudage Kunststoffen - Anforderung von Schweißverfahren
This Technical Specification (CEN/TS) was approved by CEN on 13 November 2015 for provisional application.

The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to
submit their comments, particularly on the question whether the CEN/TS can be converted into a European Standard.

CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS
available promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in
parallel to the CEN/TS) until the final decision about the possible conversion of the CEN/TS into an EN is reached.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TS 16892:2015 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST-TS CEN/TS 16892:2016
CEN/TS 16892:2015 (E)
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Technical content of welding procedure specification (WPS) . 5
4.1 General . 5
4.2 Related to the welding organization . 5
4.3 Related to the parent material(s) . 5
4.3.1 Parent material(s) type . 5
4.3.2 Parent material(s) dimensions . 6
4.4 Common to all welding procedures. 6
4.4.1 Joint preparation . 6
4.4.2 Welding process .
...