Thermal spraying - Powders - Part 1: Characterization and technical supply conditions (ISO 14232-1:2017)

ISO 14232-1:2017 specifies measuring methods for the characterization of powders and their technical supply conditions. It is applicable to powders that are used in thermal spraying on the basis of their physical and chemical properties.

Thermisches Spritzen - Pulver - Teil 1: Zusammensetzung und technische Lieferbedingungen (ISO 14232-1:2017)

Dieses Dokument gilt für Pulver, die gegenwärtig aufgrund ihrer physikalischen und chemischen Eigenschaften beim thermischen Spritzen verwendet werden. Dieses Dokument legt die Messverfahren zur Charakterisierung von Pulvern und deren technische Lieferbedingungen fest.

Projection thermique - Poudres - Partie 1:Caractérisation et conditions techniques de livraison (ISO 14232-1:2017)

ISO 14232-1:2017 spécifie des méthodes de mesure permettant de caractériser les poudres et les conditions techniques de livraison de celles-ci. Il s'applique aux poudres utilisées en projection thermique sur la base de leurs propriétés physiques et chimiques.

Vroče brizganje - Prah - 1. del: Lastnosti in tehnični pogoji za dobavo (ISO 14232-1:2017)

Ti standardi zajemajo praške, ki se trenutno uporabljajo pri vročem brizganju.

General Information

Status
Published
Publication Date
25-Apr-2017
Withdrawal Date
30-Oct-2017
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
26-Apr-2017
Due Date
31-Oct-2016
Completion Date
26-Apr-2017

Relations

Buy Standard

Standard
EN ISO 14232-1:2017
English language
18 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-julij-2017
1DGRPHãþD
SIST EN 1274:2004
9URþHEUL]JDQMH3UDKGHO/DVWQRVWLLQWHKQLþQLSRJRML]DGREDYR ,62

Thermal spraying - Powders - Part 1: Characterisation and technical supply conditions
(ISO 14232-1:2017)
Thermisches Spritzen - Pulver - Teil 1: Zusammensetzung und technische
Lieferbedingungen (ISO 14232-1:2017)
Projection thermique - Poudres - Partie 1: Caractérisation et conditions techniques de
livraison (ISO 14232-1:2017)
Ta slovenski standard je istoveten z: EN ISO 14232-1:2017
ICS:
25.220.20 Površinska obdelava Surface treatment
77.160 Metalurgija prahov Powder metallurgy
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 14232-1
EUROPEAN STANDARD
NORME EUROPÉENNE
April 2017
EUROPÄISCHE NORM
ICS 25.220.20 Supersedes EN 1274:2004
English Version
Thermal spraying - Powders - Part 1: Characterization and
technical supply conditions (ISO 14232-1:2017)
Projection thermique - Poudres - Partie 1: Thermisches Spritzen - Pulver - Teil 1:
Caractérisitation et conditions techniques de livraison Zusammensetzung und technische Lieferbedingungen
(ISO 14232-1:2017) (ISO 14232-1:2017)
This European Standard was approved by CEN on 2 April 2017.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 14232-1:2017 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
European foreword
This document (EN ISO 14232-1:2017) has been prepared by Technical Committee ISO/TC 107
“Metallic and other inorganic coatings” in collaboration with Technical Committee CEN/TC 240
“Thermal spraying and thermally sprayed coatings” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by October 2017, and conflicting national standards shall
be withdrawn at the latest by October 2017.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
This document supersedes EN 1274:2004.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 14232-1:2017 has been approved by CEN as EN ISO 14232-1:2017 without any
modification.
INTERNATIONAL ISO
STANDARD 14232-1
First edition
2017-03
Thermal spraying — Powders —
Part 1:
Characterization and technical supply
conditions
Projection thermique — Poudres —
Partie 1: Caractérisitation et conditions techniques de livraison
Reference number
ISO 14232-1:2017(E)
©
ISO 2017
ISO 14232-1:2017(E)
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved

ISO 14232-1:2017(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Properties and property determination of powders for thermal spraying .1
4.1 Sampling and sample splitting . 1
4.2 Chemical composition . 2
4.3 Particle size range — Particle size distribution . 2
4.4 Manufacturing process — Particle shape . 3
4.5 Apparent density . 3
4.6 Flowability . 3
4.7 Microstructure . 4
4.8 Determination and composition of phases . 4
4.9 Summary . 4
5 Classification of powders . 4
6 Powder identification and designation . 4
7 Conditions of supply . 4
8 Certificate . 5
Annex A (informative) Powder shape and morphologies . 6
Bibliography . 9
ISO 14232-1:2017(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO’s adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: w w w . i s o .org/ iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 107, Metallic and other inorganic coatings.
This first edition of ISO 14232-1, together with ISO/TR 14232-2, cancels and replaces ISO 14232:2000.
A list of all parts in the ISO 14232 series can be found on the ISO website.
iv © ISO 2017 – All rights reserved

ISO 14232-1:2017(E)
Introduction
For thermal spray processes that use material in a powder form, the powder can be considered as one
of the main elements requiring control to produce an acceptable coating. The chemical and physical
properties of powder play a fundamental role in the creation of desired coating properties. The size,
shape and morphology of the powder particles determine the melting behaviour and therefore the
processing of powders in general.
To keep the coating properties and the spray process as consistent as possible, it is very important to
maintain all the characteristics of powder particles within limited tolerances.
An exception is granted to details on the properties of sprayed coatings. Such properties, which result
from spraying conditions not covered by this document, e.g. gas composition, deposition efficiency,
material flow rate, stand-off distance, etc., can differ greatly from the properties of the original powder.
The ISO 14232 series consists of two parts. This document examines the characterization of spray
powders. ISO/TR 14232-2 is a technical report that examines how technical literature describes the
application of powders.
INTERNATIONAL STANDARD ISO 14232-1:2017(E)
Thermal spraying — Powders —
Part 1:
Characterization and technical supply conditions
1 Scope
This document specifies measuring methods for the characterization of powders and their technical
supply conditions. It is applicable to powders that are used in thermal spraying on the basis of their
physical and chemical properties.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 3923-2, Metallic powders — Determination of apparent density — Part 2: Scott volumeter
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.