Roofing and cladding products from metal sheet - Specification for self-supporting products of steel, aluminium or stainless steel sheet - Part 1: Steel

This part of EN 508 specifies requirements for self-supporting roofing, covering, wall cladding, lining, liner tray and tile products for discontinuous laying made from metallic coated steel sheet with or without additional organic coatings. Sheets intended to be used with insulation and membranes are also covered.
This document establishes general characteristics, definitions, classifications and labelling for the products, together with requirements for the materials from which the products can be manufactured. It is intended to be used either by manufacturers to ensure that their products comply with the requirements or by purchasers to verify that the products comply when purchased before they are dispatched from the factory. It specifies the requirements for products which enable them to meet all normal service conditions.
This document applies to all discontinuously laid self-supporting external profiled sheets for roofing covering, wall cladding, lining, and liner trays, with the exception of tiles with a surface area less than 1 m2 and produced by stamping. These profiled sheets are designed to keep wind, rain and snow out of the building and to transfer any resultant loads and infrequent maintenance loads to the structure.
This document does not cover products for structural purposes, i.e. it does cover products used in constructions of structural Class III (according to EN 1993-1-3), it does not cover products used in constructions of structural Classes I and II (according to EN 1993-1-3) intended to contribute to the global or partial stability of the building structure by providing racking resistance or resistance to permanent static loads (excluding self-weight of the metal sheet).
No requirements for supporting construction, design of roof, cladding, lining, tile system and execution of connections and flashings are included.

Dachdeckungs- und Wandbekleidungsprodukte aus Metallblech - Spezifikation für selbsttragende Dachdeckungsprodukte aus Stahlblech, Aluminiumblech oder nichtrostendem Stahlblech - Teil 1: Stahl

Dieser Teil von EN 508 legt Anforderungen an selbsttragende Dachdeckungsprodukte, Dachbekleidungs¬produkte, Außenwandbekleidungsprodukte, Fassadenpaneel-, Kassettenprofil  und Dachpfannenprodukte zur überlappenden Verlegung fest, die aus Stahlblech mit metallischem Überzug, mit oder ohne zusätzliche organische Beschichtung, gefertigt wurden. Metallbleche zur Verwendung in Verbindung mit Wärmedämmung und Membranen werden ebenfalls behandelt.
Dieses Dokument legt die allgemeinen Merkmale, Definitionen, Klassifizierungen und die Etikettierung für die Produkte fest sowie die Anforderungen an die Werkstoffe, aus denen die Produkte hergestellt werden können. Es ist dafür bestimmt, entweder vom Hersteller verwendet zu werden, um sicherzustellen, dass seine Produkte den Anforderungen entsprechen, oder vom Käufer, um zu überprüfen, ob die Produkte den Anforderungen entsprechen, bevor sie das Werk verlassen. Es legt die Anforderungen an Produkte fest, unter denen diese allen üblichen Einsatzbedingungen gerecht werden können.
Dieses Dokument ist anzuwenden für alle außen verwendeten, überlappend verlegten, selbsttragenden Profiltafeln für Dachdeckungen, Dachbekleidungen, Außenwandbekleidungen, Fassadenpaneele und Kassettenprofile; es ist nicht anzuwenden für Dachpfannentafeln mit einer Oberfläche < 1 m2 und gepresste Dachpfannen. Diese Profiltafeln sind so ausgelegt, dass sie das Eindringen von Wind, Regen und Schnee in das Gebäude verhindern und dass alle daraus und alle aus nicht ständig durchgeführten Instandhaltungsarbeiten resultierenden Lasten auf das Bauwerk übertragen werden.
Dieses Dokument ist nicht anzuwenden für Produkte für tragende Zwecke, d. h. es gilt für Produkte zur Verwendung in Konstruktionen der Klasse III (nach EN 1993 1 3), es ist nicht anzuwenden für Produkte in Konstruktionen der Klassen I und II (nach EN 1993 1 3), die durch Sicherstellung der Plattenschubfestigkeit bzw. des Widerstandes gegen ständige statische Belastungen (mit Ausnahme des Eigengewichts des Metallblechs) zur globalen oder lokalen Stabilität des Bauwerks beitragen.
Anforderungen an die Unterkonstruktion, an die Konstruktion des Dach , Bekleidungs , Fassaden  bzw. Dachpfannensystems, an die Ausführung der Verbindungen und an Bekleidungsbleche sind nicht Gegenstand dieses Dokuments.

Produits de couverture et de bardage en tôle métallique - Spécification pour les produits autoportants en tôle d'acier, d'aluminium ou d'acier inoxydable - Partie 1 : Acier

La présente partie de l'EN 508 spécifie les exigences relatives aux produits autoportants pour toiture, couverture, bardages extérieur et intérieur et cloisons, plateaux et tuiles pour pose en discontinu, en tôles d'acier revêtues d'un métal, avec ou sans revêtement organique supplémentaire. Les tôles destinées à être utilisées avec une isolation et des membranes sont également couvertes.
Le présent document établit les caractéristiques générales, les définitions, les classifications et l'étiquetage applicables aux produits, de même que les exigences relatives aux matériaux à partir desquels les produits peuvent être fabriqués. Il est destiné à être utilisé soit par des fabricants en vue de démontrer que leurs produits sont conformes aux exigences, soit par des acheteurs pour vérifier que les produits sont conformes avant leur mise à disposition sur le marché, avant leur expédition de l'usine. Il spécifie les exigences relatives aux produits pour leur permettre de répondre à toutes les conditions normales en service.
Le présent document s'applique à toutes les plaques autoportantes nervurées extérieures de couverture, de bardages intérieurs et extérieurs, de cloisons posées en discontinu, à l'exception des tuiles d'une surface inférieure à 1 m² et produites par emboutissage. Ces plaques nervurées sont conçues pour empêcher le vent, la pluie et la neige de pénétrer dans le bâtiment et transmettent à la structure porteuse les charges qui en résultent ainsi que les charges occasionnelles dues aux opérations d'entretien.
Le présent document ne couvre pas les produits pour applications structurelles, c'est-à-dire qu'il couvre les produits utilisés dans la classe structurelle III (selon EN 1993-1-3), il ne couvre pas les produits destinés aux constructions de classes structurelles I et II (selon EN 1993-1-3) destinés à contribuer à la stabilité globale ou partielle de la structure du bâtiment ou apportant un contreventement ou une résistance aux charges statiques permanentes (à l'exclusion du poids propre de la plaque métallique).
Aucune exigence relative à la structure porteuse, à la conception du système de toiture, aux bardages extérieur et intérieur, cloisons, tuiles et à la réalisation des assemblages et des finitions n'est incluse.

Pločevina za pokrivanje streh in oblaganje sten - Specifikacija za samonosilne proizvode iz jeklene, aluminijeve pločevine ali pločevine iz nerjavnega jekla - 1. del: Jeklo

General Information

Status
Published
Publication Date
12-Oct-2021
Withdrawal Date
29-Apr-2022
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
13-Oct-2021
Due Date
18-Aug-2021
Completion Date
13-Oct-2021

Relations

Buy Standard

Standard
EN 508-1:2021
English language
48 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-december-2021
Nadomešča:
SIST EN 508-1:2014
Pločevina za pokrivanje streh in oblaganje sten - Specifikacija za samonosilne
proizvode iz jeklene, aluminijeve pločevine ali pločevine iz nerjavnega jekla - 1.
del: Jeklo
Roofing and cladding products from metal sheet - Specification for self-supporting
products of steel, aluminium or stainless steel sheet - Part 1: Steel
Dachdeckungs- und Wandbekleidungsprodukte aus Metallblech - Spezifikation für
selbsttragende Dachdeckungsprodukte aus Stahlblech, Aluminiumblech oder
nichtrostendem Stahlblech - Teil 1: Stahl
Produits de couverture et de bardage en tôle métallique - Spécification pour les produits
autoportants en tôle d'acier, d'aluminium ou d'acier inoxydable - Partie 1 : Acier
Ta slovenski standard je istoveten z: EN 508-1:2021
ICS:
77.140.50 Ploščati jekleni izdelki in Flat steel products and semi-
polizdelki products
91.060.20 Strehe Roofs
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN 508-1
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2021
EUROPÄISCHE NORM
ICS 91.060.20 Supersedes EN 508-1:2014
English Version
Roofing and cladding products from metal sheet -
Specification for self-supporting products of steel,
aluminium or stainless steel sheet - Part 1: Steel
Produits de couverture et de bardage en tôle Dachdeckungs- und Wandbekleidungsprodukte aus
métallique - Spécification pour les produits Metallblech - Spezifikation für selbsttragende
autoportants en tôle d'acier, d'aluminium ou d'acier Dachdeckungsprodukte aus Stahlblech,
inoxydable - Partie 1 : Acier Aluminiumblech oder nichtrostendem Stahlblech - Teil
1: Stahl
This European Standard was approved by CEN on 21 June 2021.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 508-1:2021 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms, definitions, symbols and abbreviations . 6
3.1 General . 6
3.2 Material definitions . 6
3.3 Profile definitions . 7
3.4 Product geometry . 9
3.5 Symbols and abbreviations .12
4 Requirements .13
4.1 General .13
4.2 Materials .13
4.3 Products .15
5 Test methods .17
5.1 Material properties .17
5.2 Mechanical properties .17
6 Designation.17
7 Marking, labelling and packaging .18
7.1 Marking and labelling .18
7.2 Packaging and special ordering conditions .18
7.3 Transport, storage and handling .18
Annex A (informative) Aluminium coated steel sheet (type A) .19
Annex B (normative) Multilayer coated steel sheet .21
Annex C (informative) Metallic coatings .23
Annex D (normative) Dimensional tolerances .27
Bibliography .48

European foreword
This document (EN 508-1:2021) has been prepared by Technical Committee CEN/TC 128 “Roof covering
products for discontinuous laying and products for wall cladding”, the secretariat of which is held by NBN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2022, and conflicting national standards shall be
withdrawn at the latest by April 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 508-1:2014.
In comparison with EN 508-1:2014 the following technical changes have been made:
— the scope of the document has been extended to include cladding products;
— a reference has been added to ZM (hot dip zinc-magnesium) coating;
— the reference AZ with organic coating has been deleted;
— a bending requirement has been added;
— three grades have been added 390, 420 and 450;
— minimum nominal coating masses have been added for exterior applications;
— clarification of the tolerances about liner tray.
These changes or additions can be found in the following Clauses and subclauses: Clause 1; 3.2.4; 3.2.6;
3.2.7; 3.5; 4.1; 4.2.1; 4.2.2; 4.2.3; 4.3.3.1 and Annex C.
EN 508, Roofing and cladding products from metal sheet - Specification for self-supporting products of steel,
aluminium or stainless steel sheet consists of the following parts:
— Part 1: Steel;
— Part 2: Aluminium;
— Part 3: Stainless steel.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North
Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United
Kingdom.
Introduction
Figure 1 indicates the position of this document in the CEN framework of standards concerning roofing
and cladding products of metal sheet.

Figure 1 — Framework of standards
In this document, the performance of the product has been defined in terms of calculation and a number
of type tests.
The performance of a roof or of the cladding constructed with these products depends not only on the
properties of the product as required by this document, but also on the design, construction and
performance of the roof or the cladding as a whole in relation to the environment and conditions of use.
1 Scope
This part of EN 508 specifies requirements for self-supporting roofing, covering, wall cladding, lining,
liner tray and tile products for discontinuous laying made from metallic coated steel sheet with or without
additional organic coatings. Sheets intended to be used with insulation and membranes are also covered.
This document establishes general characteristics, definitions, classifications and labelling for the
products, together with requirements for the materials from which the products can be manufactured. It
is intended to be used either by manufacturers to ensure that their products comply with the
requirements or by purchasers to verify that the products comply when purchased before they are
dispatched from the factory. It specifies the requirements for products which enable them to meet all
normal service conditions.
This document applies to all discontinuously laid self-supporting external profiled sheets for roofing
covering, wall cladding, lining, and liner trays, with the exception of tiles with a surface area less than
1 m and produced by stamping. These profiled sheets are designed to keep wind, rain and snow out of
the building and to transfer any resultant loads and infrequent maintenance loads to the structure.
This document does not cover products for structural purposes, i.e. it does cover products used in
constructions of structural Class III (according to EN 1993-1-3), it does not cover products used in
constructions of structural Classes I and II (according to EN 1993-1-3) intended to contribute to the
global or partial stability of the building structure by providing racking resistance or resistance to
permanent static loads (excluding self-weight of the metal sheet).
No requirements for supporting construction, design of roof, cladding, lining, tile system and execution
of connections and flashings are included.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 1427, Bitumen and bituminous binders - Determination of the softening point - Ring and Ball method
EN 10143, Continuously hot-dip coated steel sheet and strip - Tolerances on dimensions and shape
EN 10169:2010+A1:2012, Continuously organic coated (coil coated) steel flat products - Technical delivery
conditions
EN 10346, Continuously hot-dip coated steel flat products for cold forming - Technical delivery conditions
EN 14782, Self-supporting metal sheet for roofing, external cladding and internal lining - Product
specification and requirements
EN ISO 6270-1, Paints and varnishes - Determination of resistance to humidity - Part 1: Condensation
(single-sided exposure) (ISO 6270-1)
EN ISO 6988, Metallic and other non-organic coatings - Sulfur dioxide test with general condensation of
moisture (ISO 6988)
EN ISO 9227, Corrosion tests in artificial atmospheres - Salt spray tests (ISO 9227)
3 Terms, definitions, symbols and abbreviations
3.1 General
For the purposes of this document, the terms and definitions given in EN 10169:2010+A1:2012 and the
following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
• ISO Online browsing platform: available at https://www.iso.org/obp
• IEC Electropedia: available at https://www.electropedia.org/
3.1.1
self-supporting product
product which will, by virtue of its material and shape, support all applied loadings (e.g. snow, wind, foot
traffic, insulation, membrane) and transmit these loadings to spaced structural supports
3.1.2
wall
if not otherwise specified, a vertical part of the envelop with a maximum inclination between 30° and 45°
3.1.3
roof
all elements of the envelope not covered by definition of a wall
3.2 Material definitions
3.2.1
hot-dip zinc coated steel sheet, type Z
product obtained by continu
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.