EN 13160-5:2016+A1:2024

Leak detection systems - Part 5: Requirements and test/assessment methods for in-tank gauge systems and pressurised pipework systems

This standard gives requirements and corresponding test\assessment methods applicable to leak detection kits, based upon volumetric loss from within the tank and/or pipework system. The kits usually comprise:
- Measuring Device
- Evaluation Device
- Alarm Device
Intended use:
Leak Detection kits are intended to be used in\with single or double skin underground tanks or single or double skin underground and/or aboveground, pipework designed for flammable liquids having a flash point not exceeding 100 °C.

Leckanzeigesysteme - Teil 5: Anforderungen und Prüf-/Bewertungsmethoden für Tankinhaltsmesssysteme und druckbeaufschlagte Rohrleitungen

Diese Europäische Norm legt Anforderungen an und die einschlägigen Prüf-/Bewertungsmethoden für Leckanzeiger, die auf dem Volumenverlust aus dem Inneren des Tanks und/oder Rohrleitungssystems basieren, fest. Die Systeme bestehen in der Regel aus:
   Messeinrichtung;
   Auswerteeinrichtung;
   Alarmeinrichtung.
Vorgesehener Verwendungszweck:
Leckanzeiger sind für den Einsatz in/mit ein- oder doppel¬wandigen unterirdischen Tanks oder ein- oder doppelwandigen unterirdischen und/oder oberirdischen Rohrleitungen vorgesehen, die für brennbare Flüssigkeiten mit einem Flammpunkt von höchstens 100 °C ausgelegt sind.

Systèmes de détection de fuites - Partie 5: Exigences et méthodes d'essai/d'évaluation des systèmes de détection de fuites en citernes et des systèmes de tuyauterie sous pression

La présente Norme européenne spécifie les exigences et les méthodes d'essai/d'évaluation correspondantes applicables aux kits de détection de fuites, fondées sur la perte volumétrique dans le réservoir et/ou dans le système de tuyauteries. Les kits sont généralement constitués des éléments suivants :
—   Dispositif de mesurage
—   Dispositif d'évaluation
—   Dispositif d'alarme
Usage prévu :
Les kits de détection de fuites sont destinés à être utilisés dans/avec des réservoirs souterrains à simple ou double paroi ou des tuyauteries à simple ou double paroi, souterraines et/ou aériennes, conçus pour des liquides inflammables ayant un point d'éclair inférieur ou égal à 100 °C.

Sistemi za kontrolo tesnosti - 5. del: Zahteve in metode za preskušanje in ocenjevanje sistemov za zaznavanje netesnosti, vgrajenih v rezervoarje in tlačne cevovode (vključno z dopolnilom A1)

General Information

• Status: Published
• Publication Date: 12-Nov-2024
• ICS: 23.020.10 - Stationary containers and tanks
• ICS: 23.040.99 - Other pipeline components
• Technical Committee: CEN/TC 393 - Equipment for storage tanks and for service stations
• Drafting Committee: CEN/TC 393/WG 2 - Leak detecting devices for tanks and pipes
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 13-Nov-2024
• Completion Date: 13-Nov-2024
• Ref Project: SIST EN 13160-5:2016+A1:2025 - Leak detection systems - Part 5: Requirements and test/assessment methods for in-tank gauge systems and pressurised pipework systems

Relations

• Merged From: EN 13160-5:2016 - Leak detection systems - Part 5: Requirements and test/assessment methods for in-tank gauge systems and pressurised pipework systems
• Effective Date: 18-Sep-2024

Standards Content (Sample)

SLOVENSKI STANDARD
01-januar-2025
Nadomešča:
SIST EN 13160-5:2016
Sistemi za kontrolo tesnosti - 5. del: Zahteve in metode za preskušanje in
ocenjevanje sistemov za zaznavanje netesnosti, vgrajenih v rezervoarje in tlačne
cevovode (vključno z dopolnilom A1)
Leak detection systems - Part 5: Requirements and test/assessment methods for in-tank
gauge systems and pressurised pipework systems
Leckanzeigesysteme - Teil 5: Anforderungen und Prüf-/Bewertungsmethoden für
Tankinhaltsmesssysteme und druckbeaufschlagte Rohrleitungen
Systèmes de détection de fuites - Partie 5: Exigences et méthodes d'essai/d'évaluation
des systèmes de détection de fuites en citernes et des systèmes de tuyauterie sous
pression
Ta slovenski standard je istoveten z: EN 13160-5:2016+A1:2024
ICS:
23.020.10 Nepremične posode in Stationary containers and
rezervoarji tanks
23.040.99 Drugi sestavni deli za Other pipeline components
cevovode
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN 13160-5:2016+A1
EUROPEAN STANDARD
NORME EUROPÉENNE
November 2024
EUROPÄISCHE NORM
ICS 23.020.10; 23.040.99 Supersedes EN 13160-5:2016
English Version
Leak detection systems - Part 5: Requirements and
test/assessment methods for in-tank gauge systems and
pressurised pipework systems
Systèmes de détection de fuites - Partie 5: Exigences et Leckanzeigesysteme - Teil 5: Anforderungen und Prüf-
méthodes d'essai/d'évaluation des systèmes de /Bewertungsmethoden für Tankinhaltsmesssysteme
détection de fuites en citernes et des systèmes de und druckbeaufschlagte Rohrleitungen
tuyauterie sous pression
This European Standard was approved by CEN on 8 April 2016 and includes Amendment 1 approved by CEN on 11 September
2024.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13160-5:2016+A1:2024 E
worldwide for CEN national Members.

Contents Page
European foreword . 5
1 Scope . 6
2 Normative references . 6
3 Terms, definitions, symbols and abbreviated terms . 7
3.1 Terms and definitions . 7
3.2 Symbols and abbreviated terms . 7
4 Requirements . 7
4.1 Effectiveness of leak detection kits . 7
4.1.1 General . 7
4.1.2 Electrical or signal cable of the measuring device . 8
4.1.3 Leak detection kit. 8
4.1.4 Measures volumetric loss . 8
4.1.5 Requirements for software . 9
4.1.6 Mechanical construction . 10
4.1.7 Effects of thermal contraction . 10
4.1.8 Alarm device . 10
4.2 Durability of effectiveness . 10
4.2.1 Durability of effectiveness against temperature . 10
4.2.2 Durability of effectiveness against chemical attack . 10
4.2.3 Durability of effectiveness against hydraulic shock (only for measuring devices used
on pressurized line) . 10
4.2.4 Durability of effectiveness against fatigue and mechanical wear\degradation, (only
for measuring devices used on pressurized line) . 10
4.2.5 Durability of effectiveness against microbiological growth on critical surfaces
involved in the measurement process . 10
5 Testing, assessment and sampling methods . 11
5.1 Effectiveness of leak detection kits . 11
5.1.1 General . 11
5.1.2 Disconnection of the electrical or signal cable of the measuring device . 11
5.1.3 Leak detection kit. 11
5.1.4 Measures volumetric loss . 11
5.1.5 Software . 25
5.1.6 Mechanical construction . 25
5.1.7 Effects of thermal contraction . 26
5.1.8 Alarm Device . 26
5.2 Durability of Effectiveness . 26
5.2.1 Durability of effectiveness against temperature . 26
5.2.2 Durability of effectiveness against chemical attack . 26
5.2.3 Durability of effectiveness against hydraulic shock (only for measuring devices used
on pressurized line) . 28
5.2.4 Durability of effectiveness against fatigue and mechanical wear\degradation, (only
for measuring devices used on pressurized line) . 28
5.2.5 Durability of effectiveness against microbiological growth on critical surfaces
involved in the measurement process . 29
6 Assessment and verification of constancy of performance — AVCP . 29
6.1 General . 29
6.2 Type testing . 29
6.2.1 General . 29
6.2.2 Test samples, testing and compliance criteria . 30
6.2.3 Test reports . 31
6.2.4 Shared other party results . 31
6.2.5 Cascading determination of the product type results . 31
6.3 Factory production control (FPC) . 32
6.3.1 General . 32
6.3.2 Requirements . 33
6.3.3 Product specific requirements . 35
6.3.4 Procedure for modifications . 36
6.3.5 One-off products, pre-production products (e.g. prototypes) and products produced
in very low quantity . 36
7 Marking, labelling and packaging . 37
Annex A (normative) Acquisition of field data to provide a standard database for testing
software leak detection systems Category A . 38
A.1 Objective . 38
A.2 Requirements . 39
A.3 Equipment . 40
A.4 Method . 41
A.5 Data up-loading and verification . 43
A.6 Induced leak rates – quantitative systems . 44
A.7 Induced leak rates – qualitative systems . 44
A.8 Test sequence . 44
A.9 Simulated leak test results . 45
A.10 Qualification for use . 45
A.11 Statistical analysis . 46
Annex B (informative) Acquisition of field data to provide a standard database for testing
software leak detection systems Category B(2) . 51
B.1 General . 51
B.2 File sorting and selection .
...