iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 1852-1:1997

(Main)

Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene (PP) - Part 1: Specifications for pipes, fittings and the system

Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene (PP) - Part 1: Specifications for pipes, fittings and the system

This Part of prEN 1852 specifies the requirements for pipes, fittings and the system of polypropylene (PP) piping systems in the field of non-pressure under- ground drainage and sewerage outside the building structure (application area code "U") and for non-pressure underground drainage and sewerage for both buriedin ground within the building structure (application area code "D") and outside the building structure. This is reflected in the marking of products by "U" and "UD".

Kunststoff-Rohrleitungssysteme für erdverlegte Abwasserkanäle und -leitungen - Polypropylen (PP) - Teil 1: Anforderungen an Rohre, Formstücke und das Rohrleitungssystem

Diese Norm legt für Rohrleitungssysteme aus Polypropylen (PP) Anforderungen an Rohre, Formstücke und das System für Abwasser kanäle und -leitungen fest, diein erdverlegten Schwerkraftenwässerungssystemen -ausserhalb der Gebäude- struktur (Anwendungskennzeichen "U") sowie - innerhalb der Gebäudestruktur (Anwendungskennzeichen "D") und ausserhalb der Gebäudestruktur eingesetzt werden.

Systèmes de canalisations en plastique pour les branchements et les collecteurs enterrés d'assainissement sans pression - Polypropylène (PP) - Partie 1: Spécifications pour les tubes, les raccords et le système

Cett partie du prEn 1852 spécifie les exigences pour les tubes, les raccords et le système de canalisation en polypropylène (PP), dans le domaine des bran- chements et des collecteurs enterrés d'assainissement sans pression à l'exté- rieur de la structure des bâtiments (code de zone d'application "U") et pour les branchements et collecteurs enterrés d'assainissement sans pression ins- tallés aussi bien enterré à l'intérieur de la structure des bâtiments (code de zone d'application "D") qu'à l'extérieur de la structure des bâtiments. Ceci seretrouve dans le marquage "U" et "UD" des produits.

Cevni sistemi iz polimernih materialov za odpadno vodo in kanalizacijo, ki delujejo po težnostnem principu in so položeni v zemljo - Polipropilen (PP) - 1. del: Specifikacije za cevi, fitinge in sistem

General Information

Status
Withdrawn
Publication Date
19-Aug-1997
Withdrawal Date
17-Mar-2009
ICS
23.040.01 - Pipeline components and pipelines in general
23.040.05 - Pipeline and its parts for external sewage systems
91.140.80 - Drainage systems
93.030 - External sewage systems
Technical Committee
CEN/TC 155 - Plastics piping systems and ducting systems
Drafting Committee
CEN/TC 155/WG 11 - System for non-pressure drainage and sewerage - PP (solid wal)
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
18-Mar-2009
Completion Date
18-Mar-2009
Directive
305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
89/106/EEC - Construction products
Ref Project
SIST EN 1852-1:1999 - Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene (PP) - Part 1: Specifications for pipes, fittings and the system

Relations

Replaced By
EN 1852-1:2009 - Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene (PP) - Part 1: Specifications for pipes, fittings and the system
Effective Date
22-Dec-2008
Amended By
EN 1852-1:1997/A1:2002 - Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene (PP) - Part 1: Specifications for pipes, fittings and the system
Effective Date
08-Jun-2022

Buy Standard

EN 1852-1:1999EN 1852-1:1999
PreviousNext
Standard
EN 1852-1:1999
English language
29 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 1852-1:1999
01-julij-1999
Cevni sistemi iz polimernih materialov za odpadno vodo in kanalizacijo, ki delujejo
po težnostnem principu in so položeni v zemljo - Polipropilen (PP) - 1. del:
Specifikacije za cevi, fitinge in sistem
Plastics piping systems for non-pressure underground drainage and sewerage -
Polypropylene (PP) - Part 1: Specifications for pipes, fittings and the system
Kunststoff-Rohrleitungssysteme für erdverlegte Abwasserkanäle und -leitungen -
Polypropylen (PP) - Teil 1: Anforderungen an Rohre, Formstücke und das
Rohrleitungssystem
Systemes de canalisations en plastique pour les branchements et les collecteurs
enterrés d'assainissement sans pression - Polypropylene (PP) - Partie 1: Spécifications
pour les tubes, les raccords et le systeme
Ta slovenski standard je istoveten z: EN 1852-1:1997
ICS:
23.040.01 Deli cevovodov in cevovodi Pipeline components and
na splošno pipelines in general
93.030 Zunanji sistemi za odpadno External sewage systems
vodo
SIST EN 1852-1:1999 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 1852-1:1999

---------------------- Page: 2 ----------------------

SIST EN 1852-1:1999

---------------------- Page: 3 ----------------------

SIST EN 1852-1:1999

---------------------- Page: 4 ----------------------

SIST EN 1852-1:1999

---------------------- Page: 5 ----------------------

SIST EN 1852-1:1999

---------------------- Page: 6 ----------------------

SIST EN 1852-1:1999

---------------------- Page: 7 ----------------------

SIST EN 1852-1:1999

---------------------- Page: 8 ----------------------

SIST EN 1852-1:1999

---------------------- Pa
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
CEN/TS 12666-2:2012(Main)
Plastics piping systems for non-pressure underground drainage and sewerage - Polyethylene (PE) - Part 2: Guidance for the assessment of conformity
SIST-TS CEN/TS 12666-2:2012

This Technical Specification gives guidance for the assessment of conformity of materials, products, joints and assemblies in accordance with the applicable part(s) of EN 12666 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of third-party certification procedures.
NOTE 1   It is recommended that the quality management system conforms to or is no less stringent than the relevant requirements to EN ISO 9001:2008 [1].
NOTE 2   If third-party certification is involved, it is recommended that the certification body is accredited to EN 45011 [2], EN 45012 [3] or EN ISO/IEC 17021 [4], as applicable.
NOTE 3    In order to help the readers, a summary of the test regime is given in Annex A.
In conjunction with EN 12666-1 (see Foreword) this document is applicable to piping systems made of polyethylene (PE):
-   non-pressure underground drainage and sewerage outside the building structure (application area code "U"), reflected in the marking of products by "U", and
-   for non-pressure underground drainage and sewerage for both buried in the ground within the building structure (application area code "D") and outside the building structure (application area code "U"), reflected in the marking of products by "UD".

  • Technical specification
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12666-1:2005+A1:2011(Main + Amendment)
Plastics piping systems for non-pressure underground drainage and sewerage - Polyethylene (PE) - Part 1: Specifications for pipes, fittings and the system
SIST EN 12666-1:2006+A1:2011

This Part of EN 12666 specifies the requirements for pipes, fittings and the system of polyethylene (PE) piping systems intended to be used for
-   non pressure underground drainage and sewerage outside the building structure (application area code "U"), and
-   non pressure underground drainage and sewerage for both buried in the ground within the building structure (application area code "D") and outside the building structure.
This is reflected in the marking of products by "U" and "UD".
It also specifies the test parameters for the test methods referred to in this European Standard.
This European Standard covers a range of nominal sizes, a range of pipe series/stiffness classes and gives recommendations concerning colours.
NOTE 1    It is the responsibility of the purchaser or specifier to make the appropriate selection from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
In conjunction with CEN/TS 12666-2 [1] it is applicable to PE pipes and fittings, their joints and to joints with components of other plastics and non plastics materials intended to be used for buried piping systems for non pressure drainage and sewerage.
This European Standard is applicable to PE pipes with or without an integral socket.
The fittings can be manufactured by injection-moulding or be fabricated from pipes and/or mouldings.
This European Standard is applicable to PE pipes and fittings for the following types of joints:
-   elastomeric ring seal joints;
-   butt fused joints;
-   electrofusion joints;
-   mechanical joints.
NOTE 2   Requirements and limiting values for application area code "D" are given in Tables 3, 6 and Table 12.
NOTE 3    Pipes, fittings and other components conforming to any of the plastics product standards listed in the bibliography may be used with pipes and fittings conforming to this European Standard, provided they conform to the requirements for joint dimensions given in Clause 6 and to the requirements of Table 8 and Table 12.

  • Standard
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TS 12666-2:2012(Main)
Plastics piping systems for non-pressure underground drainage and sewerage - Polyethylene (PE) - Part 2: Guidance for the assessment of conformity
SIST-TS CEN/TS 12666-2:2012

This Technical Specification gives guidance for the assessment of conformity of materials, products, joints and assemblies in accordance with the applicable part(s) of EN 12666 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of third-party certification procedures.
NOTE 1   It is recommended that the quality management system conforms to or is no less stringent than the relevant requirements to EN ISO 9001:2008 [1].
NOTE 2   If third-party certification is involved, it is recommended that the certification body is accredited to EN 45011 [2], EN 45012 [3] or EN ISO/IEC 17021 [4], as applicable.
NOTE 3    In order to help the readers, a summary of the test regime is given in Annex A.
In conjunction with EN 12666-1 (see Foreword) this document is applicable to piping systems made of polyethylene (PE):
-   non-pressure underground drainage and sewerage outside the building structure (application area code "U"), reflected in the marking of products by "U", and
-   for non-pressure underground drainage and sewerage for both buried in the ground within the building structure (application area code "D") and outside the building structure (application area code "U"), reflected in the marking of products by "UD".

  • Technical specification
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12666-1:2005+A1:2011(Main + Amendment)
Plastics piping systems for non-pressure underground drainage and sewerage - Polyethylene (PE) - Part 1: Specifications for pipes, fittings and the system
SIST EN 12666-1:2006+A1:2011

This Part of EN 12666 specifies the requirements for pipes, fittings and the system of polyethylene (PE) piping systems intended to be used for
-   non pressure underground drainage and sewerage outside the building structure (application area code "U"), and
-   non pressure underground drainage and sewerage for both buried in the ground within the building structure (application area code "D") and outside the building structure.
This is reflected in the marking of products by "U" and "UD".
It also specifies the test parameters for the test methods referred to in this European Standard.
This European Standard covers a range of nominal sizes, a range of pipe series/stiffness classes and gives recommendations concerning colours.
NOTE 1    It is the responsibility of the purchaser or specifier to make the appropriate selection from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
In conjunction with CEN/TS 12666-2 [1] it is applicable to PE pipes and fittings, their joints and to joints with components of other plastics and non plastics materials intended to be used for buried piping systems for non pressure drainage and sewerage.
This European Standard is applicable to PE pipes with or without an integral socket.
The fittings can be manufactured by injection-moulding or be fabricated from pipes and/or mouldings.
This European Standard is applicable to PE pipes and fittings for the following types of joints:
-   elastomeric ring seal joints;
-   butt fused joints;
-   electrofusion joints;
-   mechanical joints.
NOTE 2   Requirements and limiting values for application area code "D" are given in Tables 3, 6 and Table 12.
NOTE 3    Pipes, fittings and other components conforming to any of the plastics product standards listed in the bibliography may be used with pipes and fittings conforming to this European Standard, provided they conform to the requirements for joint dimensions given in Clause 6 and to the requirements of Table 8 and Table 12.

  • Standard
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO/ASTM 52924:2023(Main)
Additive manufacturing of polymers - Qualification principles - Classification of part properties (ISO/ASTM 52924:2023)
SIST EN ISO/ASTM 52924:2023

This document establishes the required or the achievable classes of part properties for additive manufactured polymer parts in order to get a common understanding on part quality. It is aimed at providers of manufacturing services for polymer parts who use additive manufacturing machines and at the customers for these services. Designers of parts as well as buyers and providers of manufacturing services can specify, in a traceable manner, the required or the achievable level of part properties with the aid of this document. The classification is based on mechanical, physical and geometrical properties. Further properties can be defined between buyer and provider of manufacturing.
This document is applicable to parts that have been manufactured from a thermoplastic polymer by means of thermal reaction fusion of material typically applied by a powder bed fusion (PBF) or material extrusion (MEX) processes. This document is also applicable to thermoplastic parts made by other processes, provided that due consideration is given to process-specific topics.
The classification of part properties applies to parts in as-built condition, that have been unpacked from the build space, with all support structures removed, but prior to any post-processing operations.
Specific industries (e.g. aerospace and medical) typically specify additional requirements.

  • Draft
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 19111:2020/A2:2023(Amendment)
Geographic information - Referencing by coordinates - Amendment 2 (ISO 19111:2019/Amd 2:2023)
SIST EN ISO 19111:2020/oprA2:2023
  • Draft
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 3581:2023(Main)
Welding consumables - Covered electrodes for manual metal arc welding of stainless and heat-resisting steels - Classification (ISO 3581:2023)
SIST EN ISO 3581:2023

This document specifies requirements for classification of covered electrodes, based on the all-weld metal chemical composition, the type of electrode covering and other electrode properties, and the all-weld metal mechanical properties, in the as-welded or heat-treated conditions, for manual metal arc welding of stainless and heat-resisting steels.
This document is a combined standard providing for classification utilizing a system based upon classification according to nominal composition or utilizing a system based upon classification according to alloy type.
a)       Paragraphs and tables which carry the label “classification according to nominal composition-A” or “ISO 3581-A” are applicable only to products classified to that system.
b)       Paragraphs and tables which carry the label “classification according to alloy type-B” or “ISO 3581-B” are applicable only to products classified to that system.
c)        Paragraphs and tables which carry neither label are applicable to products classified according to either or both systems.
Annex B gives information on considerations on weld metal ferrite content.

  • Draft
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 11363-1:2018/A1:2023(Amendment)
Gas cylinders - 17E and 25E taper threads for connection of valves to gas cylinders - Part 1: Specifications - Amendment 1 (ISO 11363-1:2018/Amd 1:2023)
SIST EN ISO 11363-1:2018/A1:2023
  • Draft
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 11267:2023(Main)
Soil quality - Inhibition of reproduction of Collembola (Folsomia candida) by soil contaminants (ISO 11267:2023)
SIST EN ISO 11267:2023

This document specifies one of the methods for evaluating the habitat function of soils and determining effects of soil contaminants and substances on the reproduction of Folsomia candida Willem by dermal and alimentary uptake. This document also provides information on how to use this method for testing substances under temperate conditions.
The chronic test described is applicable to soils and soil materials of unknown quality, e.g. from contaminated sites, amended soils, soils after remediation, industrial, agricultural or other sites of concern and waste materials.
The method is not applicable to volatile substances, i.e. substances for which H (Henry's constant) or the air/water partition coefficient is greater than 1, or for which the vapour pressure exceeds 300 Pa at 25 °C.

  • Draft
    41 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 18743:2015/A1:2023(Amendment)
Microbiology of the food chain - Detection of Trichinella larvae in meat by artificial digestion method - Amendment 1: Method validation studies and performance characteristics (ISO 18743:2015/Amd 1:2023)
SIST EN ISO 18743:2015/A1:2023
  • Draft
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day