iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 13411-6:2004

(Main)

Terminations for steel wire ropes - Safety - Part 6: Asymmetric wedge socket

Terminations for steel wire ropes - Safety - Part 6: Asymmetric wedge socket

This European Standard specifies the minimum requirements, for asymmetrical wedge socket terminations for stranded steel wire ropes.
Steel asymmetric wedge sockets conforming to this standard are suitable for use at environment temperature.
Cast iron asymmetric wedge sockets conforming to this standard are suitable for use at environment temperature.
Examples of the construction and sizes of two separate designs of asymmetric wedge sockets are given in informative annexes A and B.
The informative annex C gives recommendations for safe use and inspection.
This European Sstandard deals with all significant hazards, hazardous situations and events relevant to asymmetric wedge sockets for terminations for steel wire ropes, when used as intended and under conditions of misuse which are reasonable foreseeable by the manufacturer.
This standard applies to terminations of steel wire ropes with asymmetrical wedge sockets which are manufactured after the date of its publication.
This standard does not cover rope fatigue.

Endverbindungen für Drahtseile aus Stahldraht - Sicherheit - Teil 6: Asymmetrische Seilschlösser

Diese Europäische Norm legt die Mindestanforderungen an asymmetrische Seilschlösser für Endverbindungen an Litzenseilen aus Stahldraht fest.
Beispiele für Konstruktion und Nenngrößen für zwei verschiedene Ausführungen von asymmetrischen Seilschlössern sind in den informativen Anhängen A und B angegeben.
Anhang C gibt Empfehlungen für den sicheren Gebrauch und die Prüfung.
Diese Europäische Norm behandelt alle für asymmetrische Seilschlösser für Seilendverbindungen bedeutsamen Gefährdungen, gefährlichen Situationen und Ereignisse, wenn diese wie vorgesehen verwendet werden und wenn sie unter falschen Bedingungen eingesetzt werden, soweit dies vom Hersteller vernünftigerweise vorhersehbar ist.
Diese Norm gilt für Seilendverbindungen mit asymmetrischen Seilschlössern, die nach dem Datum der Veröffentlichung hergestellt wurden.
Die Dauerfestigkeit von Seilen ist nicht Gegenstand dieser Norm.

Terminaisons pour câbles en acier - Sécurité - Partie 6: Boîte à coin asymétrique

La présente Norme européenne spécifie les prescriptions minimales de sécurité des terminaisons pour boîte à coin asymétrique destinées aux câbles en acier toronnés.
Des exemples de construction et de dimensions de deux modèles distincts de boîtes à coin asymétriques sont donnés dans les Annexes informatives A et B.
L'Annexe informative C donne des recommandations relatives à la sécurité d'emploi et au contrôle.
La présente Norme européenne traite de tous les phénomènes, situations et événements dangereux significatifs relatifs aux boîtes à coin asymétriques pour terminaisons de câbles en acier utilisables dans les conditions prévues ainsi que dans des conditions de mauvais usage raisonnablement prévisibles par le fabricant.
La présente norme est applicable aux terminaisons de câbles en acier à boîte à coin asymétrique fabriquées après sa date de publication.
La présente norme ne traite pas de la fatigue des câbles.

Zaključki jeklenih žičnih vrvi - Varnost - 6. del: Asimetrični zagozdni spoji

General Information

Status
Withdrawn
Publication Date
29-Jun-2004
Withdrawal Date
21-Oct-2008
ICS
53.020.30 - Accessories for lifting equipment
77.140.99 - Other iron and steel products
Technical Committee
CEN/TC 168 - Chains, ropes, webbing, slings and accessories - safaty
Drafting Committee
CEN/TC 168/WG 2 - Steel wire ropes, their terminations and wire rope slings
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
22-Oct-2008
Completion Date
22-Oct-2008
Directive
98/37/EC - Machinery
Mandate
M/BC/CEN/91/1 - Standardization request to CEN/CENELEC concerning machines presenting hazards due to mobility or load lifting
Ref Project
SIST EN 13411-6:2004 - Terminations for steel wire ropes - Safety - Part 6: Asymmetric wedge socket

Relations

Merged Into
EN 13411-6:2004+A1:2008 - Terminations for steel wire ropes - Safety - Part 6: Asymmetric wedge socket
Effective Date
19-Jan-2023

Buy Standard

EN 13411-6:2004EN 13411-6:2004
PreviousNext
Standard
EN 13411-6:2004
English language
23 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 13411-6:2004
01-november-2004
=DNOMXþNLMHNOHQLKåLþQLKYUYL9DUQRVWGHO$VLPHWULþQL]DJR]GQLVSRML
Terminations for steel wire ropes - Safety - Part 6: Asymmetric wedge socket
Endverbindungen für Drahtseile aus Stahldraht - Sicherheit - Teil 6: Asymmetrische
Seilschlösser
Terminaisons pour câbles en acier - Sécurité - Partie 6: Boîte a coin asymétrique
Ta slovenski standard je istoveten z: EN 13411-6:2004
ICS:
53.020.30 Pribor za dvigalno opremo Accessories for lifting
equipment
77.140.99 Drugi železni in jekleni izdelki Other iron and steel products
SIST EN 13411-6:2004 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 13411-6:2004

---------------------- Page: 2 ----------------------

SIST EN 13411-6:2004
EUROPEAN STANDARD
EN 13411-6
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2004
ICS 53.020.30; 77.140.99
English version
Terminations for steel wire ropes - Safety - Part 6: Asymmetric
wedge socket
Terminaisons pour câbles en acier - Sécurité - Partie 6: Endverbindungen für Drahtseile aus Stahldraht - Sicherheit
Boîte à coin asymétrique - Teil 6: Asymmetrische Seilschlösser
This European Standard was approved by CEN on 24 March 2004.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2004 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13411-6:2004: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 13411-6:2004
EN 13411-6:2004 (E)
Contents             page
Foreword.3
Introduction .4
1 Scope.5
2 Normative references.5
3 Terms and definitions .5
4 List of significant hazards .6
5 Safety requirements and/or measures .7
6 Verification of safety requirements.9
7 Information for use .12
Annex A (informative) Asymmetric wedge socket with cast socket body – Design 1 .13
Annex B (informative) Asymmetric wedge socket with cast socket body – Design 2 .16
Annex C (informative) Recommendations for safe use and inspection .19
Annex ZA (informative) Relationship of this document with EC Directives.22
Bibliography .23


2

---------------------- Page: 4 ----------------------

SIST EN 13411-6:2004
EN 13411-6:2004 (E)
Foreword
This document
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 13411-8:2011(Main)
Terminations for steel wire ropes - Safety - Part 8: Swage terminals and swaging
SIST EN 13411-8:2012

This European Standard specifies the minimum requirements for swage terminals and the securing of such terminals by a swaging process to carbon steel rope conforming to EN 12385-4 and EN 12385-5, spiral strand rope conforming to EN 12385-10 and stainless steel stranded rope.
This European Standard is not applicable to spiral rope incorporating full lock wires - see EN 12385-10 -, nor ropes with coverings and /or fillings (see 3.6.3 of EN 12385-2:2002+A1:2008).
This European Standard is applicable to swaged terminations that have a terminal efficiency factor, KT, of at least 0,9 and are used as part of a wire rope accessory such as a sling, or wire rope assembly that performs a raising, lowering, hauling or supporting function on lifting machinery.
This European Standard is applicable to terminals of the following types that are made of carbon or stainless steel:
-   open swage socket;
-   closed swage socket;
-   swage terminal with thread;
-   swage terminal end stop.
This European Standard deals with all significant hazards, hazardous situations and events relevant to swaged terminations, when used as intended and under conditions of misuse which are reasonably foreseeable (see Clause 4).
This European Standard applies to swaged terminations which are manufactured after the date of its publication.
This European Standard is not applicable to swaged terminations used for anchoring ropes to winch drums.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13411-8:2011(Main)
Terminations for steel wire ropes - Safety - Part 8: Swage terminals and swaging
SIST EN 13411-8:2012

This European Standard specifies the minimum requirements for swage terminals and the securing of such terminals by a swaging process to carbon steel rope conforming to EN 12385-4 and EN 12385-5, spiral strand rope conforming to EN 12385-10 and stainless steel stranded rope.
This European Standard is not applicable to spiral rope incorporating full lock wires - see EN 12385-10 -, nor ropes with coverings and /or fillings (see 3.6.3 of EN 12385-2:2002+A1:2008).
This European Standard is applicable to swaged terminations that have a terminal efficiency factor, KT, of at least 0,9 and are used as part of a wire rope accessory such as a sling, or wire rope assembly that performs a raising, lowering, hauling or supporting function on lifting machinery.
This European Standard is applicable to terminals of the following types that are made of carbon or stainless steel:
-   open swage socket;
-   closed swage socket;
-   swage terminal with thread;
-   swage terminal end stop.
This European Standard deals with all significant hazards, hazardous situations and events relevant to swaged terminations, when used as intended and under conditions of misuse which are reasonably foreseeable (see Clause 4).
This European Standard applies to swaged terminations which are manufactured after the date of its publication.
This European Standard is not applicable to swaged terminations used for anchoring ropes to winch drums.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 22435:2024(Main)
Gas cylinders - Cylinder valves with integrated pressure regulators - Specification and type testing (ISO 22435:2024)
kSIST FprEN ISO 22435:2024

This document specifies design, type test methods, marking and instruction requirements for cylinder valves with integrated pressure regulators (VIPRs) intended to be fitted to gas cylinders, pressure drums or tubes or used as a main valve for bundles of cylinders that convey compressed, liquefied or dissolved gases.
These are requirements for VIPRs that are in addition to those given in the relevant closure standard, for example, in ISO 10297 for cylinder valves, in ISO 17871 for quick-release cylinder valves, in ISO 17879 for self-closing cylinder valves or in ISO 23826 for ball valves. For ISO 17871, these requirements are only applicable to quick-release cylinder valves types B, C, D and E.
NOTE 1        If the pressure regulating system of a VIPR is acting as the primary valve operating mechanism, it is covered by the relevant closure standard, e.g. ISO 10297, ISO 17871, ISO 17879 and ISO 23826. This also includes designs where closure of the primary valve operating mechanism of a VIPR is obtained by closing the seat of the pressure regulating system.
NOTE 2        If the primary valve operating mechanism of a VIPR is located at the low-pressure side of the pressure regulating system, it is covered by the relevant closure standard, e.g. ISO 10297, ISO 17871, ISO 17879 and ISO 23826.
NOTE 3        The term “pressure receptacle” is used within this document to cover instances where no differentiation is necessary between gas cylinders, bundles of cylinders, pressure drums and tubes.
This document does not apply to VIPRs for
a)       medical applications (see ISO 10524-3);
b)       liquefied petroleum gas (LPG);
c)        cryogenic applications.
NOTE 4        Additional requirements for a VIPR with a residual pressure device (RPD) are specified in ISO 15996.
NOTE 5        Additional requirements for pressure relief valves can exist in international/regional regulations/ standards.

  • Draft
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17015-1:2024(Main)
Electronic Public Procurement - Catalogue - Part 1: Choreographies
kSIST FprEN 17015-1:2024

The purpose of this deliverable is to specify and describe choreographies for exchanging an electronic product catalogue (“catalogues”) as part of the business processes in the pre-award and post-award area, so that catalogues can serve as a basis for placing orders as well as evaluating tenders. The key aspects covered by this choreography specification are:
-   processes for submitting catalogues from the selling to the buying side;
-   processes for submitting catalogue-related data as part of a tendering process;
-   processes integrating sell-side procurement systems.
This document does not apply to the transactions used in the specified choreographies. These transactions are specified in EN 17015 2. The relationship between the choreographies and the transaction is described in Clause 8.
The identifier of this choreographies document is EN 17015 1:2024.
How to claim compliance to this choreography is specified in 6.2.3.

  • Draft
    38 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO/ASTM 52927:2024(Main)
Additive manufacturing - General principles - Main characteristics and corresponding test methods (ISO/ASTM 52927:2024)
kSIST FprEN ISO/ASTM 52927:2024

This document specifies the principal requirements applied to the testing of parts produced by additive manufacturing processes.
This document
—     identifies quality characteristics for feedstock and parts and the corresponding test procedures,
—     provides the specific procedures to build specimens using additive manufacturing process, and
—     recommends the scope and content of test and supply agreements.
This document is aimed at machine manufacturers, feedstock suppliers, AM system users, part providers, and customers to facilitate the communication on main quality characteristics. It applies wherever additive manufacturing processes are used.
NOTE            It is the intent to include, in future versions of this document, other characteristics such as thermal properties, electrical requirements and physical and physico-chemical properties based upon material types.

  • Draft
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 8362-2:2024(Main)
Injection containers and accessories - Part 2: Closures for injection vials (ISO 8362-2:2024)
SIST EN ISO 8362-2:2024

This document specifies the shape, dimensions, material, performance requirements and labelling of closures for injection vials covered by ISO 8362-1 and ISO 8362-4.
The dimensional requirements are not applicable to barrier-coated closures.
Closures specified in this document are intended for single use only.
NOTE            The potency, purity, stability and safety of a medicinal product during its manufacture and storage can strongly be affected by the nature and performance of the primary packaging.

  • Draft
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 16739-1:2024(Main)
Industry Foundation Classes (IFC) for data sharing in the construction and facility management industries - Part 1: Data schema (ISO 16739-1:2024)
kSIST FprEN ISO 16739-1:2024

This document represents an open international standard for information used in Building Information Modeling (BIM) that is exchanged and shared among software applications used by the various participants in the construction or facility management industry sector. This document includes definitions that cover information required for buildings and infrastructure works over their life cycle. This edition of the document added coverage of information required for infrastructure facilities including bridges, roads, railways, waterways and port facilities.
This document comprises the publication of a data schema, its documentation, the property and quantity set definitions and the mechanism of an exchange file format structure.
Definitions from this document are used to support different recognized work flows in the construction and facility management industry sector, representing information deliveries. Such information deliveries can be described according to ISO 29481.
Different implementation levels of this document can be defined to better support multiple information deliveries, they are referred to as a Model View Definition (MVD). Each MVD identifies which subset of the definitions of this document imposes requirements for implementation in software applications. Conforming software applications need to identify the model view definition they conform to when applying for software certification.
The following are within the scope of this edition of this document:
BIM exchange format definitions that are required during the life cycle phases of buildings and infrastructure:
demonstrating the need;
conception of need;
outline feasibility;
substantive feasibility study and outline financial authority;
outline conceptual design;
full conceptual design;
coordinated design;
procurement and full financial authority;
production information;
construction;
operation and maintenance.
BIM exchange format definitions that are required by the various disciplines involved within the life cycle phases:
architecture and civil engineering design;
service and utilities engineering;
structural engineering;
procurement;
construction planning;
facility and utility management;
project management;
client requirement management;
industry authorities for permits and approval.
BIM exchange format definitions including:
project structure;
physical components;
spatial components;
analysis items;
processes;
resources;
controls;
actors;
context definition.

  • Draft
    406 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 2620:2024(Main)
Analysis of natural gas - Biomethane - Determination of VOCs by thermal desorption gas chromatography with flame ionization and/or mass spectrometry detectors (ISO 2620:2024)
kSIST FprEN ISO 2620:2024

This document describes a method for sampling and analysis of volatile organic compounds (VOCs), including siloxanes, terpenes, organic sulfur compounds, in natural gas and biomethane matrices, using thermal desorption gas chromatography with flame ionization and/or mass spectrometry detectors (TD-GC-FID/MS).

  • Draft
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 4126-10:2024(Main)
Safety devices for protection against excessive pressure - Part 10: Sizing of safety valves and bursting discs for gas/liquid two-phase flow (ISO 4126-10:2024)
kSIST FprEN ISO 4126-10:2023

This document specifies the sizing of safety valves and bursting discs for gas/liquid two-phase flow in pressurized systems such as reactors, storage tanks, columns, heat exchangers, piping systems or transportation tanks/containers, see Figure 2. The possible fluid states at the safety device inlet that can result in two-phase flow are given in Table 1.
NOTE          The pressures used in this document are absolute pressures, not gauge pressures.

  • Draft
    84 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 17294-1:2024(Main)
Water quality - Application of inductively coupled plasma mass spectrometry (ICP-MS) - Part 1: General requirements (ISO 17294-1:2024)
kSIST FprEN ISO 17294-1:2023

This document specifies the principles of inductively coupled plasma mass spectrometry (ICP-MS) and provides general requirements for the use of this technique to determine elements in water, digests of sludges and sediments (e.g. digests of water as described in ISO 15587-1 or ISO 15587-2). Generally, the measurement is carried out in water, but gases, vapours or fine particulate matter can be introduced too. This document applies to the use of ICP-MS for aqueous solution analysis.
The ultimate determination of the elements is described in a separate International Standard for each series of elements and matrix. The individual clauses of this document refer the user to these guidelines for the basic principles of the method and the configuration of the instrument.

  • Draft
    43 pages
    English language
    sale 10% off
    e-Library read for
    1 day