EN ISO 15546:2007
(Main)Petroleum and natural gas industries - Aluminium alloy drill pipe (ISO 15546:2007)
Petroleum and natural gas industries - Aluminium alloy drill pipe (ISO 15546:2007)
ISO 15546:2007 specifies the technical delivery condition, manufacturing process, material requirements, configuration and dimensions, and verification and inspection procedures for aluminium alloy drill pipes with or without attached steel tool joints for use in drilling and production operations in the petroleum and natural gas industries.
Erdöl- und Erdgasindustrie - Bohrrohre aus Aluminiumlegierungen (ISO 15546:2007)
Industries du pétrole et du gaz naturel - Tige de forage en alliage d'aluminium (ISO 15546:2007)
L'ISO 15546:2007 spécifie les conditions techniques de livraison, le procédé de fabrication, les exigences de matériau, la configuration et les dimensions, les procédures de vérification et d'inspection pour les tiges de forage en alliage d'aluminium, avec ou sans raccords vissés en acier, convenant à l'emploi dans les opérations de forage et de production dans les industries du pétrole et du gaz naturel.
Industrija za predelavo nafte in zemeljskega plina - Vrtalne cevi iz aluminijevih zlitin (ISO 15546:2007)
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Industrija za predelavo nafte in zemeljskega plina - Vrtalne cevi iz aluminijevih zlitin (ISO 15546:2007)Erdöl- und Erdgasindustrie - Bohrrohre aus Aluminiumlegierungen (ISO 15546:2007)Industries du pétrole et du gaz naturel - Tige de forage en alliage d'aluminium (ISO 15546:2007)Petroleum and natural gas industries - Aluminium alloy drill pipe (ISO 15546:2007)77.150.10Aluminijski izdelkiAluminium products75.180.10Oprema za raziskovanje in odkopavanjeExploratory and extraction equipmentICS:Ta slovenski standard je istoveten z:EN ISO 15546:2007SIST EN ISO 15546:2007en,fr01-junij-2007SIST EN ISO 15546:2007SLOVENSKI
STANDARDSIST EN ISO 15546:20041DGRPHãþD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN ISO 15546May 2007ICS 75.180.10; 77.150.10Supersedes EN ISO 15546:2002
English VersionPetroleum and natural gas industries - Aluminium alloy drill pipe(ISO 15546:2007)Industries du pétrole et du gaz naturel - Tige de forage enalliage d'aluminium (ISO 15546:2007)Erdöl- und Erdgasindustrie - Bohrrohre ausAluminiumlegierungen (ISO 15546:2007)This European Standard was approved by CEN on 14 May 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2007 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN ISO 15546:2007: ESIST EN ISO 15546:2007
Foreword
This document (EN ISO 15546:2007) has been prepared by Technical Committee ISO/TC 67 "Materials, equipment and offshore structures for petroleum and natural gas industries" in collaboration with Technical Committee CEN/TC 12 "Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries", the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November 2007, and conflicting national standards shall be withdrawn at the latest by November 2007.
This document supersedes EN ISO 15546:2002.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Endorsement notice
The text of ISO 15546:2007 has been approved by CEN as EN ISO 15546:2007 without any modifications.
Reference numberISO 15546:2007(E)© ISO 2007
INTERNATIONAL STANDARD ISO15546Second edition2007-05-15Petroleum and natural gas industries — Aluminium alloy drill pipe Industries du pétrole et du gaz naturel — Tige de forage en alliage d'aluminium
ISO 15546:2007(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
©
ISO 2007 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel.
+ 41 22 749 01 11 Fax
+ 41 22 749 09 47 E-mail
copyright@iso.org Web
www.iso.org Published in Switzerland
ii © ISO 2007 – All rights reserved
ISO 15546:2007(E) © ISO 2007 – All rights reserved iiiContents Page Foreword.iv Introduction.v 1 Scope.1 2 Normative references.1 3 Terms, definitions and symbols.2 3.1 Terms and definitions.2 3.2 Symbols.3 4 Information to be supplied by purchaser.4 5 Process of manufacture and delivery condition.5 5.1 General.5 5.2 Heat treatment.5 5.3 Traceability.5 5.4 Delivery condition.5 6 Material requirements.5 6.1 Material groups.5 6.2 Metallographic examination.6 6.3 Chemical composition.6 6.4 Steel tool joints.6 7 Configuration and dimensions of pipes.7 7.1 Configuration.7 7.2 Length.7 7.3 Dimensions of pipes and tool joints.9 7.4 Design mass.15 7.5 Upset run-out.19 7.6 Straightness.19 7.7 Ovality and eccentricity of pipes.19 7.8 Drift requirements.20 7.9 Internal coating.20 7.10 Drill pipe-tool joint assembly.20 8 Test methods.21 9 Measuring methods.22 10 Inspection.22 11 Marking.23 12 Packaging, transport and storage.23 13 Documents.24 13.1 Certification.24 13.2 Retention of records.24 14 Delivery conditions.24 Annex A (normative)
Purchaser inspection.25 Annex B (normative)
Supplementary requirement — Full scale fatigue design verification test.26 Annex C (normative)
Corrosion test.28 Bibliography.29
ISO 15546:2007(E) iv © ISO 2007 – All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 15546 was prepared by Technical Committee ISO/TC 67, Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries. This second edition cancels and replaces the first edition (ISO 15546:2002), of which it constitutes a minor revision. SIST EN ISO 15546:2007
ISO 15546:2007(E) © ISO 2007 – All rights reserved vIntroduction Users of this International Standard need to be aware that further or differing requirements could be needed for individual applications. This International Standard is not intended to inhibit a manufacturer from offering, or the purchaser from accepting, alternative equipment or engineering solutions for the individual application — particularly applicable where there is innovative or developing technology. Where an alternative is offered, the manufacturer will need to identify any variations from this International Standard and provide details. This International Standard includes requirements of various nature. These are identified by the use of certain verbal forms: ⎯ “shall” is used to indicate that a provision is mandatory; ⎯ “should” is used to indicate that a provision is not mandatory, but recommended as good practice; ⎯ “may” is used to indicate that a provision is optional.
INTERNATIONAL STANDARD ISO 15546:2007(E) © ISO 2007 – All rights reserved 1Petroleum and natural gas industries — Aluminium alloy drill pipe 1 Scope This International Standard specifies the technical delivery condition, manufacturing process, material requirements, configuration and dimensions, and verification and inspection proced
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.