EN ISO 11299-3:2013

Plastics piping systems for renovation of underground gas supply networks - Part 3: Lining with close-fit pipes (ISO 11299-3:2011)

ISO 11299-3:2011, in conjunction with ISO 11299-1, specifies requirements and test methods for close-fit lining systems intended to be used for the renovation of gas supply networks.
ISO 11299-3:2011 is applicable to polyethylene (PE) pipes for both independent and interactive pressure pipe liners as well as associated fittings and joints for the construction of the lining system.

Kunststoff-Rohrleitungssysteme für die Renovierung von erdverlegten Gasversorgungsnetzwerken - Teil 3: Close-Fit-Lining (ISO 11299-3:2011)

Dieser Teil der ISO 11299 legt in Verbindung mit ISO 11299-1 die Anforderungen und Prüfverfahren für Close-Fit-Lining-Systeme fest, die bei der Renovierung von Gasversorgungsnetzwerken verwendet werden.
Er gilt für Rohre aus Polyethylen (PE) sowohl für unabhängige als auch für interaktive Druck-Liner-Rohre und die dazugehörigen Formstücke und Verbindungen für den Bau des Lining-Systems.

Systèmes de canalisations en plastique pour la rénovation des réseaux de gaz enterrés - Partie 3: Tubage par tuyau continu sans espace annulaire (ISO 11299-3:2011)

L'ISO 11299-3:2011, conjointement à l'ISO 11299-1, spécifie les exigences et les méthodes d'essai pour les systèmes de tubages par tuyau continu sans espace annulaire utilisés pour la rénovation des réseaux de gaz.
L'ISO 11299-3:2011 s'applique aux tuyaux en polyéthylène (PE) à la fois pour les tubages autostructurants et les tubages nécessitant le maintien de l'enveloppe, ainsi qu'aux raccords associés et aux assemblages pour la construction du système de rénovation.

Cevni sistemi iz polimernih materialov za obnovo podzemnih omrežij za oskrbo s plinom - 3. del: Oblaganje s tesno prilagodljivimi cevmi (ISO 11299-3:2011)

Ta del standarda ISO 11299 v povezavi s standardom ISO 11299-1 določa zahteve in preskusne metode za tesno prilagodljive sisteme oblaganja, ki se uporabljajo za obnovo podzemnih omrežij za oskrbo s plinom. Uporablja se za cevi iz polietilena, ki so izdelane za neodvisne ter interaktivne obloge cevi s tlakom in povezane fitinge ter spoje za izdelavo sistema oblog.

General Information

• Status: Withdrawn
• Publication Date: 19-Feb-2013
• Withdrawal Date: 04-Dec-2018
• ICS: 23.040.20 - Plastics pipes
• ICS: 23.040.45 - Plastics fittings
• ICS: 75.200 - Petroleum products and natural gas handling equipment
• Technical Committee: CEN/TC 155 - Plastics piping systems and ducting systems
• Drafting Committee: CEN/TC 155/WG 17 - Plastic components for the use of renovation of piping systems
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Completion Date: 05-Dec-2018
• Ref Project: SIST EN ISO 11299-3:2013 - Plastics piping systems for renovation of underground gas supply networks - Part 3: Lining with close-fit pipes (ISO 11299-3:2011)

Relations

• Replaces: EN 14408-3:2004 - Plastics piping systems for renovation of underground gas supply networks - Part 3: Lining with close-fit pipes
• Effective Date: 02-May-2012
• Replaced By: EN ISO 11299-3:2018 - Plastics piping systems for renovation of underground gas supply networks - Part 3: Lining with close-fit pipes (ISO 11299-3:2018)
• Effective Date: 11-Dec-2018

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 11299-3:2013
01-april-2013
1DGRPHãþD
SIST EN 14408-3:2005
Cevni sistemi iz polimernih materialov za obnovo podzemnih omrežij za oskrbo s
plinom - 3. del: Oblaganje s tesno prilagodljivimi cevmi (ISO 11299-3:2011)
Plastics piping systems for renovation of underground gas supply networks - Part 3:
Lining with close-fit pipes (ISO 11299-3:2011)
Kunststoff-Rohrleitungssysteme für die Renovierung von erdverlegten
Gasversorgungsnetzwerken - Teil 3: Close-Fit-Lining (ISO 11299-3:2011)
Systèmes de canalisations en plastique pour la rénovation des réseaux de gaz enterrés -
Partie 3: Tubage par tuyau continu sans espace annulaire (ISO 11299-3:2011)
Ta slovenski standard je istoveten z: EN ISO 11299-3:2013
ICS:
83.140.30 Cevi, fitingi in ventili iz Plastics pipes, fittings and
polimernih materialov valves
91.140.40 Sistemi za oskrbo s plinom Gas supply systems
SIST EN ISO 11299-3:2013 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 11299-3:2013

---------------------- Page: 2 ----------------------

SIST EN ISO 11299-3:2013


EUROPEAN STANDARD
EN ISO 11299-3

NORME EUROPÉENNE

EUROPÄISCHE NORM
February 2013
ICS 23.040.20; 23.040.45; 75.200 Supersedes EN 14408-3:2004
English Version
Plastics piping systems for renovation of underground gas
supply networks - Part 3: Lining with close-fit pipes (ISO 11299-
3:2011)
Systèmes de canalisations en plastique pour la rénovation Kunststoff-Rohrleitungssysteme für die Renovierung von
des réseaux de gaz enterrés - Partie 3: Tubage par tuyau erdverlegten Gasversorgungsnetzwerken - Teil 3: Close-Fit-
continu sans espace annulaire (ISO 11299-3:2011) Lining (ISO 11299-3:2011)
This European Standard was approved by CEN on 5 February 2013.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2013 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11299-3:2013: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 11299-3:2013
EN ISO 11299-3:2013 (E)
Contents Page
Foreword .3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 11299-3:2013
EN ISO 11299-3:2013 (E)
Foreword
The text of ISO 11299-3:2011 has been prepared by Technical Committee ISO/TC 138 “Plastics pipes, fittings
and valves for the transport of fluids” of the International Organization for Standardization (ISO) and has been
taken over as EN ISO 11299-3:2013 by Technical Committee CEN/TC 155 “Plastics piping systems and
ducting systems” the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by August 2013, and conflicting national standards shall be withdrawn at
the latest by August 2013.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 14408-3:2004.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands
...