EN ISO 3861:2008
(Main)Rubber hoses for sand and grit blasting - Specification (ISO 3861:2005)
Rubber hoses for sand and grit blasting - Specification (ISO 3861:2005)
ISO 3861:2005 specifies the requirements for rubber hoses for wet and dry sand and grit blasting, suitable for use up to a maximum working pressure of 6,3 bar and over an operating temperature range of -25 °C to +70 °C.
Gummischläuche zum Sandstrahlen - Anforderungen (ISO 3861:2005)
Diese Internationale Norm legt die Anforderungen an Gummischläuche zum Strahlen mit trockenem und nassem Sand und Kies fest, die für die Verwendung bis zu einem maximalen Betriebsdruck von 6,3 bar und einem Betriebs¬temperatur¬bereich von 25 °C bis 70 °C geeignet sind.
Tuyaux en caoutchouc pour sablage et grenaillage - Spécifications (ISO 3861:2005)
L'ISO 3861:2005 spécifie les exigences pour les tuyaux en caoutchouc destinés au sablage, sec et humide, et au grenaillage, pouvant être utilisés jusqu'à une pression maximale de service de 6,3 bar et à des températures de service comprises entre -25 °C et +70 °C.
Gumene cevi za peskanje - Specifikacija (ISO 3861:2005)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 3861:2009
01-maj-2009
1DGRPHãþD
SIST EN ISO 3861:2000
Gumene cevi za peskanje - Specifikacija (ISO 3861:2005)
Rubber hoses for sand and grit blasting - Specification (ISO 3861:2005)
Tuyaux en caoutchouc pour sablage et grenaillage - Spécifications (ISO 3861:2005)
Ta slovenski standard je istoveten z: EN ISO 3861:2008
ICS:
83.140.40 Gumene cevi Hoses
SIST EN ISO 3861:2009 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 3861:2009
---------------------- Page: 2 ----------------------
SIST EN ISO 3861:2009
EUROPEAN STANDARD
EN ISO 3861
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2008
ICS 25.220.10; 83.140.40 Supersedes EN ISO 3861:1997
English Version
Rubber hoses for sand and grit blasting - Specification (ISO
3861:2005)
Tuyaux en caoutchouc pour sablage et grenaillage -
Spécifications (ISO 3861:2005)
This European Standard was approved by CEN on 29 October 2008.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 3861:2008: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 3861:2009
EN ISO 3861:2008 (E)
Contents Page
Foreword.3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 3861:2009
EN ISO 3861:2008 (E)
Foreword
The text of ISO 3861:2005 has been prepared by Technical Committee ISO/TC 45 “Rubber and rubber
products” of the International Organization for Standardization (ISO) and has been taken over as EN ISO
3861:2008 by Technical Committee CEN/TC 218 “Rubber and plastics hoses and hose assemblies” the
secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by May 2009, and conflicting national standards shall be withdrawn at the
latest by May 2009.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 3861:1997.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 3861:2005 has been approved by CEN as a EN ISO 3861:2008 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 3861:2009
---------------------- Page: 6 ----------------------
SIST EN ISO 3861:2009
INTERNATIONAL ISO
STANDARD 3861
Third edition
2005-02-15
Rubber hoses for sand and grit
blasting — Specification
Tuyaux en caoutchouc pour sablage et grenaillage — Spécifications
Reference number
ISO 3861:2005(E)
©
ISO 2005
---------------------- Page: 7 ----------------------
SIST EN ISO 3861:2009
ISO 3861:2005(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, pa
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.