EN IEC 62196-2:2022
(Main)Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 2: Dimensional compatibility requirements for AC pin and contact-tube accessories
Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 2: Dimensional compatibility requirements for AC pin and contact-tube accessories
This part of IEC 62196 applies to EV plugs, EV socket-outlets, vehicle connectors and vehicle inlets with pins and contact-tubes of standardized configurations, herein referred to as accessories. These accessories have a nominal rated operating voltage not exceeding 480 V AC, 50 Hz to 60 Hz, and a rated current not exceeding 63 A three phase or 70 A single phase, for use in conductive charging of electric vehicles. This document covers the basic interface accessories for vehicle supply as specified in IEC 62196-1. NOTE 1 The term "Electric road vehicles (EV)" comprises all road vehicles, including plug-in hybrid road vehicles (PHEV) that derive all or part of their energy from the rechargeable energy storage systems (RESS). These accessories are intended to be used for circuits specified in IEC 61851-1:2017, which operate at different voltages and frequencies, and which can include extra-low voltage (ELV) and communication signals. The use of these accessories for bidirectional power transfer is under consideration. This document applies to accessories to be used in an ambient temperature between -30 °C and +40 °C. NOTE 2 In the following country, other requirements regarding the lower temperature may apply: NO. NOTE 3 In the following country, −35 °C applies: SE. These accessories are intended to be connected only to cables with copper or copper-alloy conductors. Vehicle inlets and vehicle connectors described in this document are intended to be used for charging in modes 1, 2 and 3, cases B and C. The EV socket-outlets and EV plugs covered by this document are intended to be used for charging mode 3 only, case A and B. The modes and permissible connections are specified in IEC 61851-1:2017.
Stecker, Steckdosen, Fahrzeugkupplungen und Fahrzeugstecker - Konduktives Laden von Elektrofahrzeugen - Teil 2: Maßliche Kompatibilitätsanforderungen an Wechselspannungssteckvorrichtungen mit Stiften und Buchsen
Fiches, socles de prise de courant, prises mobiles de véhicule et socles de connecteurs de véhicule - Charge conductive des véhicules électriques - Partie 2: Exigences dimensionnelles de compatibilité pour les appareils à broches et alvéoles pour courant alternatif
L’IEC 62196-2:2022 s’applique aux fiches VE, aux socles de prise de courant VE, aux prises mobiles et socles de connecteurs de véhicule, à broches et alvéoles, de configurations normalisées, ci-après dénommés appareils. Ces appareils ont une tension assignée d’emploi ne dépassant pas 480 V en courant alternatif, 50 Hz à 60 Hz, et un courant assigné ne dépassant pas 63 A en triphasé ou 70 A en monophasé, et sont destinés à la charge conductive des véhicules électriques. Le présent document couvre les appareils d’interface basique pour l’alimentation de véhicules tels que spécifiés dans l’IEC 62196-1:2022. Cette troisième édition annule et remplace la deuxième édition parue en 2016. Cette édition constitue une révision technique. Cette édition inclut les modifications techniques majeures suivantes par rapport à l’édition précédente:
les exigences d’interchangeabilité ont été supprimées du titre de la Partie 2;
alignement sur l’IEC 62196-1:2022 et l’IEC 62196-3:2022;
alignement sur l’IEC 61851-1:2017.
Vtiči, vtičnice, konektorji in uvodnice na vozilih - Kabelsko napajanje električnih vozil - 2. del: Zahteve za dimenzijsko skladnost za pribor s trni in cevastimi kontakti za izmenični tok (a.c.) (IEC 62196-2:2022)
Ta del standarda IEC 62196 se uporablja za vtiče, vtičnice, konektorje in uvodnice na električnih vozilih s trni in cevastimi kontakti standardiziranih oblik (v nadaljnjem besedilu: »priključki«). Njihova nominalna nazivna obratovalna napetost je manjša od 480 V izmenične napetosti, 50 Hz do 60 Hz, nazivni tok pa manjši od 63 A pri treh fazah ali 70 A pri eni fazi, za uporabo pri sistemih za polnjenje električnih vozil po kablu.
Ta dokument zajema osnovne vmesniške priključke za napajanje vozil, kot je opredeljeno v standardu IEC 62196-1.
OPOMBA 1: Izraz »električna cestna vozila (EV)« vključuje vsa cestna vozila, vključno s hibridnimi cestnimi vozili z možnostjo polnjenja prek navadne vtičnice (PHEV), ki vso energijo ali njen del pridobijo iz sistemov za shranjevanje energije z možnostjo ponovnega polnjenja (RESS) v vozilu.
Ti priključki so namenjeni za uporabo pri tokokrogih, navedenih v standardu IEC 61851-1:2017, ki delujejo pri različnih napetostih in frekvencah in lahko vključujejo malo napetost (ELV) in komunikacijske signale.
Uporaba teh priključkov za dvosmerni prenos moči je še v fazi preučevanja.
Ta dokument se uporablja za priključke za uporabo pri temperaturi okolja med –30 °C in +40 °C.
OPOMBA 2: V naslednji državi lahko veljajo druge zahteve glede nižje temperature: NO.
OPOMBA 3: V naslednji državi velja –35 °C: SE.
Ti priključki se lahko priključijo samo na kable z vodniki iz bakra ali bakrove zlitine.
Uvodnice in konektorji na vozilih, opisanih v tem dokumentu, se lahko uporabljajo pri polnjenju v načinu 1, 2 in 3, primera B in C. Vtičnice in vtiči za električna vozila iz tega dokumenta se lahko uporabljajo samo pri načinu polnjenja 3, primera A in B.
Načini in dovoljeni priključki so določeni v standardu IEC 61851-1:2017.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-maj-2023
Nadomešča:
SIST EN 62196-2:2017
Vtiči, vtičnice, konektorji in uvodnice na vozilih - Kabelsko napajanje električnih
vozil - 2. del: Zahteve za dimenzijsko skladnost za pribor s trni in cevastimi
kontakti za izmenični tok (a.c.) (IEC 62196-2:2022)
Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of
electric vehicles - Part 2: Dimensional compatibility requirements for AC pin and contact-
tube accessories (IEC 62196-2:2022)
Stecker, Steckdosen, Fahrzeugkupplungen und Fahrzeugstecker - Konduktives Laden
von Elektrofahrzeugen - Teil 2: Maßliche Kompatibilitätsanforderungen an
Wechselspannungssteckvorrichtungen mit Stiften und Buchsen (IEC 62196-2:2022)
Fiches, socles de prise de courant, prises mobiles de véhicule et socles de connecteurs
de véhicule - Charge conductive des véhicules électriques - Partie 2: Exigences
dimensionnelles de compatibilité pour les appareils à broches et alvéoles pour courant
alternatif (IEC 62196-2:2022)
Ta slovenski standard je istoveten z: EN IEC 62196-2:2022
ICS:
29.120.30 Vtiči, vtičnice, spojke Plugs, socket-outlets,
couplers
43.120 Električna cestna vozila Electric road vehicles
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN IEC 62196-2
NORME EUROPÉENNE
EUROPÄISCHE NORM November 2022
ICS 29.120.30; 43.120 Supersedes EN 62196-2:2017
English Version
Plugs, socket-outlets, vehicle connectors and vehicle inlets -
Conductive charging of electric vehicles - Part 2: Dimensional
compatibility requirements for AC pin and contact-tube
accessories
(IEC 62196-2:2022)
Fiches, socles de prise de courant, prises mobiles de Stecker, Steckdosen, Fahrzeugkupplungen und
véhicule et socles de connecteurs de véhicule - Charge Fahrzeugstecker - Konduktives Laden von
conductive des véhicules électriques - Partie 2: Exigences Elektrofahrzeugen - Teil 2: Maßliche
dimensionnelles de compatibilité pour les appareils à Kompatibilitätsanforderungen an
broches et alvéoles pour courant alternatif Wechselspannungssteckvorrichtungen mit Stiften und
(IEC 62196-2:2022) Buchsen
(IEC 62196-2:2022)
This European Standard was approved by CENELEC on 2022-11-23. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 62196-2:2022 E
European foreword
The text of document 23H/502/FDIS, future edition 3 of IEC 62196-2, prepared by SC 23H "Plugs,
Socket-outlets and Couplers for industrial and similar applications, and for Electric Vehicles" of
IEC/TC 23 "Electrical accessories" was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN IEC 62196-2:2022.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2023-08-23
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2025-11-23
document have to be withdrawn
This document supersedes EN 62196-2:2017 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a Standardization Request given to CENELEC by the
European Commission and the European Free Trade Association.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 62196-2:2022 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standard indicated:
IEC 61851 (series) NOTE Harmonized as EN IEC 61851 (series)
IEC 62196-3:2022 NOTE Harmonized as EN IEC 62196-3:2022 (not modified)
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cenelec.eu.
Annex ZA of EN IEC 62196-1:2022 applies, except as follows. Add the following reference:
Publication Year Title EN/HD Year
IEC 62196-1 2022 Plugs, socket-outlets, vehicle connectors and - -
vehicle inlets - Conductive charging of
electric vehicles - Part 1: General
requirements
IEC 62196-2 ®
Edition 3.0 2022-10
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Plugs, socket-outlets, vehicle connectors and vehicle inlets – Conductive
charging of electric vehicles –
Part 2: Dimensional compatibility requirements for AC pin and contact-tube
accessories
Fiches, socles de prise de courant, prises mobiles de véhicule et socles de
connecteurs de véhicule – Charge conductive des véhicules électriques –
Partie 2: Exigences dimensionnelles de compatibilité pour les appareils à
broches et alvéoles pour courant alternatif
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 29.120.30; 43.120 ISBN 978-2-8322-5931-3
– 2 – IEC 62196-2:2022 © IEC 2022
CONTENTS
FOREWORD . 4
INTRODUCTION . 6
1 Scope . 7
2 Normative references . 7
3 Terms and definitions . 8
4 General . 8
5 Ratings . 8
6 Connection between the power supply and the electric vehicle . 8
7 Classification of accessories . 11
8 Marking . 11
9 Dimensions. 11
10 Protection against electric shock . 12
11 Size and colour of protective earthing and neutral conductors . 12
12 Provisions for earthing . 12
13 Terminals . 13
14 Interlocks . 13
15 Resistance to ageing of rubber and thermoplastic material . 13
16 General construction . 13
17 Construction of EV socket-outlets – General . 13
18 Construction of EV plugs and vehicle connectors . 13
19 Construction of vehicle inlets . 13
20 Degrees of protection . 13
21 Insulation resistance and dielectric strength . 13
22 Breaking capacity . 13
23 Normal operation . 14
24 Temperature rise . 14
25 Flexible cables and their connection . 14
26 Mechanical strength . 14
27 Screws, current-carrying parts and connections . 14
28 Creepage distances, clearances and distances through sealing compound . 14
29 Resistance to heat and to fire . 14
30 Corrosion and resistance to rusting . 14
31 Conditional short-circuit current . 14
32 Electromagnetic compatibility (EMC) . 14
33 Vehicle drive over . 15
34 Thermal cycling . 15
35 Humidity exposure . 15
36 Misalignment . 15
37 Contact endurance test . 15
201 Resistor coding . 15
STANDARD SHEETS . 16
CONFIGURATION TYPE 1 . 16
IEC 62196-2:2022 © IEC 2022 – 3 –
CONFIGURATION TYPE 2 . 27
CONFIGURATION TYPE 3 . 42
Annex A (informative) Legacy drawings from IEC 62196-2:2016 . 61
Bibliography . 66
Table 201 – Overview of the basic vehicle interface, configuration type 1, single phase . 10
Table 202 – Overview of the basic vehicle interface, configuration types 2 and 3, three
phase or single phase . 10
Table 203 – Configuration types and standard sheets . 12
Table 204 – Interoperation of configuration type 2 accessories . 27
– 4 – IEC 62196-2:2022 © IEC 2022
INTERNATIONAL ELECTROTEC
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.