ISO/IEC PAS 16898:2012

Electrically propelled road vehicles -- Dimensions and designation of secondary lithium-ion cells

ISO/IEC PAS 16898:2012 specifies a designation system as well as the shapes and dimensions for secondary lithium-ion cells for integration into battery packs and systems used in electrically propelled road vehicles including the position of the terminals and any over-pressure safety device (OPSD). It is related to cylindrical, prismatic and pouch cells.
The cell designation according to ISO/IEC PAS 16898:2012 is intended to be applied to the cells used for electrically propelled road vehicles. ISO/IEC PAS 16898:2012 does not apply to cells specifically used for mopeds, motorcycles and vehicles not primarily defined as road vehicles, i.e. material handling trucks or forklifts.
The cell dimensions listed in ISO/IEC PAS 16898:2012 are recommended but not restricted for use in passenger cars up to 3,5 t.
The inner design, the cell chemistry, the electrical characteristics and any further properties of the cells are not defined in ISO/IEC PAS 16898:2012.

General Information

• Status: Withdrawn
• Publication Date: 26-Nov-2012
• Withdrawal Date: 21-Jul-2020
• ICS: 01 - GENERALITIES. TERMINOLOGY. STANDARDIZATION. DOCUMENTATION
• ICS: 31.060.30 - Paper and plastics capacitors
• ICS: 43.120 - Electric road vehicles
• Technical Committee: TC 21 - Secondary cells and batteries
• Drafting Committee: JWG 69 Li - TC 21/JWG 69 Li
• Current Stage: WPUB - Publication withdrawn
• Completion Date: 18-Oct-2021

Standards Content (Sample)

PUBLICLY ISO/IEC
AVAILABLE PAS
SPECIFICATION 16898
First edition
2012-12-01
Electrically propelled road vehicles —
Dimensions and designation of
secondary lithium-ion cells
Véhicules routiers à propulsion électrique — Dimensions et
désignation d’accumulateurs lithium-ion
Reference number
ISO/IEC PAS 16898:2012(E)
©
ISO/IEC 2012

---------------------- Page: 1 ----------------------
ISO/IEC PAS 16898:2012(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO/IEC 2012
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any
means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the
address below or ISO’s member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland
ii © ISO/IEC 2012 – All rights reserved

---------------------- Page: 2 ----------------------
ISO/IEC PAS 16898:2012(E)

Contents Page
Foreword .v
Introduction .vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Shape of construction and constituent parts of secondary lithium-ion cell .2
4.1 Shape of construction . 2
4.2 Position of the OPSD . 5
5 Designation of cell . 5
6 Measurement conditions . 6
7 Dimensions for the selected cell design . 6
7.1 General . 6
7.2 Cylindrical cells . 6
7.3 Prismatic cells . 7
7.4 Pouch cells . 9
© ISO/IEC 2012 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO/IEC PAS 16898:2012(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
International Standards are draft
...