SIST EN IEC 60335-2-62:2022
(Main)Household and similar electrical appliances - Safety - Part 2-62: Particular requirements for commercial electric rinsing sinks
Household and similar electrical appliances - Safety - Part 2-62: Particular requirements for commercial electric rinsing sinks
This clause of Part 1 is replaced by the following.
This part of IEC 60335 deals with the safety of electrically operated commercial rinsing
sinks used in commercial kitchens, their rated voltage being not more than 250 V for singlephase appliances connected between one phase and neutral, and 480 V for other appliances.
NOTE 101 These appliances are used for example in kitchens of restaurants, canteens, hospitals and commercial
enterprises such as bakeries, butcheries, etc.
The electrical part of appliances making use of other forms of energy is also within the scope
of this standard.
As far as is practicable, this standard deals with the common hazards presented by these
types of appliances.
NOTE 102 Attention is drawn to the fact that
– for appliances intended to be used in vehicles or on board ships or aircraft, additional requirements can be
necessary;
– for appliances intended to be used in tropical countries, special requirements can be necessary;
– in many countries, additional requirements are specified by the national health authorities, the national
authorities responsible for the protection of labour, the national water supply authorities and similar authorities.
NOTE 103 This standard does not apply to
– appliances designed primarily for sterilizing to clinical standards;
– dishwashers (IEC 60335-2-58);
– appliances designed exclusively for industrial purposes;
– appliances intended to be used in locations where special conditions prevail, such as the presence of a
corrosive or explosive atmosphere (dust, vapour or gas)
Sicherheit elektrischer Geräte für den Hausgebrauch und ähnliche Zwecke - Teil 2-62: Besondere Anforderungen für elektrische Spülbecken für den gewerblichen Gebrauch
Appareils électrodomestiques et analogues - Sécurité - Partie 2-62: Exigences particulières pour les plonges électriques à usages collectif (IEC 60335-2-62:2019)
IEC 60335-2-62:2019 est disponible sous forme de IEC 60335-2-62:2019 RLV qui contient la Norme internationale et sa version Redline, illustrant les modifications du contenu technique depuis l'édition précédente.
L'IEC 60335-2-62:2019 traite de la sécurité des plonges électriques à usage commercial, utilisées dans les cuisines commerciales et dont la tension assignée n'est pas supérieure à 250 V pour les appareils monophasés alimentés entre phase et neutre, et à 480 V pour les autres appareils. Ces appareils sont par exemple utilisés dans les cuisines de restaurants, les cantines, les hôpitaux et les entreprises artisanales, telles que les boulangeries, les boucheries, etc. La partie électrique des appareils utilisant d’autres formes d’énergie relève également du domaine d’application de la présente norme. Dans la mesure du possible, la présente norme traite des dangers ordinaires présentés par ces types d'appareils. L’attention est attirée sur le fait que:
- pour les appareils destinés à être utilisés dans des véhicules ou à bord de navires ou d'avions, des exigences supplémentaires peuvent être nécessaires;
- pour les appareils destinés à être utilisés dans les pays tropicaux, des exigences spéciales peuvent être nécessaires;
- dans de nombreux pays, des exigences supplémentaires sont spécifiées par les organismes nationaux de la santé, par les organismes nationaux responsables de la protection des travailleurs, par les organismes nationaux responsables de l'alimentation en eau et par des organismes similaires.
La présente norme ne s’applique pas:
- aux appareils destinés principalement à la stérilisation conforme aux normes cliniques;
- aux lave-vaisselle (IEC 60335-2-58);
- aux appareils prévus exclusivement pour des usages industriels;
- aux appareils destinés à être utilisés dans des locaux présentant des conditions particulières, telles que la présence d'une atmosphère corrosive ou explosive (poussière, vapeur ou gaz).
Cette quatrième édition annule et remplace la troisième édition parue en 2002 et son Amendement 1:2008. Cette édition constitue une révision technique.
Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente:
- indication des valeurs spécifiques des températures pour les parties accessibles et l’eau dans le cadre de l’alignement du texte sur l’IEC 60335-1, Édition 5, et ses Amendements 1 et 2;
- ajout de l’exigence de l’application de la sonde d’essai 12 pour vérifier l’accès aux parties actives (8.1
Gospodinjski in podobni električni aparati - Varnost - 2-62. del: Posebne zahteve za komercialna električna pomivalna korita
ICS: 91.140.70
To točko 1. dela nadomešča naslednje besedilo.
Ta del standarda IEC 60335 obravnava varnost komercialnih električnih pomivalnih
korit, ki se uporabljajo v komercialnih kuhinjah, pri čemer nazivna napetost ne sme presegati 250 V za enofazne aparate, priključene med fazo in nevtralni vodnik, in 480 V za ostale aparate.
OPOMBA 101: Ti aparati se na primer uporabljajo v kuhinjah restavracij, menz, bolnišnic in trgovskih podjetij, kot so pekarne, mesnice itd.
Tudi električni del aparatov, ki uporabljajo druge vire energije, spada na področje uporabe tega standarda.
Ta standard v največji možni meri obravnava splošne nevarnosti, ki jih predstavljajo tovrstni aparati.
OPOMBA 102: Opozoriti je treba, da:
– so za aparate, ki so namenjeni za uporabo v vozilih ali na krovu ladij ali letal, morda potrebne dodatne zahteve;
– so za aparate, ki so namenjeni za uporabo v tropskih državah, morda potrebne posebne zahteve;
– v številnih državah nacionalni zdravstveni organi, nacionalni organi, odgovorni za varstvo pri delu, nacionalni organi za oskrbo z vodo ter drugi podobni organi določajo dodatne zahteve.
OPOMBA 103: Ta standard se ne uporablja za:
– aparate, ki so primarno zasnovani za sterilizacijo v skladu s kliničnimi standardi;
– pomivalne stroje (IEC 60335-2-58);
– aparate, zasnovane izključno za industrijske namene;
– aparate, ki so namenjeni za uporabo na lokacijah, kjer veljajo posebne razmere, kot je prisotnost korozivne ali eksplozivne atmosfere (prah, hlapi ali plin).
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN IEC 60335-2-62:2022
01-oktober-2022
Nadomešča:
SIST EN 60335-2-62:2003
SIST EN 60335-2-62:2003/A1:2008
Gospodinjski in podobni električni aparati - Varnost - 2-62. del: Posebne zahteve
za komercialna električna pomivalna korita
Household and similar electrical appliances - Safety - Part 2-62: Particular requirements
for commercial electric rinsing sinks
Appareils électrodomestiques et analogues - Sécurité - Partie 2-62: Exigences
particulières pour les plonges électriques à usages collectif (IEC 60335-2-62:2019)
Ta slovenski standard je istoveten z: EN IEC 60335-2-62:2022
ICS:
91.140.70 Sanitarne naprave Sanitary installations
SIST EN IEC 60335-2-62:2022 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN IEC 60335-2-62:2022
---------------------- Page: 2 ----------------------
SIST EN IEC 60335-2-62:2022
EUROPEAN STANDARD EN IEC 60335-2-62
NORME EUROPÉENNE
EUROPÄISCHE NORM July 2022
ICS 97.040.50 Supersedes EN 60335-2-62:2003,
EN 60335-2-62:2003/corrigendum Aug. 2007,
EN 60335-2-62:2003/A1:2008
English Version
Household and similar electrical appliances - Safety - Part 2-62:
Particular requirements for commercial electric rinsing sinks
(IEC 60335-2-62:2019)
Appareils électrodomestiques et analogues - Sécurité - Sicherheit elektrischer Geräte für den Hausgebrauch und
Partie 2-62: Exigences particulières pour les plonges ähnliche Zwecke - Teil 2-62: Besondere Anforderungen für
électriques à usage collectif elektrische Spülbecken für den gewerblichen Gebrauch
(IEC 60335-2-62:2019) (IEC 60335-2-62:2019)
This European Standard was approved by CENELEC on 2022-05-27. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 60335-2-62:2022 E
---------------------- Page: 3 ----------------------
SIST EN IEC 60335-2-62:2022
EN IEC 60335-2-62:2022 (E)
European foreword
This document (EN IEC 60335-2-62:2022) consists of the text of IEC 60335-2-62:2019, prepared by
IEC/TC 61 "Safety of household and similar electrical appliances"
The following dates are fixed:
• latest date by which this document has to be implemented (dop) 2023-05-27
at national level by publication of an identical national
standard or by endorsement
• latest date by which the national standards conflicting with (dow) 2025-05-27
this document have to be withdrawn
This document supersedes EN 60335-2-62:2003 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a Standardization Request given to CENELEC by the
European Commission and the European Free Trade Association.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 60335-2-62:2019 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following note has to be added for the standard indicated:
IEC 60335-2-58 NOTE Harmonized as EN 60335-2-58
2
---------------------- Page: 4 ----------------------
SIST EN IEC 60335-2-62:2022
EN IEC 60331-2-60:2022 (E)
Annex ZC
(normative)
Normative references to international publications with their
corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the
relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cenelec.eu.
The Annex ZC of Part 1 is applicable except as follows.
Addition:
Publication Year Title EN/HD Year
IEC 60584-1 - Thermocouples – Part 1: EN 60584-1 2013
EMF specifications and tolerances
ISO 898-1 - Mechanical properties of fasteners made of EN ISO 898-1 2013
carbon steel and alloy steel – Part 1: Bolts,
screws and studs with specified property
classes - Coarse thread and fine pitch thread
+ AC 2013
ISO 3506-1 - Mechanical properties of corrosion-resistant EN ISO 3506-1 2020
stainless steel fasteners – Part 1: Bolts,
screws and studs
ISO 3506-2 - Mechanical properties of corrosion-resistant EN ISO 3506-2 2020
stainless steel fasteners – Part 2: Nuts
ISO 3506-3 - Mechanical properties of corrosion-resistant EN ISO 3506-3 2009
stainless steel fasteners – Part 3: Set screws
and similar fasteners not under tensile stress
ISO 3506-4 - Mechanical properties of corrosion-resistant EN ISO 3506-4 2009
stainless steel fasteners – Part 4: Tapping
screws
3
---------------------- Page: 5 ----------------------
SIST EN IEC 60335-2-62:2022
---------------------- Page: 6 ----------------------
SIST EN IEC 60335-2-62:2022
IEC 60335-2-62
®
Edition 4.0 2019-12
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Household and similar electrical appliances – Safety –
Part 2-62: Particular requirements for commercial electric rinsing sinks
Appareils électrodomestiques et analogues – Sécurité –
Partie 2-62: Exigences particulières pour les plonges électriques à usage
collectif
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 97.040.50 ISBN 978-2-8322-7670-9
Warning! Make sure that you obtained this publication from an authorized distributor.
Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 7 ----------------------
SIST EN IEC 60335-2-62:2022
– 2 – IEC 60335-2-62:2019 © IEC 2019
CONTENTS
FOREWORD . 4
INTRODUCTION . 7
1 Scope . 8
2 Normative references . 8
3 Terms and definitions . 9
4 General requirement . 10
5 General conditions for the tests . 10
6 Classification . 10
7 Marking and instructions . 10
8 Protection against access to live parts . 12
9 Starting of motor-operated appliances . 12
10 Power input and current . 12
11 Heating . 12
12 Void . 14
13 Leakage current and electric strength at operating temperature . 14
14 Transient overvoltages . 14
15 Moisture resistance . 14
16 Leakage current and electric strength . 15
17 Overload protection of transformers and associated circuits . 15
18 Endurance . 15
19 Abnormal operation . 16
20 Stability and mechanical hazards . 16
21 Mechanical strength . 16
22 Construction . 16
23 Internal wiring . 17
24 Components . 17
25 Supply connection and external flexible cords . 17
26 Terminals for external conductors . 18
27 Provision for earthing . 18
28 Screws and connections . 18
29 Clearances, creepage distances and solid insulation . 19
30 Resistance to heat and fire . 19
31 Resistance to rusting . 20
32 Radiation, toxicity and similar hazards . 20
Annexes . 22
Annex N (normative) Proof tracking test . 22
Annex P (informative) Guidance for the application of this standard to appliances
used in tropical climates . 23
Bibliography . 24
Figure 101 – Probe for measuring surface temperatures . 20
---------------------- Page: 8 ----------------------
SIST EN IEC 60335-2-62:2022
IEC 60335-2-62:2019 © IEC 2019 – 3 –
Figure 102 – Splash apparatus . 21
Table 101 – Maximum temperature rises for specified external accessible surfaces
under normal operating conditions . 13
Table 102 – Assembling torques for screwed connections providing earthing continuity . 19
---------------------- Page: 9 ----------------------
SIST EN IEC 60335-2-62:2022
– 4 – IEC 60335-2-62:2019 © IEC 2019
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES –
SAFETY –
Part 2-62: Particular requirements
for commercial electric rinsing sinks
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60335-2-62 has been prepared by IEC technical committee 61:
Safety of household and similar electrical appliances.
This fourth edition cancels and replaces the third edition published in 2002 and its
Amendment 1:2008. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous
edition:
– indicates specific values for temperatures for accessible parts and water and aligns the
text with IEC 60335-1, Edition 5, and its Amendments 1 and 2;
– requires the application of test probe 12 for the verification of access to live parts (8.101);
– foresees the use of a specific test probe for the measurements of temperatures of
accessible surfaces (11.3);
---------------------- Page: 10 ----------------------
SIST EN IEC 60335-2-62:2022
IEC 60335-2-62:2019 © IEC 2019 – 5 –
– washing vessel (11.8);
– modification on leakage current defining the value for appliances with a power
consumption less than 1 kW (13.2);
– addition of specific requirements concerning types of screws to be used for electrical
connections and connections for earth continuity (Clause 28);
– addition of informative Annex P dealing with leakage currents for appliances used in
tropical climates.
The text of this International Standard is based on the following documents:
FDIS Report on voting
61/5938/FDIS 61/5950/RVD
Full information on the voting for the approval of this International Standard can be found in
the report on voting indicated in the above table.
This document has been drafted in accordance with the ISO/IEC Directives, Part 2.
A list of all parts of the IEC 60335 series, under the general title: Household and similar
electrical appliances – Safety, can be found on the IEC website.
This part 2 is to be used in conjunction with the latest edition of IEC 60335-1 and its
amendments. It was established on the basis of the fifth edition (2010) of that standard.
NOTE 1 When “Part 1” is mentioned in this standard, it refers to IEC 60335-1.
This part 2 supplements or modifies the corresponding clauses in IEC 60335-1, so as to
convert that publication into the IEC standard: Particular requirements for commercial electric
rinsing sinks.
When a particular subclause of Part 1 is not mentioned in this part 2, that subclause applies
as far as is reasonable. When this standard states “addition”, “modification” or “replacement”,
the relevant text in Part 1 is to be adapted accordingly.
NOTE 2 The following numbering system is used:
– subclauses, tables and figures that are numbered starting from 101 are additional to those in Part 1;
– unless notes are in a new subclause or involve notes in Part 1, they are numbered starting from 101, including
those in a replaced clause or subclause;
– additional annexes are lettered AA, BB, etc.
NOTE 3 The following print types are used:
– requirements: in roman type;
– test specifications: in italic type;
– notes: in small roman type.
Words in bold in the text are defined in Clause 3. When a definition concerns an adjective, the adjective and the
associated noun are also in bold.
---------------------- Page: 11 ----------------------
SIST EN IEC 60335-2-62:2022
– 6 – IEC 60335-2-62:2019 © IEC 2019
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under "http://webstore.iec.ch" in the data related to
the specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
NOTE 4 The attention of National Committees is drawn to the fact that equipment manufacturers and testing
organizations may need a transitional period following publication of a new, amended or revised IEC publication in
which to make products in accordance with the new requirements and to equip themselves for conducting new or
revised tests.
It is the recommendation of the committee that the content of this publication be adopted for implementation
nationally not earlier than 12 months from the date of publication.
---------------------- Page: 12 ----------------------
SIST EN IEC 60335-2-62:2022
IEC 60335-2-62:2019 © IEC 2019 – 7 –
INTRODUCTION
It has been assumed in the drafting of this International Standard that the execution of its
provisions is entrusted to appropriately qualified and experienced persons.
This standard recognizes the internationally accepted level of protection against hazards such
as electrical, mechanical, thermal, fire and radiation of appliances when operated as in
normal use taking into account the manufacturer's instructions. It also covers abnormal
situations that can be expected in practice and takes into account the way in which
electromagnetic phenomena can affect the safe operation of appliances.
This standard takes into account the requirements of IEC 60364 as far as possible so that
there is compatibility with the wiring rules when the appliance is connected to the supply
mains. However, national wiring rules may differ.
If an appliance within the scope of this standard also incorporates functions that are covered
by another part 2 of IEC 60335, the relevant part 2 is applied to each function separately, as
far as is reasonable. If applicable, the influence of one function on the other is taken into
account.
When a part 2 standard does not include additional requirements to cover hazards dealt with
in Part 1, Part 1 applies.
NOTE 1 This means that the technical committees responsible for the part 2 standards have determined that it is
not necessary to specify particular requirements for the appliance in question over and above the general
requirements.
This standard is a product family standard dealing with the safety of appliances and takes
precedence over horizontal and generic standards covering the same subject.
NOTE 2 Horizontal and generic standards covering a hazard are not applicable since they have been taken into
consideration when developing the general and particular requirements for the IEC 60335 series of standards. For
example, in the case of temperature requirements for surfaces on many appliances, generic standards, such as
ISO 13732-1 for hot surfaces, are not applicable in addition to Part 1 or part 2 standards.
An appliance that complies with the text of this standard will not necessarily be considered to
comply with the safety principles of the standard if, when examined and tested, it is found to
have other features that impair the level of safety covered by these requirements.
An appliance employing materials or having forms of construction differing from those detailed
in the requirements of this standard may be examined and tested according to the intent of
the requirements and, if found to be substantially equivalent, may be considered to comply
with the standard.
---------------------- Page: 13 ----------------------
SIST EN IEC 60335-2-62:2022
– 8 – IEC 60335-2-62:2019 © IEC 2019
HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES –
SAFETY –
Part 2-62: Particular requirements
for commercial electric rinsing sinks
1 Scope
This clause of Part 1 is replaced by the following.
This part of IEC 60335 deals with the safety of electrically operated commercial rinsing
sinks used in commercial kitchens, their rated voltage being not more than 250 V for single-
phase appliances connected between one phase and neutral, and 480 V for other appliances.
NOTE 101 These appliances are used for example in kitchens of restaurants, canteens, hospitals and commercial
enterprises such as bakeries, butcheries, etc.
The electrical part of appliances making use of other forms of energy is also within the scope
of this standard.
As far as is practicable, this standard deals with the common hazards presented by these
types of appliances.
NOTE 102 Attention is drawn to the fact that
– for appliances intended to be used in vehicles or on board ships or aircraft, additional requirements can be
necessary;
– for appliances intended to be used in tropical countries, special requirements can be necessary;
– in many countries, additional requirements are specified by the national health authorities, the national
authorities responsible for the protection of labour, the national water supply authorities and similar authorities.
NOTE 103 This standard does not apply to
– appliances designed primarily for sterilizing to clinical standards;
– dishwashers (IEC 60335-2-58);
– appliances designed exclusively for industrial purposes;
– appliances intended to be used in locations where special conditions prevail, such as the presence of a
corrosive or explosive atmosphere (dust, vapour or gas).
2 Normative references
This clause of Part 1 is applicable except as follows.
Addition:
IEC 60584-1, Thermocouples – Part 1: EMF specifications and tolerances
ISO 898-1, Mechanical properties of fasteners made of carbon steel and alloy steel – Part 1:
Bolts, screws and studs with specified property classes – Coarse thread and fine pitch thread
ISO 3506-1, Mechanical properties of corrosion-resistant stainless steel fasteners – Part 1:
Bolts, screws and studs
ISO 3506-2, Mechanical properties of corrosion-resistant stainless steel fasteners – Part 2:
Nuts
---------------------- Page: 14 ----------------------
SIST EN IEC 60335-2-62:2022
IEC 60335-2-62:2019 © IEC 2019 – 9 –
ISO 3506-3, Mechanical properties of corrosion-resistant stainless steel fasteners – Part 3:
Set screws and similar fasteners not under tensile stress
ISO 3506-4, Mechanical properties of corrosion-resistant stainless steel fasteners – Part 4:
Tapping screws
3 Terms and definitions
This clause of Part 1 is applicable except as follows.
3.1 Definitions relating to physical characteristics
3.1.4
NOTE 101 The rated power input is the sum of the power inputs of all the individual elements in the appliance
that can be on at one time; where there are several such combinations possible, that giving the highest power input
is used in determining the rated power input.
3.1.9 Replacement:
normal operation
operation of the appliance under the following conditions:
Appliances are operated in accordance with the instructions, with all the controls intended to
be operated by the user adjusted to their maximum setting. Lids and covers, if any, are placed
in their intended position.
Appliances intended to be filled by hand or by a manually operated tap are filled to the
indicated level.
Where several levels are marked, that giving the most unfavourable conditions is used.
Appliances intended to be filled automatically are connected to a water supply having the
pressure designated by the manufacturer.
Where the manufacturer specifies a range of pressures, the pressure is adjusted to that giving
the most unfavourable conditions.
The temperature of the water supplied is 15 °C ± 5 °C.
Motors incorporated in the appliance are operated in the intended manner, under the most
severe conditions that can be expected in normal use taking into account the instructions.
3.5 Definitions relating to types of appliances
3.5.101
rinsing sink
an appliance intended for rinsing crockery, cutlery chopsticks and utensils with water heated
in the appliance itself
3.8 Definitions relating to miscellaneous matters
3.8.101
indicated level
a mark on the appliance to indicate the maximum liquid level for correct operation
3.8.102
installation wall
a special fixed construction containing supply facilities for appliances installed in conjunction
with it
---------------------- Page: 15 ----------------------
SIST EN IEC 60335-2-62:2022
– 10 – IEC 60335-2-62:2019 © IEC 2019
4 General requirement
This clause of Part 1 is applicable.
5 General conditions for the tests
This clause of Part 1 is applicable except as follows.
5.10 Addition:
Appliances intended for installation in a bank of other appliances and appliances intended to
be fixed to an installation wall are enclosed to obtain protection against electric shock and
harmful ingress of water equivalent to that when installed in accordance with the instructions
provided with the appliance.
NOTE 101 Appropriate enclosures or additional appliances can be needed for test purposes.
5.101 Appliances are tested as heating appliances, even if they incorporate a motor.
5.102 Appliances, when assembled in combination with or incorporating other appliances,
are tested in accordance with the requirements of this standard. The other appliances are
operated simultaneously in accordance with the requirements of the relevant standards.
6 Classification
This clause of Part 1 is applicable except as follows.
6.1 Replacement:
Appliances shall be class I with respect to protection agains
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.