International gear notation -- Symbols for geometrical data

Notation internationale des engrenages -- Symboles géométriques

La présente Norme internationale spécifie des symboles géométriques pour l'emploi dans la notation des engrenages. Elle comporte deux listes, à savoir : -- d'une part, les symboles principaux, composés d'une seule lettre de base (voir tableau 1); -- d'autre part, des indices à ajouter, s'il y a lieu, aux symboles principaux, pour exprimer telle ou telle qualification du terme en question (voir tableaux 2, 3 et 4).

Mednarodne označbe za zobnike - Simboli za geometrijske veličine

General Information

Status
Published
Publication Date
31-Aug-2000
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
01-Sep-2000
Due Date
01-Sep-2000
Completion Date
01-Sep-2000

RELATIONS

Buy Standard

Standard
ISO 701:1998 - International gear notation -- Symbols for geometrical data
English language
4 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 701:1998 - Notation internationale des engrenages -- Symboles géométriques
French language
4 pages
sale 15% off
Preview
sale 15% off
Preview
Standard – translation
SIST ISO 701:2000
Slovenian language
7 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day

Standards Content (sample)

INTERNATIONAL ISO
STANDARD 701
Second edition
1998-05-15
International gear notation — Symbols for
geometrical data
Notation internationale des engrenages — Symboles géométriques
Reference number
ISO 701:1998(E)
---------------------- Page: 1 ----------------------
ISO 701:1998(E)
Foreword
ISO (the International Organization for Standardization) is a wordwide
federation of national standards bodies (ISO member bodies). The work of
preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which
a technical committee has been established has the right to be represented
on that committee. International organizations, governmental and non-
governmental, in liaison with ISO, also take part in the work. ISO
collaborates closely with the International Electrotechnical Commission
(IEC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are
circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting
a vote.
International Standard ISO 701 was prepared by Technical Committee
Gears Nomenclature and worm gears
ISO/TC 60, , Subcommittee SC 1, .
This second edition of ISO 701 cancels and replaces the first edition
(ISO 701:1976), which has been technically revised.
© ISO 1998

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced

or utilized in any form or by any means, electronic or mechanical, including photocopying and

microfilm, without permission in writing from the publisher.
International Organization for Standardization
Case postale 56 • CH-1211 Genève 20 • Switzerland
Internet iso@iso.ch
Printed in Switzerland
---------------------- Page: 2 ----------------------
ISO ISO 701:1998(E)
Introduction
The symbols in this International Standard are defined for use in relation to
the principal geometrical terms defined in ISO 1122-1:1998, Vocabulary of
gear terms — Part 1: Definitions related to geometry.
Consequently, it is important:
— that these symbols be used in national standards and, where
appropriate, in other national documents in order to facilitate the
understanding of documents which are exchanged between countries;
— to use for geometrical data only those combinations of letters which
are given in the tables of this International Standard, in order to avoid
any risk of confusion with symbols relating to other gear data, which
may be determined later.
iii
---------------------- Page: 3 ----------------------
INTERNATIONAL STANDARD ISO ISO 701:1998(E)
International gear notation — Symbols for geometrical data
1 Scope

This International Standard specifies geometrical symbols for use in notation of gear data. It comprises two lists:

— the principal symbols, consisting of a single basic letter (see table 1); and

— subscripts to be used as necessary to qualify principal symbols (see tables 2, 3 and 4).

2 Symbols
2.1 Derivation of geometrical symbols
The principal rules are as follows:

a) symbols consist of a principal symbol which can be followed by one or more subscripts and possibly a

superscript;

b) the principal symbol is either a single uppercase or lowercase letter. The letter should b

...

NORME ISO
INTERNATIONALE 701
Deuxième édition
1998-05-15
Notation internationale des engrenages —
Symboles géométriques
International gear notation — Symbols for geometrical data
Numéro de référence
ISO 701:1998(F)
---------------------- Page: 1 ----------------------
ISO 701:1998(F)
Avant-propos

L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux de

normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général confiée aux

comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit de faire partie du comité

technique créé à cet effet. Les organisations internationales, gouvernementales et non gouvernementales, en

liaison avec l'ISO, participent également aux travaux. L'ISO collabore étroitement avec la Commission

électrotechnique internationale (CEI) en ce qui concerne la normalisation électrotechnique.

Les projets de Normes internationales adoptés par les comités techniques sont soumis aux comités membres pour

vote. Leur publication comme Normes internationales requiert l'approbation de 75 % au moins des comités

membres votants.

La Norme internationale ISO 701 a été élaborée par le comité technique ISO/TC 60, Engrenages, sous-comité SC 1,

Nomenclature et engrenages à vis.

Cette deuxième édition annule et remplace la première édition (ISO 701:1976), dont elle constitue une révision

technique.
© ISO 1998

Droits de reproduction réservés. Sauf prescription différente, aucune partie de cette publi-

cation ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun pro-

cédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord

écrit de l'éditeur.
Organisation internationale de normalisation
Case postale 56 • CH-1211 Genève 20 • Suisse
Internet iso@iso.ch
Imprimé en Suisse
---------------------- Page: 2 ----------------------
© ISO
ISO 701:1998(F)
Introduction

Les symboles de la présente Norme internationale sont définis pour être utilisés en relation avec les principaux termes

géométriques définis dans l’ISO 1122-1:1998, Vocabulaire des engrenages — Partie 1: Définitions géométriques.

Il importe par conséquent:

— d’utiliser ces symboles dans les normes nationales et dans les autres documents nationaux, si appropriés, afin

d'assurer un véritable langage international de notations facilitant les échanges de documents d'un pays à l'autre;

— de n'utiliser, pour les données géométriques, que les combinaisons des lettres faisant l'objet des tableaux de la

présente Norme internationale, de façon à éviter tout risque de confusion avec les notations à prévoir ultérieurement

pour d'autres données relatives aux engrenages.
iii
---------------------- Page: 3 ----------------------
NORME INTERNATIONALE © ISO ISO 701:1998(F)
Notation internationale des engrenages — Symboles géométriques
1 Domaine d’application

La présente Norme internationale spécifie des symboles géométriques pour l'emploi dans la notation des engrenages.

Elle comporte deux listes, à savoir:

— d'une part, les symboles principaux, composés d'une seule lettre de base (voir tableau 1);

— d'autre part, des indices à ajouter, s'il y a lieu, aux symboles principaux, pour exprimer telle ou telle qualification du

terme en question (voir tableaux 2, 3 et 4).
2 Symboles
2.1 Dérivation des symboles géométriques
Les règles principales sont définies comme suit:

a) les symboles sont composés d'un symbole principal qui peut être suivi par un ou plusieurs indices, et par un

éventuel exposant;

b) le symbole principal est indifféremment une lettre majuscule ou minuscule. Cette lettre est une lettre

...

SL OVENSKI SIST ISO 701
prva izdaja
STANDARD
september 2000
Mednarodne označbe za zobnike - Simboli za geometrijske veličine
(istoveten ISO 701:1998)
International gear notation - Symbols for geometrical data
Notation internationale des engrenages - Symboles géométriques
Deskriptorji: zobniki, geometrijske veličine, terminologija, označbe
Referenčna številka
ICS 01.080.30; 21.200 SIST ISO 701:2000 (sl)
Nadaljevanje na straneh 2 do 8

© Standard je založil in izdal Urad Republike Slovenije za standardizacijo in meroslovje pri Ministrstvu za znanost in tehnologijo.

Razmnoževanje ali kopiranje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST ISO 701 : 2000
NACIONALNI UVOD

Standard SIST ISO 701 (sl), Mednarodne označbe za zobnike - Simboli za geometrijske veličine, prva

izdaja, 2000, ima status slovenskega standarda in je istoveten mednarodnemu standardu

ISO 701 (en), International gear notation - Symbols for geometrical data, Second edition, 1998-05-15.

NACIONALNI PREDGOVOR

Mednarodni standard ISO 701:1998 je pripravil tehnični odbor Mednarodne organizacije za

standardizacijo ISO/TC 60 Zobniki, pododbor SC 1 Označbe in polžasta gonila.

Odločitev za prevzem tega standarda po metodi prevoda je dne 1998-06-17 sprejel tehnični odbor

USM/TC SEL Strojni elementi.
Ta slovenski standard je dne 2000-03-27 odobril direktor USM.
OPOMBI
- Povsod, kjer se v besedilu standarda uporablja izraz “mednarodni standard”, v
SIST ISO 701:2000 to pomeni “slovenski standard”.
- Nacionalni uvod in nacionalni predgovor nista sestavni del standarda.
---------------------- Page: 2 ----------------------
SIST ISO 701 : 2000
VSEBINA Stran

Uvod ....................................................................................................................................................... 4

1 Namen standarda ................................................................................................................................. 5

2 Simboli .................................................................................................................................................. 5

---------------------- Page: 3 ----------------------
SIST ISO 701 : 2000
Uvod

Označbe v tem standardu so izbrane skladno h geometrijskim veličinam, ki so definirane v standardu

SIST ISO 1122-1:1983, Terminološki slovar za zobniške prenosnike - 1.del: Geometrijske definicije.

S tem v zvezi je pomembno:

- da se te označbe uporabljajo v nacionalnih standardih in nacionalnih dokumentih z namenom, da

bi olajšali razumevanje med uporabniki različnih držav;

- da se za označevanje geometrijskih veličin uporabljajo le tiste kombinacije črk, ki so podane v

preglednicah tega mednarodnega standarda, da bi se izognili zamenjavi z označbami, povezanih z

drugimi zobniškimi podatki, ki utegnejo biti določeni pozneje.
---------------------- Page: 4 ----------------------
SIST ISO 701 : 2000
Mednarodne označbe za zobnike – Simboli za geometrijske veličine
1 Namen standarda

Ta mednarodni standard določa geometrične simbole za uporabo in označevanje zobniških podatkov.

Obsega dva seznama:
- osnovne simbole, ki so označeni z eno samo črko (glej preglednico 1); in

- indekse, ki se uporabljajo in so potrebni za podrobno opredelitev osnovnih simbolov (glej

preglednice 2,3 in 4).
2 Simboli
2.1 Izpeljava simbolov geometrijskih veličin
Osnovna pravila:

a) simboli kot celota so sestavljeni iz osnovnega simbola, ki mu je dodan eden ali več podpisanih,

lahko pa tudi nadpisanih indeksov;

b) osnovni simbol je lahko velika ali mala črka abecede. Črke naj bodo iz latinice ali iz grške

abecede v kurzivni pisavi;

c) numerični indeks je lahko številka, decimalno število ali rimska številka. Noben simbol naj ne

vsebuje več kot en numerični indeks;

d) vsi podpisani indeksi naj bodo pisani na isti črti, toda pod črto osnovnih simbolov;

e) izogibati se je treba obkroženih (uokvirjenih) označb (nadpisanih in podpisanih), nadpisanih

označb, razen eksponentov, podpisanih in nadpisanih predpon, podpisanih in nadpisanih označb

v drugem redu in vejic.
2.2 Osnovni simboli geometrijskih veličin

Najpogosteje uporabljani simboli geometrijskih veličin so našteti v preglednici 1.

2.3 Osnovni indeksi

Enak indeks ima lahko različen pomen; to je odvisno od simbola, kateremu pripada indeks. Največkrat

uporabljani indeksi so našteti v pregledni
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.