Connections for fluid power and general use - Ports and stud ends with ISO 261 metric threads and O-ring sealing - Part 4: Dimensions, design, test methods and requirements for external hex and internal hex port plugs (ISO 6149-4:2017)

This document specifies dimensions and performance requirements for external hex and internal hex
port plugs for use with ISO 6149-1 ports.
Port plugs in accordance with this document can be used at working pressures up to 63 MPa (630 bar1)).
The permissible working pressure depends upon the plug end size, materials, design, working
conditions, application, etc.
Conformance to the dimensional information in this document does not guarantee rated performance.
Each manufacturer is expected to perform testing according to the specification contained in this
document to assure that components comply with the performance ratings.
WARNING — The use of stud ends conforming to this document with ports conforming to the
relevant parts of ISO 1179, ISO 9974 and ISO 11926 could lead to a hazardous situation.

Leitungsanschlüsse für Fluidtechnik und allgemeine Anwendung - Einschraublöcher und Einschraubzapfen mit metrischem Gewinde nach ISO 261 und O-Ring-Abdichtung - Teil 4: Maße, Konstruktion, Prüfverfahren und Anforderungen an Verschlussschrauben mit Außen- oder Innen-Sechskant (ISO 6149-4:2017)

Dieses Dokument legt die Maße für und die Leistungsanforderungen an Verschlussschrauben mit Außen- oder Innen-Sechskant für die Verwendung in Einschraublöchern nach ISO 6149-1 fest.
Einschraubzapfen nach diesem Dokument können bei Arbeitsdrücken bis 63 MPa (630 bar1)) verwendet werden. Der zulässige Arbeitsdruck ist abhängig von der Größe des Einschraubzapfens, den Werkstoffen, der Konstruktion, den Betriebsbedingungen, dem Anwendungsfall usw.
Eine Übereinstimmung mit den Maßangaben in diesem Dokument stellt keine Gewährleistung für die Nennleistung dar. Von jedem Hersteller wird erwartet, dass er die Prüfungen nach den in diesem Dokument enthaltenen Festlegungen durchführt, um sicherzustellen, dass die Bauteile den Leistungsangaben entsprechen.
WARNUNG — Die Verwendung von Einschraubzapfen entsprechend diesem Dokument mit Einschraublöchern entsprechend den relevanten Teilen der ISO 1179, ISO 9974 und ISO 11926 könnte zu einer gefährlichen Situation führen.

Raccordements pour transmissions hydrauliques et applications générales - Orifices et éléments mâles à filetage métrique ISO 261 et joint torique - Partie 4: Dimensions, conception, méthodes d'essai et exigences des bouchons d'orifice à six pans externes et à six pans internes (ISO 6149-4:2017)

ISO 6149-4:2017 spécifie les dimensions et les exigences de performance des bouchons d'orifice à six pans externes et à six pans internes destinés à être utilisés avec les orifices ISO 6149‑1.
Les bouchons d'orifice conformes au présent document peuvent être utilisés jusqu'à des pressions d'utilisation de 63 MPa (630 bar [1]). La pression d'utilisation admissible dépend de la dimension du bouchon, des matériaux, de la conception, des conditions d'utilisation, de l'application, etc.
La conformité aux informations dimensionnelles du présent document ne garantit pas les performances nominales. Il est attendu de chaque fabricant qu'il effectue des essais conformes aux spécifications contenues dans le présent document pour s'assurer que les composants satisfont aux performances nominales.
AVERTISSEMENT: L'utilisation d'éléments mâles conformes au présent document avec des orifices conformes aux parties pertinentes des normes ISO 1179, ISO 9974 et ISO 11926 peut engendrer une situation dangereuse.
[1] 1 bar = 0,1 MPa = 105 Pa; 1 MPa = 1 N/mm2.

Priključki v fluidni tehniki in za splošno uporabo - Vhodi in ravni zaključki z navoji po ISO 261 in tesnilkami O - 4. del: Mere, konstrukcija, preskusne metode ter zahteve za zunanje in notranje čepe (ISO 6149-4:2017)

Ta dokument določa mere in zahtevane lastnosti za zunanje in notranje čepe za uporabo z vhodi standarda ISO 6149-1.
Čepi v skladu s tem dokumentom se lahko uporabljajo pri delovnem tlaku do 63 MPa (630 barov1).
Dovoljeni delovni tlak je odvisen od velikosti konca čepa, uporabljenih materialov, oblike, delovnih pogojev, načina uporabe itd.
Skladnost z informacijami o merah v tem dokumentu ne zagotavlja nazivne zmogljivosti.
Od vsakega proizvajalca se pričakuje, da bo opravil preskušanje v skladu s specifikacijami v tem dokumentu, da zagotovi skladnost komponent z ocenami zmogljivosti.
OPOZORILO: Uporaba ravnih zaključkov, ki so skladni s tem dokumentom, z vhodi, ki so v skladu z ustreznimi deli standardov ISO 1179, ISO 9974 in ISO 11926, lahko privede do nevarne situacije.

General Information

Status
Published
Public Enquiry End Date
30-Jun-2017
Publication Date
27-Sep-2017
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
21-Sep-2017
Due Date
26-Nov-2017
Completion Date
28-Sep-2017

RELATIONS

Buy Standard

Standard
SIST EN ISO 6149-4:2017
English language
18 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day

Standards Content (sample)

SLOVENSKI STANDARD
SIST EN ISO 6149-4:2017
01-november-2017
1DGRPHãþD
SIST EN ISO 6149-4:2015

3ULNOMXþNLYIOXLGQLWHKQLNLLQ]DVSORãQRXSRUDER9KRGLLQUDYQL]DNOMXþNL]QDYRML

SR,62LQWHVQLONDPL2GHO0HUHNRQVWUXNFLMDSUHVNXVQHPHWRGHWHU
]DKWHYH]D]XQDQMHLQQRWUDQMHþHSH ,62

Connections for fluid power and general use - Ports and stud ends with ISO 261 metric

threads and O-ring sealing - Part 4: Dimensions, design, test methods and requirements

for external hex and internal hex port plugs (ISO 6149-4:2017)

Raccordements pour transmissions hydrauliques et applications générales - Orifices et

éléments mâles à filetage métrique ISO 261 et joint torique - Partie 4: Dimensions,

conception, méthodes d'essai et exigences des bouchons d'orifice à six pans externes et

à six pans internes (ISO 6149-4:2017)
Ta slovenski standard je istoveten z: EN ISO 6149-4:2017
ICS:
23.100.40 Cevna napeljava in sklopke Piping and couplings
23.100.60 )LOWULWHVQLODLQ Filters, seals and
RQHVQDåHYDQMHWHNRþLQ contamination of fluids
SIST EN ISO 6149-4:2017 en

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 6149-4:2017
---------------------- Page: 2 ----------------------
SIST EN ISO 6149-4:2017
EN ISO 6149-4
EUROPEAN STANDARD
NORME EUROPÉENNE
September 2017
EUROPÄISCHE NORM
ICS 23.100.40 Supersedes EN ISO 6149-4:2014
English Version
Connections for fluid power and general use - Ports and
stud ends with ISO 261 metric threads and O-ring sealing -
Part 4: Dimensions, design, test methods and
requirements for external hex and internal hex port plugs
(ISO 6149-4:2017)
Raccordements pour transmissions hydrauliques et
applications générales - Orifices et éléments mâles à
filetage métrique ISO 261 et joint torique - Partie 4:
Dimensions, conception, méthodes d'essai et exigences
des bouchons d'orifice à six pans externes et à six pans
internes (ISO 6149-4:2017)
This European Standard was approved by CEN on 7 September 2017.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this

European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references

concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN

member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by

translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management

Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,

Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,

Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,

Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels

© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 6149-4:2017 E

worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 6149-4:2017
EN ISO 6149-4:2017 (E)
Contents Page

European foreword ....................................................................................................................................................... 3

---------------------- Page: 4 ----------------------
SIST EN ISO 6149-4:2017
EN ISO 6149-4:2017 (E)
European foreword

This document (EN ISO 6149-4:2017) has been prepared by Technical Committee ISO/TC 131 “Fluid

power systems” in collaboration with Technical Committee ECISS/TC 110 “Steel tubes, and iron and

steel fittings” the secretariat of which is held by UNI.

This European Standard shall be given the status of a national standard, either by publication of an

identical text or by endorsement, at the latest by March 2018 and conflicting national standards shall be

withdrawn at the latest by March 2018.

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. CEN shall not be held responsible for identifying any or all such patent rights.

This document supersedes EN ISO 6149-4:2014.

According to the CEN-CENELEC Internal Regulations, the national standards organizations of the

following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,

Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,

France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,

Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,

Turkey and the United Kingdom.
Endorsement notice

The text of ISO 6149-4:2017 has been approved by CEN as EN ISO 6149-4:2017 without any

modification.
---------------------- Page: 5 ----------------------
SIST EN ISO 6149-4:2017
---------------------- Page: 6 ----------------------
SIST EN ISO 6149-4:2017
INTERNATIONAL ISO
STANDARD 6149-4
Second edition
2017-08
Connections for fluid power and
general use — Ports and stud ends
with ISO 261 metric threads and
O-ring sealing —
Part 4:
Dimensions, design, test methods and
requirements for external hex and
internal hex port plugs
Raccordements pour transmissions hydrauliques et applications
générales — Orifices et éléments mâles à filetage métrique ISO 261 et
joint torique —
Partie 4: Dimensions, conception, méthodes d’essai et exigences des
bouchons d’orifice à six pans externes et à six pans internes
Reference number
ISO 6149-4:2017(E)
ISO 2017
---------------------- Page: 7 ----------------------
SIST EN ISO 6149-4:2017
ISO 6149-4:2017(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2017, Published in Switzerland

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form

or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior

written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of

the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 6149-4:2017
ISO 6149-4:2017(E)
Contents Page

Foreword ........................................................................................................................................................................................................................................iv

Introduction ..................................................................................................................................................................................................................................v

1 Scope ................................................................................................................................................................................................................................. 1

2 Normative references ...................................................................................................................................................................................... 1

3 Terms and definitions ..................................................................................................................................................................................... 2

4 Dimensions ................................................................................................................................................................................................................. 2

4.1 Plug dimensions ..................................................................................................................................................................................... 2

4.2 Hex tolerances ......................................................................................................................................................................................... 2

4.3 Screw threads........................................................................................................................................................................................... 2

5 Requirements .......................................................................................................................................................................................................... 2

5.1 Working pressures and working temperatures .......................................................................................................... 2

5.2 Performance .............................................................................................................................................................................................. 3

6 O-rings ............................................................................................................................................................................................................................. 3

7 Test methods ............................................................................................................................................................................................................. 3

8 Designation of port plugs ............................................................................................................................................................................ 3

9 Identification ............................................................................................................................................................................................................ 3

10 Manufacture .............................................................................................................................................................................................................. 4

10.1 Construction .............................................................................................................................................................................................. 4

10.2 Workmanship ........................................................................................................................................................................................... 4

10.3 Finish ............................................................................................................................................................................................................... 4

11 Procurement information ........................................................................................................................................................................... 4

12 Marking .......................................................................................................................................................................................................................... 4

13 Identification statement (reference to this document) ............................................................................................... 4

Bibliography .............................................................................................................................................................................................................................10

© ISO 2017 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 6149-4:2017
ISO 6149-4:2017(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the

different types of ISO documents should be noted. This document was drafted in accordance with the

editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of

any patent rights identified during the development of the document will be in the Introduction and/or

on the ISO list of patent declarations received (see www .iso .org/ patents).

Any trade name used in this document is information given for the convenience of users and does not

constitute an endorsement.

For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and

expressions related to conformity assessment, as well as information about ISO’s adherence to the

World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following

URL: w w w . i s o .org/ iso/ foreword .html.

This document was prepared by ISO/TC 131, Fluid power systems, SC 4, Connectors and similar products

and components.

This second edition cancels and replaces the first edition (ISO 6149-4:2006), of which it constitutes a

minor revision.

The main change since last version is the addition of a warning statement about the hazards of

intermixing of stud ends with the various port types.
iv © ISO 2017 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 6149-4:2017
ISO 6149-4:2017(E)
Introduction

In fluid power systems, power is transmitted and controlled through a fluid (liquid or gas) under

pressure within an enclosed circuit. In general applications, a fluid can be conveyed under pressure.

Components are connected through their threaded ports by stud ends on fluid conductor connectors to

tubes and pipes or to hose fittings and hoses. Fluid ports are closed by inserting a plug in the port.

© ISO 2017 – All rights reserved v
---------------------- Page: 11 ----------------------
SIST EN ISO 6149-4:2017
---------------------- Page: 12 ----------------------
SIST EN ISO 6149-4:2017
INTERNATIONAL STANDARD ISO 6149-4:2017(E)
Connections for fluid power and general use — Ports
and stud ends with ISO 261 metric threads and O-ring
sealing —
Part 4:
Dimensions, design, test methods and requirements for
external hex and internal hex port plugs
1 Scope

This document specifies dimensions and performance requirements for external hex and internal hex

port plugs for use with ISO 6149-1 ports.

Port plugs in accordance with this document can be used at working pressures up to 63 MPa (630 bar ).

The permissible working pressure depends upon the plug end size, materials, design, working

conditions, application, etc.

Conformance to the dimensional information in this document does not guarantee rated performance.

Each manufacturer is expected to perform testing according to the specification contained in this

document to assure that components comply with the performance ratings.

WARNING — The use of stud ends conforming to this document with ports conforming to the

relevant parts of ISO 1179, ISO 9974 and ISO 11926 could lead to a hazardous situation.

2 Normative references
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.