SIST EN ISO 21531:2009
(Main)Dentistry - Graphical symbols for dental instruments (ISO 21531:2009)
Dentistry - Graphical symbols for dental instruments (ISO 21531:2009)
This International Standard presents a series of graphical symbols for dental instruments. They are set out particularly for this area of dentistry or corresponding specific areas within dentistry. General symbols are taken from relevant ISO, IEC or other international documents. Several new symbols presented by manufacturers or users have been added. Because many dental products are considered in some cases as medical devices and in some cases not as medical devices, in dentistry the restricted usage of the symbols specified in ISO 15223 is considered as not practical. It is the intention of this International Standard to expand the application area of some graphical symbols specified in ISO 15223 to the whole area of dentistry. Therefore these symbols are listed in this International Standard together with their source document.
Zahnheilkunde - Grafische Symbole für Dentalinstrumente (ISO 21531:2009)
Diese Internationale Norm beschreibt eine Reihe von grafischen Symbolen für Dentalinstrumente. Sie wurden speziell für diesen Bereich der Zahnheilkunde oder korrespondierende Bereiche innerhalb der Zahnheilkunde entwickelt. Allgemeine Symbole werden von den relevanten ISO, IEC oder anderen internationalen Dokumenten übernommen. Verschiedene neue Symbole, die von den Herstellern oder Anwendern vorgelegt wurden, wurden mit aufgenommen.
Weil viele Dentalprodukte in manchen Fällen als Medizinprodukte und in manchen Fällen nicht als Medizinprodukte angesehen werden, wird der eingeschränkte Anwendungsbereich von ISO 15223 als nicht praktisch angesehen. Es ist die Absicht dieser Internationalen Norm den Anwendungsbereich einiger grafischer Symbole aus ISO 15223 auf die gesamte Zahnheilkunde zu erweitern. Deshalb werden diese Symbole in dieser Internationalen Norm zusammen mit dem Ursprungsdokument aufgeführt.
ANMERKUNG Zusätzlich zu den Benennungen, die in zwei der drei offiziellen ISO-Sprachfassungen (Englisch, Französisch und Russisch) gegeben werden, enthält diese Internationale Norm äquivalente Benennungen in der deutschen Sprache; diese erscheinen unter der Verantwortung des Mitgliedes für Deutschland (DIN). Nur die Benennungen in den offiziellen ISO-Sprachen dürfen deshalb als ISO-Benennungen angesehen werden.
Art dentaire - Symboles graphiques pour instruments dentaires (ISO 21531:2009)
L'ISO 21531:2009 présente une série de symboles graphiques pour les instruments dentaires. Ils ont été établis spécifiquement pour le domaine de l'art dentaire ou pour des domaines spécifiques correspondants de l'art dentaire. Les symboles généraux sont issus de documents internationaux ISO, CEI ou autres. Plusieurs nouveaux symboles présentés par des fabricants ou des utilisateurs ont été ajoutés.
Zobozdravstvo - Grafični simboli za dentalne instrumente (ISO 21531:2009)
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 21531:2009
01-april-2009
=RER]GUDYVWYR*UDILþQLVLPEROL]DGHQWDOQHLQVWUXPHQWH ,62
Dentistry - Graphical symbols for dental instruments (ISO 21531:2009)
Zahnheilkunde - Grafische Symbole für Dentalinstrumente (ISO 21531:2009)
Art dentaire - Symboles graphiques pour instruments dentaires (ISO 21531:2009)
Ta slovenski standard je istoveten z: EN ISO 21531:2009
ICS:
01.080.20 *UDILþQLVLPEROL]DSRVHEQR Graphical symbols for use on
RSUHPR specific equipment
11.060.25 =RERWHKQLþQLLQVWUXPHQWL Dental instruments
SIST EN ISO 21531:2009 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 21531:2009
---------------------- Page: 2 ----------------------
SIST EN ISO 21531:2009
EUROPEAN STANDARD
EN ISO 21531
NORME EUROPÉENNE
EUROPÄISCHE NORM
February 2009
ICS 11.060.01; 01.080.99
English Version
Dentistry - Graphical symbols for dental instruments (ISO
21531:2009)
Art dentaire - Symboles graphiques pour instruments Zahnheilkunde - Graphische Symbole für
dentaires (ISO 21531:2009) Dentalinstrumente (ISO 21531:2008)
This European Standard was approved by CEN on 21 January 2009.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 21531:2009: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 21531:2009
EN ISO 21531:2009 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 21531:2009
EN ISO 21531:2009 (E)
Foreword
This document (EN ISO 21531:2009) has been prepared by Technical Committee ISO/TC 106 "Dentistry" in
collaboration with Technical Committee CEN/TC 55 "Dentistry", the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by August 2009, and conflicting national standards shall be withdrawn at
the latest by August 2009.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 21531:2009 has been approved by CEN as a EN ISO 21531:2009 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 21531:2009
---------------------- Page: 6 ----------------------
SIST EN ISO 21531:2009
INTERNATIONAL ISO
STANDARD 21531
First edition
2009-02-15
Dentistry — Graphical symbols for dental
instruments
Art dentaire — Symboles graphiques pour instruments dentaires
Reference number
ISO 21531:2009(E)
©
ISO 2009
---------------------- Page: 7 ----------------------
SIST EN ISO 21531:2009
ISO 21531:2009(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2009
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2009 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 21531:2009
ISO 21531:2009(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions. 1
4 Requirements . 2
4.1 General. 2
4.2 Use of graphical symbols . 2
4.3 Size of symbols. 2
4.4 Representation of names of languages and dates. 2
5 Graphical symbols. 3
Bibliography . 13
© ISO 2009 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 21531:2009
ISO 21531:2009(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee has
been established has the right to be represented on that committee. International organizations, governmental
and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 21531 was prepared by Technical Committee ISO/TC 106, Dentistry, Subcommittee SC 4, Dental
instruments.
iv © ISO 2009 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 21531:2009
ISO 21531:2009(E)
Introduction
Graphical symbols are used in many areas of daily life. They give necessary and useful information of many
kinds in a visual way. They are used as signals (warning or alarm signals), for general information, as a
means of control, for the correct application of machines, instruments, etc. and in may other ways of
communication.
Their content of information is very often superior to verbal explanations because their information is visually
acknowledged instantly and is often kept in memory easier and longer than terms or phonetic explanations.
Graphical symbols are internationally understandable without sometimes difficult, possibly misleading and
costly translations.
Each ISO technical committee is responsible for the selection or creation of graphical symbols within its own
field of interest. Graphical symbols may form the main subject of an International Standard, or a single symbol
or several symbols may appear as part of a standard covering wider aspects of the subject to which the
symbol(s) refer(s).
The ISO Technical Management Board has assigned overall responsibility for standardization in the field of
graphical symbols to ISO/TC 145, Graphical symbols, and to ISO/TC 10/SC 10, Technical product
documentation (tpd) symbols.
ISO/TC 210, Quality management and corresponding aspects for medical devices, which is responsible for
the development of ISO 15233, has prepared an international guide to the development and registration of
symbols for use in the labelling of medical devices. This guideline recommends that the proliferation of
graphical symbols without international harmonization is undesirable and contrary to these objectives.
There is a need for simple, internationally accepted graphical symbols labelling that provide general and
specific information to the user in a manner that overcomes the limitations of languages. It is in the best
interests of safety and health of patients, dentists, dental technicians and other persons, to reduce the
confusion inherent in the use of multiple language labelling. Both of these objectives can be met by the use of
standardized symbols agreed by consensus on an international basis.
The task of determining technical requirements to allow the use of specific symbols is best taken up by bodies
expert in the relevant areas. ISO/TC 106/SC 4/WG 5, Number coding system, has taken up this responsibility
by developing this International Standard.
This International Standard has been prepared to reduce the need for multiple translations of words into
national languages, to simplify labelling whereever possible and to prevent separate development of different
symbols to convey the same information.
This International Standard contains a series of symbols (pictograms) for use in dentistry. Their application
should be considered in the literature, for the labelling and packaging of devices used in dentistry, on items of
dental equipment and instruments. Their use is unlimited and a most helpful means of communication within
dentistry.
© ISO 2009 – All rights reserved v
---------------------- Page: 11 ----------------------
SIST EN ISO 21531:2009
---------------------- Page: 12 ----------------------
SIST EN ISO 21531:2009
INTERNATIONAL STANDARD ISO 21531:2009(E)
Dentistry — Graphical symbols for dental instruments
1 Scope
This International Standard presents a series of graphical symbols for dental instruments. They are set out
particularly for this area of dentistry or corresponding specific areas within dentistry. General symbols are
taken from relevant ISO, IEC or other international documents. Several new symbols presented by
manufacturers or users have been added.
Because many dental products are considered in some cases as medical devices and in some cases not as
medical devices, in dentistry the restricted usage of the symbols specified in ISO 15223 is considered as not
practical. It is the intention of this International Standard to expand the application area of some graphical
symbols specified in ISO 15223 to the whole area of dentistry. Therefore these symbols are listed in this
International Standard together with their source document.
NOTE In addition to terms used in two of the three official ISO languages (English, French and Russian), this
International Standard gives the equivalent terms in the German language; these are published under the responsibility of
the member body for Germany (DIN). However, only the terms given in the official languages can be considered as
ISO terms.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.