SIST-TS CEN/TS 18075:2024
(Main)Resilient, textile, laminate and modular mechanical locked floor coverings - Circular economy and sustainability - Recommendations/guidelines for design
Resilient, textile, laminate and modular mechanical locked floor coverings - Circular economy and sustainability - Recommendations/guidelines for design
The aim of this document is to provide general recommendations and guidelines on how to design a product to optimize its reuse and recyclability at the end of its lifetime as well as to take into account sustainable sourcing of materials for all floor covering product groups covered by CEN/TC 134. The overall target is to avoid waste and pollution and to achieve a product fit for the circular economy.
In a linear economy, the focus of product design is on developing new products without considering the recycling or reuse of the raw materials used.
This document provides guidance for processes allowing for (raw) materials used to be returned to the economic cycle based on circular design principles. The focus is on open systems that allow for economically interesting alternatives and are not limited to the principle of closed cycles (product to product).
Specific attention is given to renewable materials, where applicable.
The document is structured along the life cycle of the products, starting with the production phase.
Excluded is packaging, which is not considered part of the product end-of-life stage.
Elastische, textile, Laminat- und modulare mechanisch verriegelnde Bodenbeläge - Kreislaufwirtschaft und Nachhaltigkeit - Empfehlungen/Richtlinien für die Gestaltung
Zweck dieses Dokuments ist die Bereitstellung allgemeiner Empfehlungen und Leitlinien zur Gestaltung eines Produkts mit dem Ziel der Optimierung seiner Wiederverwendung und Recyclingfähigkeit am Ende seiner Lebensdauer sowie der Berücksichtigung nachhaltiger Materialbeschaffung für alle Bodenbelag-Produktgruppen, die von CEN/TC 134 erfasst werden. Das übergeordnete Ziel ist die Vermeidung von Abfall und Verschmutzung sowie das Schaffen eines Produkts, das sich für die Kreislaufwirtschaft eignet.
In einer linearen Wirtschaft liegt der Schwerpunkt der Produktgestaltung auf der Entwicklung neuer Produkte ohne Berücksichtigung von Recycling und Wiederverwendung der verwendeten Rohmaterialien.
Dieses Dokument gibt eine Anleitung für Prozesse, die die Rückführung der verwendeten (Roh )Materialien in den Wirtschaftskreislauf auf Grundlage der Grundsätze für kreislauforientierte Gestaltung ermöglichen. Der Schwerpunkt liegt auf offenen Systemen, die wirtschaftlich interessante Alternativen ermöglichen und nicht auf den Grundsatz geschlossener Kreisläufe (Produkt zu Produkt) beschränkt sind.
Besondere Aufmerksamkeit gilt erneuerbaren Materialien, soweit anwendbar.
Das Dokument ist entsprechend dem Lebenszyklus der Produkte gegliedert, beginnend mit der Produktionsphase.
Ausgenommen ist das Verpacken, das nicht als Teil des Endes der Produktlebensdauer betrachtet wird.
Netekstilne, tekstilne, laminirane in modularne mehansko spojene talne obloge - Krožno gospodarstvo in trajnostnost - Priporočila/smernice za načrtovanje
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2024
Netekstilne, tekstilne, laminirane in modularne mehansko spojene talne obloge -
Krožno gospodarstvo in trajnostnost - Priporočila/smernice za načrtovanje
Resilient, textile, laminate and modular mechanical locked floor coverings - Circular
economy and sustainability - Recommendations/guidelines for design
Elastische, textile, Laminat- und modulare mechanisch verriegelnde Bodenbeläge -
Kreislaufwirtschaft und Nachhaltigkeit - Empfehlungen/Richtlinien für die Gestaltung
Ta slovenski standard je istoveten z: CEN/TS 18075:2024
ICS:
13.020.20 Okoljska ekonomija. Environmental economics.
Trajnostnost Sustainability
97.150 Talne obloge Floor coverings
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
CEN/TS 18075
TECHNICAL SPECIFICATION
SPÉCIFICATION TECHNIQUE
October 2024
TECHNISCHE SPEZIFIKATION
ICS 13.020.20; 97.150
English Version
Resilient, textile, laminate and modular mechanical locked
floor coverings - Circular economy and sustainability -
Recommendations/guidelines for design
Elastische, textile, Laminat- und modulare mechanisch
verriegelnde Bodenbeläge - Kreislaufwirtschaft und
Nachhaltigkeit - Empfehlungen/Richtlinien für die
Gestaltung
This Technical Specification (CEN/TS) was approved by CEN on 12 August 2024 for provisional application.
The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to
submit their comments, particularly on the question whether the CEN/TS can be converted into a European Standard.
CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS
available promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in
parallel to the CEN/TS) until the final decision about the possible conversion of the CEN/TS into an EN is reached.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TS 18075:2024 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Design throughout the different steps in a product’s lifetime . 5
4.1 Overview . 5
4.2 Production phase - Step 1: Define the business model for the flooring . 6
4.3 Production phase - Step 2: Define the product specifications . 7
4.4 Production phase - Step 3: Define the manufacturing process . 9
4.5 Use phase - Step 4: Define the installation method . 9
4.6 Use phase - Step 5: Maintenance . 11
4.7 Use phase - Step 6: Refurbishment/repair . 12
4.8 End-of-use phase - Step 7: Dismantling and further processing for reuse . 13
4.9 End-of-use phase - Step 8: Reuse . 14
4.10 End-of-use phase - Step 9: End-of-life (EOL). 15
Bibliography . 17
European foreword
This document (CEN/TS 18075:2024) has been prepared by Technical Committee CEN/TC 134
“Resilient, textile, laminate and modular mechanical locked floor coverings”, the secretariat of which is
held by NBN.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a standardization request addressed to CEN by the European
Commission (M/584). The Standing Committee of the EFTA States subsequently approves these requests
for its Member States.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN/CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to announce this Technical Specification: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Introduction
The European Commission adopted a European strategy for plastics in January 2018 [1]. It is part of the
European Circular Economy Action Plan [2] and builds on existing measures to reduce plastic waste.
The plastics strategy is a key element of Europe’s transition towards a carbon neutral and circular
economy. It will contribute to reaching the 2030 Sustainable Development Goals, the Paris Climate
Agreement objectives and the EU’s industrial policy objectives.
In 2022 the Commission Implementing Decision on a standardization request to the European Committee
for Standardization and the European Committee for Electrotechnical Standardization as regards plastics
recycling and recycled plastics in support of the European Strategy for Plastics in a Circular Economy
(M/584) [3] was approved, which forms the basis for this document.
In addition to providing an answer to M/584 this document addresses recommendations and guidelines
for design for circular economy and sustainability for resilient, textile, laminate and modular mechanical
locked floor coverings. It highlights the key elements of the life cycle that need to be considered when
designing a product for circularity.
This document is intended for (non-exhaustive list in alphabetical order):
— contractors/installers;
— customers, including end users;
— designers;
— developers;
— facility managers;
— manufacturers;
— retailors (distributors).
This document addresses the possibilities for returning (raw) materials used to the economic cycle based
on circular design principles. The focus is on open systems that allow for economically interesting
alternatives and not limited to the principle of closed cycles (product to product). Recycling of plastics is
one of the methodologies addressed in this document.
This document also highlights the possibilities for cleaning and renewing processes of floor coverings
during their whole lifetime, with the aim to prolong the lifetime of the floor coverings. This allows for
maintaining a longer sustainable perspective and for lowering the impact on the economic cycle of floor
coverings.
1 Scope
The aim of this document is to provide general recommendations and guidelines on how to design a
product to optimize its reuse and recyclability at the end of its lifetime as well as to take into account
sustainable sourcing of materials for all floor covering product groups covered by CEN/TC 134. The
overall target is to avoid waste and pollution and to achieve a product fit for the circular economy.
In a linear economy, the focus of product design is on developing new products without considering the
recycling or reuse of the raw materials used.
This document provides guidance for processes allowing for (raw) materials used to be returned to the
economic cycle based on circular design principles. The focus is on open systems that allow for
economically interesting alternatives and are not limited to the principle of closed cycles (product to
product).
Specific attention is given to renewable materials, where applicable.
The document is structured along the life cycle of the products, starting with the production phase.
Excluded is packaging, which is not considered part of the product end-of-life stage.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 17861:2023, Resilient, textile, laminate and modular mechanical locked floor coverings — Circular
Economy — Terms and definitions
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 17861 apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https://www.iso.org/obp
— IEC Electropedia: available at https://www.electropedia.org/
4 Design throughout the different steps in a product’s lifetime
4.1 Overview
The document follows the following steps in a product’s lifetime (see Figure 1):
1. Production phase
Step 1: Define the business model for the flooring (4.2)
Step 2: Define the product specifications (4.3)
Step 3: Define the manufacturing process (4.4)
2. Use phase
Step 4: Define the installation method (4.5)
Step 5: Maintenance (4.6)
Step 6: Refurbishment/repair (4.7)
3. End-of-use phase
Step 7: Dismantling and further processing for reuse (4.8)
Step 8: Reuse (4.9)
Step 9: End-of-life (EOL) (4.10)
For each step a flow chart or checklist guides the reader through the decision tree for defining the
relevant parameters. The first block of a flow chart indicates the name of the current step, the final block
indicates the next step.
Figure 1 — Schematic diagram showing the various material flows for floor coverings in a
circular economy (EN 17861:2023)
NOTE For preparing environmental product declarations the reader is referred to EN 16810:2017 [4].
4.2 Production phase - Step 1: Define the business model for the flooring
The term “business model” in this context focusses on the intended use and/or ownership of the floor
covering in the long term.
The aim is to develop business models which maximize sustainability and participation in the circular
economy. For this it is necessary to take into account the following:
— sales channel;
— market segment;
— take back program;
— envisioned end user (public, private);
— recycling option;
— option to extend the use phase.
The most relevant elements to consider when developing business models for floor covering are
summarized in this check list:
1. Is a tender available?
2. If yes, the requirements of the tender shall be followed (check if the tender is complete and that it
contains below considerations 4 to 7).
3. If no, then the following considerations shall be taken into account:
4. What is the intended use?
5. Which installation method is the most suitable/ is intended to be used?
6. What additional requirements arise from the given build environment?
7. Are there special considerations for product transport and handling/ can these be optimized?
NOTE This check list (items 4 to 7) can also be followed when preparing a tender.
The product specifications will then need to be determined accordingly (see next step).
4.3 Production phase - Step 2: Define the product specifications
Figure 2 provides guidance for the development of the product specifications.
Product specifications enable the assessment of the product with regards to the use phase a well as all
other stages of its life cycle, by means of measurable facts.
It is recommended to optimize product specification towards efficient material use and minimal
environmental impact, taking into account extending the product lifetime by maintenance, refurbishment
or reuse, and considering end of life options such as recycling. The following points are important to be
considered:
1) HSE (Health, safety and environmental) aspects of materials and substances according to the latest
available knowledge regarding listed substances and substances under investigation (e.g. REACH
legislation [5]);
2) environmental impact of the product design, based on e.g. LCA (Life Cycle Assessment) data. This
incl
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.