SIST EN 303 406 V1.1.1:2017
(Main)Short Range Devices (SRD) - Social Alarms Equipment operating in the frequency range 25 MHz to 1 000 MHz - Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU
Short Range Devices (SRD) - Social Alarms Equipment operating in the frequency range 25 MHz to 1 000 MHz - Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU
The present document specifies technical characteristics and methods of measurements for social alarm systems
operating on a range of frequencies that may be shared with other equipment types.
Social alarms are defined in Commission Decision 2013/752/EU [i.3] as:
"Social alarm devices" are radio communications systems that allow reliable communication for a person in distress in
a confined area to initiate a call for assistance. Typical uses of social alarm are to assist elderly or disabled people.
Naprave kratkega dosega (SRD) - Oprema za socialne alarme, ki deluje v frekvenčnem območju od 25 MHz do 1000 MHz - Harmonizirani standard, ki zajema bistvene zahteve člena 3.2 direktive 2014/53/EU
Ta dokument določa tehnične lastnosti in merilne metode za sisteme socialnih alarmov, ki delujejo prek različnih frekvenc, ki jih lahko souporablja oprema druge vrste.
Socialni alarmi so v sklepu Komisije 2013/752/EU [i.3] opredeljeni kot:
»Naprave za socialno alarmiranje« so zanesljivi radiokomunikacijski sistemi, ki osebi v stiski omogočajo, da v zaprtem prostoru sproži klic na pomoč. Socialni alarm se običajno uporablja za pomoč starejšim ali invalidnim osebam.
General Information
Buy Standard
Standards Content (Sample)
ETSI EN 303 406 V1.1.1 (2017-02)
HARMONISED EUROPEAN STANDARD
Short Range Devices (SRD);
Social Alarms Equipment operating
in the frequency range 25 MHz to 1 000 MHz;
Harmonised Standard covering the essential requirements
of article 3.2 of Directive 2014/53/EU
---------------------- Page: 1 ----------------------
2 ETSI EN 303 406 V1.1.1 (2017-02)
Reference
DEN/ERM-TG28-529
Keywords
alarm, harmonised standard, SRD
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2017.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 303 406 V1.1.1 (2017-02)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 6
Introduction . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 8
3 Definitions, symbols and abbreviations . 9
3.1 Definitions . 9
3.2 Symbols . 9
3.3 Abbreviations . 10
4 Technical requirements specifications . 10
4.1 Environmental profile . 10
4.2 Technical requirements for transmit mode . 10
4.2.1 Applicability . 10
4.2.2 Operating Frequency and Channel . 10
4.2.2.1 Description . 10
4.2.2.2 Limits . 10
4.2.2.3 Conformance . 10
4.2.3 Effective Radiated Power . 10
4.2.3.1 Description . 10
4.2.3.2 Limits . 11
4.2.3.3 Conformance . 11
4.2.4 Duty Cycle . 11
4.2.4.1 Description and Applicability . 11
4.2.4.2 Limits . 11
4.2.4.3 Conformance . 11
4.2.5 Short term behaviour . 11
4.2.5.1 Description and applicability . 11
4.2.5.2 Limits . 11
4.2.5.3 Conformance . 12
4.2.6 Adjacent Channel Power for OCW ≤ 25 kHz . 12
4.2.6.1 Description and Applicability . 12
4.2.6.2 Limits . 12
4.2.6.3 Conformance . 12
4.2.7 Occupied Bandwidth. 12
4.2.7.1 Description and Applicability . 12
4.2.7.2 Limits . 12
4.2.7.3 Conformance . 12
4.2.8 Tx Out Of Band Emissions . 13
4.2.8.1 Description and Applicability . 13
4.2.8.2 Limits . 13
4.2.8.3 Conformance . 13
4.2.9 Transmitter Frequency Error. 13
4.2.9.1 Description and Applicability . 13
4.2.9.2 Limits . 13
4.2.9.3 Conformance . 13
4.2.10 Transmitter Transient Power. 13
4.2.10.1 Description . 13
4.2.10.2 Limits . 13
4.2.10.3 Conformance . 14
4.2.11 Tx Behaviour under Low Voltage Conditions . 14
4.2.11.1 Description and Applicability . 14
ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 303 406 V1.1.1 (2017-02)
4.2.11.2 Limits . 14
4.2.11.3 Conformance . 14
4.3 Technical requirements for all EUT . 14
4.3.1 Applicability . 14
4.3.2 Spurious Emissions . 14
4.3.2.1 Description . 14
4.3.2.2 Limits . 14
4.3.2.3 Conformance . 14
4.4 Receiver Parameters . 14
4.4.1 Applicability . 14
4.4.2 Blocking . 15
4.4.2.1 Description . 15
4.4.2.2 Limits . 15
4.4.2.3 Conformance . 15
5 Technical Requirements for Uni-Directional Communication . 15
5.1 Mode A Applicability and Conformance Requirements . 15
5.2 Communication method . 15
5.3 Transmitter Parameters . 15
5.4 Receiver Parameters . 15
5.4.1 Applicability . 15
5.4.2 Adjacent Channel Selectivity . 15
5.4.2.1 Description . 15
5.4.2.2 Limits . 16
5.4.3 Blocking . 16
5.4.3.1 Description . 16
5.4.3.2 Limits . 16
5.4.3.3 Conformance . 16
5.4.4 Adjacent Channel Saturation . 16
5.4.4.1 Description . 16
5.4.4.2 Limits . 16
5.4.4.3 Conformance . 16
5.4.5 Spurious Response Rejection . 16
5.4.5.1 Description . 16
5.4.5.2 Limits . 16
5.4.5.3 Conformance . 16
5.4.6 Behaviour at high wanted signal level . 17
5.4.6.1 Description . 17
5.4.6.2 Limits . 17
5.4.6.3 Conformance . 17
6 Bi-Directional Communication with Frequency Agility . 17
6.1 Mode BN Applicability and Conformance Requirements . 17
6.2 Bi-directional Communication and Frequency Agility . 17
6.2.1 Applicability . 17
6.2.2 Acknowledgement . 17
6.2.2.1 Description . 17
6.2.2.2 Limits . 17
6.2.2.3 Conformance . 17
6.2.3 Ability to change communication frequency . 18
6.2.3.1 Description . 18
6.2.3.2 Limits . 18
6.2.3.3 Conformance . 18
6.3 Transmitter Parameters . 18
6.4 Receiver Parameters . 18
6.4.1 Applicability . 18
6.4.2 Adjacent Channel Selectivity . 18
6.4.2.1 Description . 18
6.4.2.2 Limits . 18
6.4.2.3 Conformance . 18
6.4.3 Blocking . 18
6.4.3.1 Description . 18
ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 303 406 V1.1.1 (2017-02)
6.4.3.2 Limits . 19
6.4.3.3 Conformance . 19
6.4.4 Adjacent Channel Saturation . 19
6.4.4.1 Description . 19
6.4.4.2 Limits . 19
6.4.4.3 Conformance . 19
6.4.5 Spurious Response Rejection . 19
6.4.5.1 Description . 19
6.4.5.2 Limits . 19
6.4.5.3 Conformance . 19
6.4.6 Behaviour at high wanted signal level . 20
6.4.6.1 Description . 20
6.4.6.2 Limits . 20
6.4.6.3 Conformance . 20
7 Testing for compliance with technical requirements . 20
7.1 General . 20
7.2 Presentation of equipment for testing purposes . 20
7.3 Wanted performance criteria . 21
7.3.1 Receiver response . 21
7.4 Radio test suites - Transceivers . 21
7.4.1 Frequency Agility . 21
7.4.1.1 Description . 21
7.4.1.2 Test Conditions . 21
7.4.1.3 Method of measurement . 21
7.4.1.4 Measurement procedure . 21
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 23
Annex B (normative): Operating bands and technical parameters . 25
Annex C (informative): Selection of technical parameters . 27
C.1 Introduction . 27
C.2 Receiver sensitivity . 27
C.3 Other receiver parameters . 27
C.4 Transmitter short term behaviour . 27
C.5 Listen before talk . 28
Annex D (informative): Bibliography . 29
History . 30
ETSI
---------------------- Page: 5 ----------------------
6 ETSI EN 303 406 V1.1.1 (2017-02)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM).
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.10] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.2].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive and associated
EFTA regulations.
National transposition dates
Date of adoption of this EN: 10 February 2017
Date of latest announcement of this EN (doa): 31 May 2017
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 30 November 2017
Date of withdrawal of any conflicting National Standard (dow): 30 November 2018
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 6 ----------------------
7 ETSI EN 303 406 V1.1.1 (2017-02)
Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio equipment within the scope of the Radio Equipment Directive (RED) [i.2].
It is recognized that the radio communications link alone does not determine the overall operation of a system, but that a
functioning radio communications link is an essential foundation upon which a system may be built.
The present document sets out various means and features by which the performa
...
SLOVENSKI STANDARD
SIST EN 303 406 V1.1.1:2017
01-maj-2017
1DSUDYHNUDWNHJDGRVHJD 65' 2SUHPD]DVRFLDOQHDODUPHNLGHOXMHY
IUHNYHQþQHPREPRþMXRG0+]GR0+]+DUPRQL]LUDQLVWDQGDUGNL]DMHPD
ELVWYHQH]DKWHYHþOHQDGLUHNWLYH(8
Short Range Devices (SRD) - Social Alarms Equipment operating in the frequency range
25 MHz to 1 000 MHz - Harmonised Standard covering the essential requirements of
article 3.2 of the Directive 2014/53/EU
Ta slovenski standard je istoveten z: ETSI EN 303 406 V1.1.1 (2017-02)
ICS:
13.320 Alarmni in opozorilni sistemi Alarm and warning systems
33.060.99 Druga oprema za radijske Other equipment for
komunikacije radiocommunications
SIST EN 303 406 V1.1.1:2017 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 303 406 V1.1.1:2017
---------------------- Page: 2 ----------------------
SIST EN 303 406 V1.1.1:2017
ETSI EN 303 406 V1.1.1 (2017-02)
HARMONISED EUROPEAN STANDARD
Short Range Devices (SRD);
Social Alarms Equipment operating
in the frequency range 25 MHz to 1 000 MHz;
Harmonised Standard covering the essential requirements
of article 3.2 of Directive 2014/53/EU
---------------------- Page: 3 ----------------------
SIST EN 303 406 V1.1.1:2017
2 ETSI EN 303 406 V1.1.1 (2017-02)
Reference
DEN/ERM-TG28-529
Keywords
alarm, harmonised standard, SRD
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2017.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 4 ----------------------
SIST EN 303 406 V1.1.1:2017
3 ETSI EN 303 406 V1.1.1 (2017-02)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 6
Introduction . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 8
3 Definitions, symbols and abbreviations . 9
3.1 Definitions . 9
3.2 Symbols . 9
3.3 Abbreviations . 10
4 Technical requirements specifications . 10
4.1 Environmental profile . 10
4.2 Technical requirements for transmit mode . 10
4.2.1 Applicability . 10
4.2.2 Operating Frequency and Channel . 10
4.2.2.1 Description . 10
4.2.2.2 Limits . 10
4.2.2.3 Conformance . 10
4.2.3 Effective Radiated Power . 10
4.2.3.1 Description . 10
4.2.3.2 Limits . 11
4.2.3.3 Conformance . 11
4.2.4 Duty Cycle . 11
4.2.4.1 Description and Applicability . 11
4.2.4.2 Limits . 11
4.2.4.3 Conformance . 11
4.2.5 Short term behaviour . 11
4.2.5.1 Description and applicability . 11
4.2.5.2 Limits . 11
4.2.5.3 Conformance . 12
4.2.6 Adjacent Channel Power for OCW ≤ 25 kHz . 12
4.2.6.1 Description and Applicability . 12
4.2.6.2 Limits . 12
4.2.6.3 Conformance . 12
4.2.7 Occupied Bandwidth. 12
4.2.7.1 Description and Applicability . 12
4.2.7.2 Limits . 12
4.2.7.3 Conformance . 12
4.2.8 Tx Out Of Band Emissions . 13
4.2.8.1 Description and Applicability . 13
4.2.8.2 Limits . 13
4.2.8.3 Conformance . 13
4.2.9 Transmitter Frequency Error. 13
4.2.9.1 Description and Applicability . 13
4.2.9.2 Limits . 13
4.2.9.3 Conformance . 13
4.2.10 Transmitter Transient Power. 13
4.2.10.1 Description . 13
4.2.10.2 Limits . 13
4.2.10.3 Conformance . 14
4.2.11 Tx Behaviour under Low Voltage Conditions . 14
4.2.11.1 Description and Applicability . 14
ETSI
---------------------- Page: 5 ----------------------
SIST EN 303 406 V1.1.1:2017
4 ETSI EN 303 406 V1.1.1 (2017-02)
4.2.11.2 Limits . 14
4.2.11.3 Conformance . 14
4.3 Technical requirements for all EUT . 14
4.3.1 Applicability . 14
4.3.2 Spurious Emissions . 14
4.3.2.1 Description . 14
4.3.2.2 Limits . 14
4.3.2.3 Conformance . 14
4.4 Receiver Parameters . 14
4.4.1 Applicability . 14
4.4.2 Blocking . 15
4.4.2.1 Description . 15
4.4.2.2 Limits . 15
4.4.2.3 Conformance . 15
5 Technical Requirements for Uni-Directional Communication . 15
5.1 Mode A Applicability and Conformance Requirements . 15
5.2 Communication method . 15
5.3 Transmitter Parameters . 15
5.4 Receiver Parameters . 15
5.4.1 Applicability . 15
5.4.2 Adjacent Channel Selectivity . 15
5.4.2.1 Description . 15
5.4.2.2 Limits . 16
5.4.3 Blocking . 16
5.4.3.1 Description . 16
5.4.3.2 Limits . 16
5.4.3.3 Conformance . 16
5.4.4 Adjacent Channel Saturation . 16
5.4.4.1 Description . 16
5.4.4.2 Limits . 16
5.4.4.3 Conformance . 16
5.4.5 Spurious Response Rejection . 16
5.4.5.1 Description . 16
5.4.5.2 Limits . 16
5.4.5.3 Conformance . 16
5.4.6 Behaviour at high wanted signal level . 17
5.4.6.1 Description . 17
5.4.6.2 Limits . 17
5.4.6.3 Conformance . 17
6 Bi-Directional Communication with Frequency Agility . 17
6.1 Mode BN Applicability and Conformance Requirements . 17
6.2 Bi-directional Communication and Frequency Agility . 17
6.2.1 Applicability . 17
6.2.2 Acknowledgement . 17
6.2.2.1 Description . 17
6.2.2.2 Limits . 17
6.2.2.3 Conformance . 17
6.2.3 Ability to change communication frequency . 18
6.2.3.1 Description . 18
6.2.3.2 Limits . 18
6.2.3.3 Conformance . 18
6.3 Transmitter Parameters . 18
6.4 Receiver Parameters . 18
6.4.1 Applicability . 18
6.4.2 Adjacent Channel Selectivity . 18
6.4.2.1 Description . 18
6.4.2.2 Limits . 18
6.4.2.3 Conformance . 18
6.4.3 Blocking . 18
6.4.3.1 Description . 18
ETSI
---------------------- Page: 6 ----------------------
SIST EN 303 406 V1.1.1:2017
5 ETSI EN 303 406 V1.1.1 (2017-02)
6.4.3.2 Limits . 19
6.4.3.3 Conformance . 19
6.4.4 Adjacent Channel Saturation . 19
6.4.4.1 Description . 19
6.4.4.2 Limits . 19
6.4.4.3 Conformance . 19
6.4.5 Spurious Response Rejection . 19
6.4.5.1 Description . 19
6.4.5.2 Limits . 19
6.4.5.3 Conformance . 19
6.4.6 Behaviour at high wanted signal level . 20
6.4.6.1 Description . 20
6.4.6.2 Limits . 20
6.4.6.3 Conformance . 20
7 Testing for compliance with technical requirements . 20
7.1 General . 20
7.2 Presentation of equipment for testing purposes . 20
7.3 Wanted performance criteria . 21
7.3.1 Receiver response . 21
7.4 Radio test suites - Transceivers . 21
7.4.1 Frequency Agility . 21
7.4.1.1 Description . 21
7.4.1.2 Test Conditions . 21
7.4.1.3 Method of measurement . 21
7.4.1.4 Measurement procedure . 21
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 23
Annex B (normative): Operating bands and technical parameters . 25
Annex C (informative): Selection of technical parameters . 27
C.1 Introduction . 27
C.2 Receiver sensitivity . 27
C.3 Other receiver parameters . 27
C.4 Transmitter short term behaviour . 27
C.5 Listen before talk . 28
Annex D (informative): Bibliography . 29
History . 30
ETSI
---------------------- Page: 7 ----------------------
SIST EN 303 406 V1.1.1:2017
6 ETSI EN 303 406 V1.1.1 (2017-02)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM).
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.10] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.2].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive and associated
EFTA regulations.
National transposition dates
Date of adoption of this EN: 10 February 2017
Date of latest announcement of this EN (doa): 31 May 2017
Date of latest publicatio
...
Final draft ETSI EN 303 406 V1.1.1 (2016-12)
HARMONISED EUROPEAN STANDARD
Short Range Devices (SRD);
Social Alarms Equipment operating
in the frequency range 25 MHz to 1 000 MHz;
Harmonised Standard covering the essential requirements
of article 3.2 of Directive 2014/53/EU
---------------------- Page: 1 ----------------------
2 Final draft ETSI EN 303 406 V1.1.1 (2016-12)
Reference
DEN/ERM-TG28-529
Keywords
alarm, harmonised standard, SRD
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2016.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Final draft ETSI EN 303 406 V1.1.1 (2016-12)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 6
Introduction . 6
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 8
3 Definitions, symbols and abbreviations . 9
3.1 Definitions . 9
3.2 Symbols . 9
3.3 Abbreviations . 10
4 Technical requirements specifications . 10
4.1 Environmental profile . 10
4.2 Technical requirements for transmit mode . 10
4.2.1 Applicability . 10
4.2.2 Operating Frequency and Channel . 10
4.2.2.1 Description . 10
4.2.2.2 Limits . 10
4.2.2.3 Conformance . 10
4.2.3 Effective Radiated Power . 10
4.2.3.1 Description . 10
4.2.3.2 Limits . 11
4.2.3.3 Conformance . 11
4.2.4 Duty Cycle . 11
4.2.4.1 Description and Applicability . 11
4.2.4.2 Limits . 11
4.2.4.3 Conformance . 11
4.2.5 Short term behaviour . 11
4.2.5.1 Description and applicability . 11
4.2.5.2 Limits . 12
4.2.5.3 Conformance . 12
4.2.6 Adjacent Channel Power for OCW ≤ 25 kHz . 12
4.2.6.1 Description and Applicability . 12
4.2.6.2 Limits . 12
4.2.6.3 Conformance . 12
4.2.7 Occupied Bandwidth. 12
4.2.7.1 Description and Applicability . 12
4.2.7.2 Limits . 12
4.2.7.3 Conformance . 13
4.2.8 Tx Out Of Band Emissions . 13
4.2.8.1 Description and Applicability . 13
4.2.8.2 Limits . 13
4.2.8.3 Conformance . 13
4.2.9 Transmitter Frequency Error. 13
4.2.9.1 Description and Applicability . 13
4.2.9.2 Limits . 13
4.2.9.3 Conformance . 13
4.2.10 Transmitter Transient Power. 14
4.2.10.1 Description . 14
4.2.10.2 Limits . 14
4.2.10.3 Conformance . 14
4.2.11 Tx Behaviour under Low Voltage Conditions . 14
4.2.11.1 Description and Applicability . 14
ETSI
---------------------- Page: 3 ----------------------
4 Final draft ETSI EN 303 406 V1.1.1 (2016-12)
4.2.11.2 Limits . 14
4.2.11.3 Conformance . 14
4.3 Technical requirements for all EUT . 14
4.3.1 Applicability . 14
4.3.2 Spurious Emissions . 14
4.3.2.1 Description . 14
4.3.2.2 Limits . 14
4.3.2.3 Conformance . 15
4.4 Receiver Parameters . 15
4.4.1 Applicability . 15
4.4.2 Blocking . 15
4.4.2.1 Description . 15
4.4.2.2 Limits . 15
4.4.2.3 Conformance . 15
5 Technical Requirements for Uni-Directional Communication . 15
5.1 Mode A Applicability and Conformance Requirements . 15
5.2 Communication method . 15
5.3 Transmitter Parameters . 15
5.4 Receiver Parameters . 16
5.4.1 Applicability . 16
5.4.2 Adjacent Channel Selectivity . 16
5.4.2.1 Description . 16
5.4.2.2 Limits . 16
5.4.3 Blocking . 16
5.4.3.1 Description . 16
5.4.3.2 Limits . 16
5.4.3.3 Conformance . 16
5.4.4 Adjacent Channel Saturation . 16
5.4.4.1 Description . 16
5.4.4.2 Limits . 16
5.4.4.3 Conformance . 16
5.4.5 Spurious Response Rejection . 17
5.4.5.1 Description . 17
5.4.5.2 Limits . 17
5.4.5.3 Conformance . 17
5.4.6 Behaviour at high wanted signal level . 17
5.4.6.1 Description . 17
5.4.6.2 Limits . 17
5.4.6.3 Conformance . 17
6 Bi-Directional Communication with Frequency Agility . 17
6.1 Mode BN Applicability and Conformance Requirements . 17
6.2 Bi-directional Communication and Frequency Agility . 17
6.2.1 Applicability . 17
6.2.2 Acknowledgement . 18
6.2.2.1 Description . 18
6.2.2.2 Limits . 18
6.2.2.3 Conformance . 18
6.2.3 Ability to change communication frequency . 18
6.2.3.1 Description . 18
6.2.3.2 Limits . 18
6.2.3.3 Conformance . 18
6.3 Transmitter Parameters . 18
6.4 Receiver Parameters . 18
6.4.1 Applicability . 18
6.4.2 Adjacent Channel Selectivity . 18
6.4.2.1 Description . 18
6.4.2.2 Limits . 19
6.4.2.3 Conformance . 19
6.4.3 Blocking . 19
6.4.3.1 Description . 19
ETSI
---------------------- Page: 4 ----------------------
5 Final draft ETSI EN 303 406 V1.1.1 (2016-12)
6.4.3.2 Limits . 19
6.4.3.3 Conformance . 19
6.4.4 Adjacent Channel Saturation . 19
6.4.4.1 Description . 19
6.4.4.2 Limits . 19
6.4.4.3 Conformance . 19
6.4.5 Spurious Response Rejection . 20
6.4.5.1 Description . 20
6.4.5.2 Limits . 20
6.4.5.3 Conformance . 20
6.4.6 Behaviour at high wanted signal level . 20
6.4.6.1 Description . 20
6.4.6.2 Limits . 20
6.4.6.3 Conformance . 20
7 Testing for compliance with technical requirements . 20
7.1 General . 20
7.2 Presentation of equipment for testing purposes . 20
7.3 Wanted performance criteria . 21
7.3.1 Receiver response . 21
7.4 Radio test suites - Transceivers . 21
7.4.1 Frequency Agility . 21
7.4.1.1 Description . 21
7.4.1.2 Test Conditions . 21
7.4.1.3 Method of measurement . 22
7.4.1.4 Measurement procedure . 22
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 23
Annex B (normative): Operating bands and technical parameters . 25
Annex C (informative): Selection of technical parameters . 27
C.1 Introduction . 27
C.2 Receiver sensitivity . 27
C.3 Other receiver parameters . 27
C.4 Transmitter short term behaviour . 27
C.5 Listen before talk . 28
Annex D (informative): Bibliography . 29
History . 30
ETSI
---------------------- Page: 5 ----------------------
6 Final draft ETSI EN 303 406 V1.1.1 (2016-12)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This final draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee
Electromagnetic compatibility and Radio spectrum Matters (ERM), and is now submitted for the Vote phase of the
ETSI standards EN Approval Procedure.
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.10] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.2].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive and associated
EFTA regulations.
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio equipment within the scope of the Radio Equipment Directive (RED) [i.2].
It is recognized that the radio communications link alone does not determine the overall operation of a system, but that a
functioning radio communications link is an essential foundation upon which a system may be built.
ETSI
---------------
...
Draft ETSI EN 303 406 V1.1.0 (2016-05)
HARMONISED EUROPEAN STANDARD
Short Range Devices (SRD);
Social Alarms Equipment operating
in the frequency range 25 MHz to 1 000 MHz;
Harmonised Standard covering the essential requirements
of article 3.2 of the Directive 2014/53/EU
---------------------- Page: 1 ----------------------
2 Draft ETSI EN 303 406 V1.1.0 (2016-05)
Reference
DEN/ERM-TG28-529
Keywords
alarm, harmonised standard, SRD
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2016.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Draft ETSI EN 303 406 V1.1.0 (2016-05)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 6
Introduction . 6
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 8
3 Definitions, symbols and abbreviations . 9
3.1 Definitions . 9
3.2 Symbols . 9
3.3 Abbreviations . 9
4 Technical requirements specifications . 10
4.1 Environmental profile . 10
4.2 Technical requirements for transmit mode . 10
4.2.1 Applicability . 10
4.2.2 Operating Frequency and Channel . 10
4.2.2.1 Description . 10
4.2.2.2 Limits . 10
4.2.2.3 Conformance . 10
4.2.3 Effective Radiated Power . 10
4.2.3.1 Description . 10
4.2.3.2 Limits . 10
4.2.3.3 Conformance . 10
4.2.4 Duty Cycle . 11
4.2.4.1 Description and Applicability . 11
4.2.4.2 Limits . 11
4.2.4.3 Conformance . 11
4.2.5 Short term behaviour . 11
4.2.5.1 Description and applicability . 11
4.2.5.2 Limits . 11
4.2.5.3 Conformance . 12
4.2.6 Adjacent Channel Power for OCW ≤ 25 kHz . 12
4.2.6.1 Description and Applicability . 12
4.2.6.2 Limits . 12
4.2.6.3 Conformance . 12
4.2.7 Occupied Bandwidth. 12
4.2.7.1 Description and Applicability . 12
4.2.7.2 Limits . 12
4.2.7.3 Conformance . 12
4.2.8 Tx Out Of Band Emissions . 12
4.2.8.1 Description and Applicability . 12
4.2.8.2 Limits . 12
4.2.8.3 Conformance . 13
4.2.9 Transmitter Frequency Error. 13
4.2.9.1 Description and Applicability . 13
4.2.9.2 Limits . 13
4.2.9.3 Conformance . 13
4.2.10 Transmitter Transient Power. 13
4.2.10.1 Description . 13
4.2.10.2 Limits . 13
4.2.10.3 Conformance . 13
4.2.12 Tx Behaviour under Low Voltage Conditions . 13
4.2.12.1 Description and Applicability . 13
ETSI
---------------------- Page: 3 ----------------------
4 Draft ETSI EN 303 406 V1.1.0 (2016-05)
4.2.12.2 Limits . 13
4.2.12.3 Conformance . 13
4.3 Technical requirements for all EUT . 14
4.3.1 Applicability . 14
4.3.2 Spurious Emissions . 14
4.3.2.1 Description . 14
4.3.2.2 Limits . 14
4.3.2.3 Conformance . 14
4.4 Receiver Parameters . 14
4.4.1 Applicability . 14
4.4.2 Blocking . 14
4.4.2.1 Description . 14
4.4.2.2 Limits . 14
4.4.2.3 Conformance . 14
5 Technical Requirements for Uni-Directional Communication . 14
5.1 Mode A Applicability and Conformance Requirements . 14
5.2 Communication method . 15
5.3 Transmitter Parameters . 15
5.4 Receiver Parameters . 15
5.4.1 Applicability . 15
5.4.2 Adjacent Channel Selectivity . 15
5.4.2.1 Description . 15
5.4.2.2 Limits . 15
5.4.3 Blocking . 15
5.4.3.1 Description . 15
5.4.3.2 Limits . 15
5.4.3.3 Conformance . 15
5.4.4 Adjacent Channel Saturation . 15
5.4.4.1 Description . 15
5.4.4.2 Limits . 15
5.4.4.3 Conformance . 15
5.4.5 Spurious Response Rejection . 16
5.4.5.1 Description . 16
5.4.5.2 Limits . 16
5.4.5.3 Conformance . 16
5.4.6 Behaviour at high wanted signal level . 16
5.4.6.1 Description . 16
5.4.6.2 Limits . 16
5.4.6.3 Conformance . 16
6 Bi-Directional Communication with Frequency Agility . 16
6.1 Mode BN Applicability and Conformance Requirements . 16
6.2 Bi-directional Communication and Frequency Agility . 16
6.2.1 Applicability . 16
6.2.2 Acknowledgement . 16
6.2.2.1 Description . 16
6.2.2.2 Limits . 17
6.2.2.3 Conformance . 17
6.2.3 Ability to change communication frequency . 17
6.2.3.1 Description . 17
6.2.3.2 Limits . 17
6.2.3.3 Conformance . 17
6.3 Transmitter Parameters . 17
6.4 Receiver Parameters . 17
6.4.1 Applicability . 17
6.4.2 Adjacent Channel Selectivity . 17
6.4.2.1 Description . 17
6.4.2.2 Limits . 17
6.4.2.3 Conformance . 17
6.4.3 Blocking . 18
6.4.3.1 Description . 18
ETSI
---------------------- Page: 4 ----------------------
5 Draft ETSI EN 303 406 V1.1.0 (2016-05)
6.4.3.2 Limits . 18
6.4.3.3 Conformance . 18
6.4.4 Adjacent Channel Saturation . 18
6.4.4.1 Description . 18
6.4.4.2 Limits . 18
6.4.4.3 Conformance . 18
6.4.5 Spurious Response Rejection . 18
6.4.5.1 Description . 18
6.4.5.2 Limits . 18
6.4.5.3 Conformance . 18
6.4.6 Behaviour at high wanted signal level . 19
6.4.6.1 Description . 19
6.4.6.2 Limits . 19
6.4.6.3 Conformance . 19
7 Testing for compliance with technical requirements . 19
7.1 General . 19
7.2 Presentation of equipment for testing purposes . 19
7.3 Wanted performance criteria . 19
7.3.1 Receiver response . 19
7.4 Radio test suites - Transceivers . 20
7.4.1 Frequency Agility . 20
7.4.1.1 Description . 20
7.4.1.2 Test Conditions . 20
7.4.1.3 Method of measurement . 20
7.4.1.4 Measurement procedure . 20
Annex A (normative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 21
Annex B (normative): Operating bands and technical parameters . 23
Annex C (informative): Selection of technical parameters . 25
C.1 Introduction . 25
C.2 Receiver sensitivity . 25
C.3 Other receiver parameters . 25
C.4 Transmitter short term behaviour . 25
C.5 Listen before talk . 26
Annex D (informative): Bibliography . 27
History . 28
ETSI
---------------------- Page: 5 ----------------------
6 Draft ETSI EN 303 406 V1.1.0 (2016-05)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM), and is now submitted for the combined Public Enquiry and Vote
phase of the ETSI standards EN Approval Procedure.
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.10] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.2].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive and associated
EFTA regulations.
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio equipment within the scope of the Radio Equipment Directive (RED) [i.2].
It is recognized that the radio communications link alone does not determine the overall operation of a system, but that a
functioning radio communications link is an essential foundation upon which a system may be built.
ETSI
---------------------
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.