kSIST FprEN 14037-4:2013

Free hanging heating and cooling surfaces for water with a temperature below 120°C - Part 4: Test method for cooling capacity of ceiling mounted radiant panels

This European Standard defines the technical specifications and requirements for the definition of the cooling capacity of ceiling mounted radiant panels

An der Decke frei abgehängte Heiz- und für Wasser mit einer Temperatur unter 120°C - Teil 4: Prüfverfahren für die Kühlleistung von Deckenstrahlplatten

Diese Europäische Norm legt das Prüfverfahren und die Prüfeinrichtung zur Bestimmung der Kühlleistung von Deckenstrahlplatten nach prEN 14037-1, Abschnitt 3.3.1 fest. Die Prüfung nach dieser Norm setzt eine Prüfung der Wärmeleistung nach prEN 14037-2 des Modells voraus.

Panneaux rayonnants de plafond alimentés en eau à une température inférieure à 120°C - Partie 4: Méthode d'essai de la capacité de refroidissement des panneaux rayonnants de plafond

Stropne sevalne plošče za ogrevanje in hlajenje površin za vodo s temperaturo pod 120°C - 4. del: Preskusne metode zmogljivosti hlajenja sevalnih stropnih plošč

General Information

• Status: Not Published
• Public Enquiry End Date: 28-Feb-2012
• ICS: 91.140.10 - Central heating systems
• ICS: 91.140.60 - Water supply systems
• Technical Committee: OGS - Heating for buildings
• Current Stage: 98 - Abandoned project (Adopted Project)
• Start Date: 27-Sep-2016
• Due Date: 02-Oct-2016
• Completion Date: 27-Sep-2016
• Ref Project: EN 14037-4:2013 - Free hanging heating and cooling surfaces for water with a temperature below 120 °C - Part 4: Test method for cooling capacity of ceiling mounted radiant panels

Relations

• Revised: SIST EN 14037-4:2017 - Free hanging heating and cooling surfaces for water with a temperature below 120°C - Part 4: Pre-fabricated ceiling mounted radiant panels - Test method for cooling capacity
• Effective Date: 01-Apr-2017

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN 14037-4:2012
01-januar-2012
6WURSQHVHYDOQHSORãþH]DRJUHYDQMHLQKODMHQMHSRYUãLQ]DYRGRVWHPSHUDWXUR
SRGƒ&GHO3UHVNXVQHPHWRGH]PRJOMLYRVWLKODMHQMDVHYDOQLKVWURSQLKSORãþ
Free hanging heating and cooling surfaces for water with a temperature below 120°C -
Part 4: Test method for cooling capacity of ceiling mounted radiant panels
An der Decke frei abgehängte Heiz- und für Wasser mit einer Temperatur unter 120°C -
Teil 4: Prüfverfahren für die Kühlleistung von Deckenstrahlplatten
Panneaux rayonnants de plafond alimentés en eau à une température inférieure à 120°C
- Partie 4: Méthode d'essai de la capacité de refroidissement des panneaux rayonnants
de plafond
Ta slovenski standard je istoveten z: prEN 14037-4
ICS:
91.140.10 Sistemi centralnega Central heating systems
ogrevanja
91.140.60 Sistemi za oskrbo z vodo Water supply systems
oSIST prEN 14037-4:2012 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 14037-4:2012

---------------------- Page: 2 ----------------------
oSIST prEN 14037-4:2012


EUROPEAN STANDARD
DRAFT
prEN 14037-4
NORME EUROPÉENNE

EUROPÄISCHE NORM

November 2011
ICS 91.140.30
English Version
Free hanging heating and cooling surfaces for water with a
temperature below 120 °C - Part 4: Test method for cooling
capacity of ceiling mounted radiant panels
Panneaux rayonnants de plafond alimentés en eau à une An der Decke frei abgehängte Heiz- und Kühlflächen für
température inférieure à 120 °C - Partie 4: Méthode d'essai Wasser mit einer Temperatur unter 120 °C - Teil 4:
de la capacité de refroidissement des panneaux rayonnants Prüfverfahren für die Kühlleistung von Deckenstrahlplatten
de plafond
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 130.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 14037-4:2011: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 14037-4:2012
prEN 14037-4:2011 (E)
Contents
Foreword . 3
Introduction . 4
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Testing of cooling capacity . 5
4.1 Short description . 5
4.2 Test booth . 5
4.3 Test methods . 7
5 Carrying out the measurement . 8
5.1 General . 8
5.2 Dimension and construction of the test samples . 8
5.3 Selection of the models to be tested for determining the cooling capacity of a type . 8
5.4 Manufacturer documents for the test samples . 8
5.5 Arrangement of the sample in the test booth . 8
5.6 Upper insulation of the test sample . 8
5.7 Connection of the test sample to the measuring circuit . 8
5.8 Tests . 8
5.9 Mass flow . 8
5.10 Test temperature . 8
5.11 Steady state conditions . 9
5.12 Correction due to the air pressure . 9
5.13 Result of measurement – characteristic equation . 9
5.14 Nominal cooling capacity . 9
6.2 Data . 10
Annex A (informative) Specimen of the test report for cooling capacity . 11
Bibliography . 14


2

---------------------- Page: 4 ----------------------
oSIST prEN 14037-4:2012
prEN 14037-4:2011 (E)
Foreword
This document (prEN 14037-4:2011) has been prepared by Technical Committee CEN/TC 130 “Space heating
appliances without integral heat sources”, the secretariat of which is held by UNI.
This document is currently submitted to the CEN Enquiry.
3

---------------------- Page: 5 ----------------------
oSIST prEN 14037-4:2012
prEN 14037-4:2011 (E)
Introduction
This European Standard results from the recognition that the ceiling mounted heating and cooling surfaces falling
into the field of application hereinafter stated are traded of the basis of their thermal and cooling output. For evalu-
ating and comparing different ceiling mounted radiant panels it is therefore necessary to refer to a single stipulated
value.
The European Standard EN 14037, Free hanging heating and cooling surfaces for water with a temperature below
120°C consists of the following parts:
- Part 1: Technical specifications and requirements
- Part 2: Test method for thermal output of ceiling mounted radiant panels
- Part 3: Rating method and evaluation of radiant thermal output of ceiling mounted radiant panels
- Part 4: Test method for cooling capacity of ceiling mounted radiant panels
- Part 5: Test method for thermal output of open or closed heated ceiling surfaces

1 Scope
This European Standard defines the technical specifications and requirements for the definition of the cooling ca-
pacity of ceiling mounted radiant panels according to the specifications of prEN 14037-1, clause 3.3.1. The test
according to this standard requires the measurement of the thermal output according to prEN 14037-2 of the
model.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated references,
only the edition cited applies. For undated references, the latest edition of the referenced document (including any
amendments) applies.
prEN 14037-1, Free hanging heating and cooling surfaces for water with a temperature below 120°C - Part 1:
Technical specifications and requirements
prEN 14037-2, Free hanging heating and cooling surfaces for water with a temperature below 120°C - Part 2: Test
method for thermal output of ceiling mounted radiant panels
EN ISO/IEC 17025, General requirements for the competence of testing and calibration laboratories
(ISO/IEC 17025:2005)
3 Terms and definitions
For the purposes of this document, the terms and definitions given in prEN 14037-1 apply.
4

---------------------- Page: 6 ----------------------
oSIST prEN 14037-4:2012
prEN 14037-4:2011 (E)
4 Testing of cooling capacity
4.1 Short description
The cooling capacity of the test sample has to be determined in its steady condition with measurements of the wa-
ter flow and the temperature increase in the water. The cooling capacity shall be quoted as function of the tempera-
ture difference between the reference temperature and the average water temperature.
The test is carried out in a testing system according to prEN 14037-2, which consists of a closed booth with con-
trolled temperatures of the inside surfaces plus master panel 1 (according to prEN 14037-2, Clause 6). All laborato-
ries performing tests according to this standard shall participate in inter-laboratory comparison exercises (according
to prEN 14037-2, Clause 6).
For covering the cooling capacity, the test booth will be heated with a number of electrical heated cooling load
simulators which are positioned on the floor of the test booth. To get reproducible results, the simulators have to be
arranged according to 4.2.
4.2 Test booth
The test is carried out in a test booth according to prEN 14037-2, Clause 5.
Differing from these definitions the surfaces, floor and ceiling of the test booth shall be insulated in the way that the
average heat flow in those surfaces is lower than 0,40 W/m² during the test. This heat flow shall be determined by
preliminary calibration tests of the booth or by calculations.
Differing to prEN 14037-2, 5.4 the reference temperature during the measurement shall be 32 °C ± 0,5K in the
steady condition for minimum 30 minutes.

The temperature(s) of inner surfaces of walls, floor and ceiling of the test booth (under the insulation) shall be con-
trolled and be kept on a value, which is necessary to guarantee a max. temperature difference between these sur-
faces and the reference temperature of less than 1,0 K.
The radiant emissivity of the surface of the insulation has to be at least 0,9.
The test booth will be heated with 6 electrical heated cooling load simulators (see figures 1 and 2 ), which are posi-
tioned on the floor of the test booth.
The output of each simulator must not exceed 180 W and shall be continuously adjustable, e.g. with an adjustable
transformer or a thyristor. Each simulator shall have an identical heat output and the same number of bulbs.
The housing of the simulators consists of painted steel sheet. The emissivity of the inside and outside surface shall
be at least 0,9. The active power of the simulators shall be measured with a measuring instrumen
...