SIST EN IEC 62722-1:2022
(Main)Luminaire performance - Part 1: General requirements (IEC 62722-1:2022)
Luminaire performance - Part 1: General requirements (IEC 62722-1:2022)
This part of IEC 62722 covers specific performance and environmental requirements for luminaires, incorporating electric light sources for operation from supply voltages up to 1 000 V. Unless otherwise detailed, performance data covered under the scope of this document are for the luminaires in a condition representative of new manufacture, with any specified initial aging procedures completed.
IEC 62722-1 covers requirements for luminaires to support energy efficient use and responsible environmental management to the end of life. The object of this Part 1 is to provide a set of requirements which are considered to be generally applicable to most types of luminaires. Where additional performance requirements for specific types of light source are relevant, these are specified in the IEC 62722-2 series. The IEC 62722-2 series can also cover a wider scope of performance aspects appropriate to the particular light source technology.
NOTE The structure of these performance standards also allows for the possibility of Part 3 of the IEC 62722 series to be introduced in the future should standardization of performance criteria linked to specific luminaire applications be determined as necessary (e.g. floodlighting, street lighting).
It is the intention that the requirements of this Part 1 are to be met by the provision of information and data provided by the luminaire manufacturer (or responsible vendor). Conformity is considered to be met by the provision of the requested information. Any verification of data is conducted by the measurement requirements of this document.
Semi-luminaires are not covered under the scope of this document.
For some types of luminaire (e.g. decorative or household) the provision of performance data under the scope of this document will not be appropriate.
Arbeitsweise von Leuchten - Teil 1: Allgemeine Anforderungen (IEC 62722-1:2022)
Performance des luminaires - Partie 1: Exigences générales (IEC 62722-1:2022)
IEC 62722-1:2022 est disponible sous forme de IEC 62722-1:2022 RLV qui contient la Norme internationale et sa version Redline, illustrant les modifications du contenu technique depuis l'édition précédente.
L'IEC 62722-1:2022 couvre les exigences de performance et d'environnement spécifiques aux luminaires, qui incorporent des sources lumineuses électriques destinées à fonctionner sous des tensions d'alimentation jusqu'à 1 000 V. Sauf disposition contraire, les données de performance couvertes par le domaine d'application du présent document s'appliquent aux luminaires qui sont dans un état représentatif d'un produit neuf, où toutes les procédures de vieillissement initial spécifiées ont été réalisées. Cette deuxième édition annule et remplace la première édition parue en 2014. Cette édition constitue une révision technique. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition antérieure.
- Des références à l'IEC 63103 ont été ajoutées afin d'appliquer les méthodes de mesurage de la consommation de puissance en mode non actif.
- Les pictogrammes de l'Annexe C ont été mis à jour pour représenter les sources lumineuses modernes.
Tehnične lastnosti svetilk - 1. del: Splošne zahteve (IEC 62722-1:2022)
ICS: 29.140.40
Ta del standarda IEC 62722 zajema posebne okoljske zahteve in zahteve glede zmogljivosti svetilk, ki vključujejo električne svetlobne vire v omrežnem napajanju do 1000 V. Razen če je drugače navedeno, veljajo podatki o delovanju, ki spadajo na področje uporabe tega dokumenta, za nove svetilke, pri katerih so bili opravljeni določeni začetni postopki staranja.
Standard IEC 62722-1 zajema zahteve za svetilke, ki do konca življenjskega cikla podpirajo energijsko učinkovito uporabo in odgovorno ravnanje z okoljem. Cilj 1. dela je zagotavljanje nabora zahtev, ki se smatrajo kot splošno veljavne za večino vrst svetilk. Dodatne zahteve za delovanje, ki so morda ustrezne za posamezno vrsto svetlobnega vira, so določene v skupini standardov IEC 62722-2. Skupina standardov IEC 62722-2 lahko tudi zajema širši nabor vidikov v zvezi z delovanjem, ki so primerni za posamezno tehnologijo svetlobnih virov.
OPOMBA: Struktura teh standardov o zmogljivosti omogoča, da se v prihodnosti vključi 3. del skupine standardov IEC 62722, če bi se kriteriji zmogljivosti, ki so povezani s posamezno uporabo svetilk, po potrebi standardizirali (npr. reflektorska osvetlitev, ulična razsvetljava).
Namen je, da se zahteve 1. dela izpolnijo s pomočjo informacij in podatkov, ki jih zagotovi proizvajalec svetilk (ali odgovorni prodajalec). Smatra se, da je za skladnost poskrbljeno, ko se zagotovijo zahtevane informacije. Vsakršno preverjanje podatkov se izvede ob upoštevanju merilnih zahtev tega dokumenta.
Polsvetilke ne spadajo na področje uporabe tega dokumenta.
Za nekatere vrste svetilk (npr. okrasne svetilke, svetilke v gospodinjstvu) zagotavljanje podatkov o zmogljivosti v okviru tega standarda morda ni ustrezno.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN IEC 62722-1:2022
01-oktober-2022
Nadomešča:
SIST EN 62722-1:2016
Tehnične lastnosti svetilk - 1. del: Splošne zahteve (IEC 62722-1:2022)
Luminaire performance - Part 1: General requirements (IEC 62722-1:2022)
Arbeitsweise von Leuchten - Teil 1: Allgemeine Anforderungen (IEC 62722-1:2022)
Performance des luminaires - Partie 1: Exigences générales (IEC 62722-1:2022)
Ta slovenski standard je istoveten z: EN IEC 62722-1:2022
ICS:
29.140.40 Svetila Luminaires
SIST EN IEC 62722-1:2022 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN IEC 62722-1:2022
---------------------- Page: 2 ----------------------
SIST EN IEC 62722-1:2022
EUROPEAN STANDARD EN IEC 62722-1
NORME EUROPÉENNE
EUROPÄISCHE NORM August 2022
ICS 29.140.40 Supersedes EN 62722-1:2016
English Version
Luminaire performance - Part 1: General requirements
(IEC 62722-1:2022)
Performance des luminaires - Partie 1: Exigences Arbeitsweise von Leuchten - Teil 1: Allgemeine
générales Anforderungen
(IEC 62722-1:2022) (IEC 62722-1:2022)
This European Standard was approved by CENELEC on 2022-07-19. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 62722-1:2022 E
---------------------- Page: 3 ----------------------
SIST EN IEC 62722-1:2022
EN IEC 62722-1:2022 (E)
European foreword
The text of document 34D/1658/FDIS, future edition 2 of IEC 62722-1, prepared by SC 34D
"Luminaires" of IEC/TC 34 "Lighting" was submitted to the IEC-CENELEC parallel vote and approved
by CENELEC as EN IEC 62722-1:2022.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2023-04-19
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2025-07-19
document have to be withdrawn
This document supersedes EN 62722-1:2016 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a Standardization Request given to CENELEC by the
European Commission and the European Free Trade Association.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 62722-1:2022 was approved by CENELEC as a European
Standard without any modification.
2
---------------------- Page: 4 ----------------------
SIST EN IEC 62722-1:2022
EN IEC 62722-1:2022 (E)
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the
relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60050-845 - International Electrotechnical Vocabulary. - -
Lighting
IEC 60598-1 - Luminaires - Part 1: General requirements EN IEC 60598-1 -
and tests
IEC 60598-2 series Luminaires - Part 2-1: Particular EN IEC 60598-2 series
requirements - Fixed general purpose
luminaires
IEC 62722-2 series Luminaire performance - Part 2-1: EN 62722-2 series
Particular requirements for LED luminaires
IEC 63103 2020 Lighting equipment - Non-active mode EN IEC 63103 2020
power measurement
IEC TS 63105 - Lighting systems and related equipment - -
Vocabulary
CIE 034 1977 Road lighting lantern and installation data: - -
photometrics, classification and
performance
CIE 043 1979 Photometry of floodlights - -
CIE 121 1996 The photometry and goniophotometry of - -
luminaires
3
---------------------- Page: 5 ----------------------
SIST EN IEC 62722-1:2022
---------------------- Page: 6 ----------------------
SIST EN IEC 62722-1:2022
IEC 62722-1
®
Edition 2.0 2022-06
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Luminaire performance –
Part 1: General requirements
Performance des luminaires –
Partie 1: Exigences générales
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 29.140.40 ISBN 978-2-8322-3807-3
Warning! Make sure that you obtained this publication from an authorized distributor.
Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 7 ----------------------
SIST EN IEC 62722-1:2022
– 2 – IEC 62722-1:2022 © IEC 2022
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 7
4 General requirements . 8
5 Light sources and components of luminaires . 9
6 Photometric data . 9
7 Electrical data. 9
8 Luminaire efficacy data . 10
9 Environmental data . 10
9.1 Materials information . 10
9.2 Maintenance instructions . 10
9.3 End of life dismantling instructions . 10
Annex A (informative) Use of regional standards. 11
Annex B (normative) Measurement method of total power of luminaires and associated
powers . 12
B.1 General . 12
B.2 Test measurement of luminaire power during normal operation . 12
B.3 Standard test conditions . 12
B.4 Electrical measuring instruments . 12
B.5 Test luminaires . 12
B.6 Test voltage . 12
B.7 Luminaire power . 13
B.8 Luminaire standby power . 13
B.9 Luminaire networked standby power . 13
B.10 Emergency lighting charging power . 13
Annex C (informative) Pictograms to assist the communication of instructions for
maintenance through life and end of life recycling . 14
Annex D (normative) Photometric distribution data for luminaires . 15
D.1 General . 15
D.2 Measurement resolution of photometric distribution data . 15
D.3 Method of comparison and acceptable limits of variation . 15
D.3.1 General . 15
D.3.2 Scenarios for each main half plane: C ; C ; C ; C . 16
0 90 180 270
D.3.3 Scenarios for half plane: C I . 17
max
D.3.4 Compliance . 17
Bibliography . 18
Figure C.1 – Instructions for luminaire servicing . 14
Figure C.2 – Instructions for luminaire cleaning . 14
Figure C.3 – Instructions for end of life dismantling . 14
Table D.1 – Examples of nearest values to be selected for comparison . 16
---------------------- Page: 8 ----------------------
SIST EN IEC 62722-1:2022
IEC 62722-1:2022 © IEC 2022 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
LUMINAIRE PERFORMANCE –
Part 1: General requirements
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent
rights. IEC shall not be held responsible for identifying any or all such patent rights.
IEC 62722-1 has been prepared by subcommittee 34D: Luminaires, of IEC technical committee
34: Lighting. It is an International Standard.
This second edition cancels and replaces the first edition published in 2014. This edition
constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous
edition:
a) The reference to and use of the measurement methods for non-active power consumption
in accordance with IEC 63103 have been added.
b) The pictograms of Annex C have been updated to represent modern light sources.
---------------------- Page: 9 ----------------------
SIST EN IEC 62722-1:2022
– 4 – IEC 62722-1:2022 © IEC 2022
The text of this International Standard is based on the following documents:
Draft Report on voting
34D/1658/FDIS 34D/1660/RVD
Full information on the voting for its approval can be found in the report on voting indicated in
the above table.
The language used for the development of this International Standard is English.
This document was drafted in accordance with ISO/IEC Directives, Part 2, and developed in
accordance with ISO/IEC Directives, Part 1 and ISO/IEC Directives, IEC Supplement, available
at www.iec.ch/members_experts/refdocs. The main document types developed by IEC are
described in greater detail at www.iec.ch/standardsdev/publications.
A list of all parts in the IEC 62722 series, published under the general title Luminaire
performance can be found on the IEC website.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under webstore.iec.ch in the data related to the
specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
---------------------- Page: 10 ----------------------
SIST EN IEC 62722-1:2022
IEC 62722-1:2022 © IEC 2022 – 5 –
INTRODUCTION
This part of IEC 62722 is a performance standard for luminaires (general requirements) and
acknowledges the need for defining performance data to be provided, the presentation of this
data, the basis of its measurement, and the associated tolerances that can be reasonably
expected. Information to support responsible environmental use is also included. Future Parts 2
of the IEC 62722 series can be introduced where additional performance requirements for
specific types of light sources are required. The structure of these performance standards also
allows for the possibility of Part 3 of the IEC 62722 series to be introduced in the future should
standardization of performance criteria linked to specific luminaire applications be determined
as necessary (e.g. floodlighting, street lighting).
---------------------- Page: 11 ----------------------
SIST EN IEC 62722-1:2022
– 6 – IEC 62722-1:2022 © IEC 2022
LUMINAIRE PERFORMANCE –
Part 1: General requirements
1 Scope
This part of IEC 62722 covers specific performance and environmental requirements for
luminaires, incorporating electric light sources for operation from supply voltages up to 1 000 V.
Unless otherwise detailed, performance data covered under the scope of this document are for
the luminaires in a condition representative of new manufacture, with any specified initial aging
procedures completed.
This document covers requirements for luminaires to support energy efficient use and
responsible environmental management to the end of life. The object of this document is to
provide a set of requirements which are considered to be generally applicable to most types of
luminaires. Where additional performance requirements for specific types of light source are
relevant, these are specified in the IEC 62722-2 series. The IEC 62722-2 series can also cover
a wider scope of performance aspects appropriate to the particular light source technology.
Semi-luminaires are not covered under the scope of this document.
For some types of luminaires (e.g. decorative or household) the provision of performance data
under the scope of this document is not appropriate.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies.
For undated references, the latest edition of the referenced document (including any
amendments) applies.
IEC 60050-845, International Electrotechnical Vocabulary (IEV) – Part 845: Lighting (available
at http://www.electropedia.org)
IEC 60598-1, Luminaires – Part 1: General requirements and tests
IEC 60598-2 (all parts), Luminaires – Part 2: Particular requirements
IEC 62722-2 (all parts), Luminaire performance – Part 2: Particular requirements
IEC 63103:2020, Lighting equipment – Non-active mode power measurement
IEC TS 63105, Lighting systems and related equipment – Vocabulary
CIE 034:1977, Road lighting lantern and installation data: Photometrics, classification and
performance
CIE 043:1979, Photometry of floodlights
CIE 121:1996, The photometry and goniophotometry of luminaires
---------------------- Page: 12 ----------------------
SIST EN IEC 62722-1:2022
IEC 62722-1:2022 © IEC 2022 – 7 –
3 Terms and definitions
For the purposes of this document the terms and definitions given in IEC 60598-1,
IEC 60050-845 and IEC TS 63105 and the following apply.
ISO and IEC maintain terminology databases for use in standardization at the following
addresses:
• IEC Electropedia: available at http://www.electropedia.org/
• ISO Online browsing platform: available at http://www.iso.org/obp
3.1
input power
electrical power from the mains supply consumed by the luminaire including the operation of all
electrical components necessary for its intended functioning
3.2
standby mode
mode when the equipment is connected to a supply voltage with the illumination
function off, while capable of being activated by an external trigger not being a trigger from a
network
Note 1 to entry: Examples of external triggers are sensing or timing.
[SOURCE: IEC 63103:2020, 3.10, modified – The domain was changed to cover luminaires.]
3.3
networked standby mode
mode when the equipment is connected to a supply voltage with the illumination
function off, while capable of being activated by an external trigger being a trigger from a
network
[SOURCE: IEC 63103:2020, 3.11, modified – The domain was changed to cover luminaires.]
3.4
standby power
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.