SIST-TS CEN/TS 16892:2016

Plastics - Welding of thermoplastics - Specification of welding procedures

This Technical Specification provides guidance for the minimum content of welding procedure specifications for the following welding processes:
-   hot gas welding: round nozzle, high speed nozzle, wedge;
-   extrusion welding;
-   heated tool welding: butt, socket, wedge;
-   solvent welding: socket;
-   electrofusion welding: socket, saddle.
This Technical Specification applies to the welding of the following products and semi-finished products made of thermoplastic materials:
-   sheet;
-   pipe;
-   fittings;
-   lining membrane.

Kunststoffe - Schweißen von thermoplastischen Kunststoffen - Anforderung von Schweißverfahren

Diese Technische Spezifikation enthält Hinweise zu den Mindestangaben von Schweißanweisungen für folgende Schweißverfahren:
-   Warmgasschweißen: Runddüse, Schnellschweißdüse, Keil;
-   Extrusionsschweißen;
-   Heizelementstumpfschweißen: Stumpfstoß, Muffe, Keil;
-   Quellschweißen: Muffe;
-   Heizwendelschweißen: Muffe, Sattel.
Diese Technische Spezifikation gilt für das Schweißen folgender Produkte und Halbzeuge aus thermoplastischen Materialien:
-   Tafeln;
-   Rohre;
-   Formstücke;
-   Dichtungsbahnen.

Plastiques - Soudage des matériaux termoplastiques - Spécification de modes opératoires de soudage

Polimerni materiali - Varjenje plastomerov - Specifikacija varilnih postopkov

Ta tehnična specifikacija podaja smernice glede minimalne vsebine v specifikacijah postopkov varjenja za naslednje postopke varjenja:
– varjenje z vročim plinom: okrogla šoba, šoba za hitro varjenje, klini;
– ekstrudersko varjenje;
– varjenje z vročimi ploščami: soležni zvari, obojni zvari, klini;
– varjenje s topilom: obojni zvari;
– elektrofuzijsko varjenje: obojni zvari;
Ta tehnična specifikacija se uporablja za varjenje naslednjih izdelkov in polizdelkov iz plastomernih materialov:
– plošče;
– cevi;
– spojniki;
– obložne membrane

General Information

• Status: Published
• Public Enquiry End Date: 29-Sep-2015
• Publication Date: 20-Jan-2016
• ICS: 25.160.10 - Welding processes
• ICS: 83.080.01 - Plastics in general
• Technical Committee: IPMA - Polimer materials and products
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 14-Jan-2016
• Due Date: 20-Mar-2016
• Completion Date: 21-Jan-2016
• Ref Project: CEN/TS 16892:2015 - Plastics - Welding of thermoplastics - Specification of welding procedures

Standards Content (Sample)

SLOVENSKI STANDARD
kSIST-TS FprCEN/TS 16892:2015
01-september-2015
Polimerni materiali - Varjenje plastomerov - Specifikacija varilnih postopkov
Plastics - Welding of thermoplastics - Specification of welding procedures
Kunststoffe - Schweißen von thermoplastischen Kunststoffen - Anforderung von
Schweißverfahren
Plastiques - Soudage des matériaux termoplastiques - Spécification de modes
opératoires de soudage
Ta slovenski standard je istoveten z: FprCEN/TS 16892
ICS:
83.080.01 Polimerni materiali na Plastics in general
splošno
kSIST-TS FprCEN/TS 16892:2015 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

kSIST-TS FprCEN/TS 16892:2015

---------------------- Page: 2 ----------------------

kSIST-TS FprCEN/TS 16892:2015

TECHNICAL SPECIFICATION
FINAL DRAFT
FprCEN/TS 16892
SPÉCIFICATION TECHNIQUE

TECHNISCHE SPEZIFIKATION

July 2015
ICS
English Version
Plastics - Welding of thermoplastics - Specification of welding
procedures
Plastiques - Soudage des matériaux termoplastiques - Kunststoffe - Schweißen von thermoplastischen
Spécification de modes opératoires de soudage Kunststoffen - Anforderung von Schweißverfahren


This draft Technical Specification is submitted to CEN members for formal vote. It has been drawn up by the Technical Committee CEN/TC
249.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.

Warning : This document is not a Technical Specification. It is distributed for review and comments. It is subject to change without notice
and shall not be referred to as a Technical Specification.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. FprCEN/TS 16892:2015 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

kSIST-TS FprCEN/TS 16892:2015
FprCEN/TS 16892:2015 (E)
Contents Page
Foreword . 3
1 Scope. 4
2 Normative references . 4
3 Terms and definitions . 4
4 Technical content of welding procedure specification (WPS) . 5
4.1 General . 5
4.2 Related to the welding organization . 5
4.3 Related to the parent material(s) . 5
4.3.1 Parent material(s) type . 5
4.3.2 Parent material(s) dimensions . 6
4.4 Common to all welding procedures . 6
4.4.1 Joint preparation . 6
4.4.2 Welding process . 6
4.4.3 Joint design . 6
4.4.4 Welding position . 6
4.4.5 Ambient temperature . 6
4.5 Specific to a welding process . 6
4.5.1 Hot gas round nozzle and high speed nozzle welding . 6
4.5.2 Heated tool butt welding . 7
4.5.3 Extrusion welding . 7
4.5.4 Solvent socket welding . 8
4.5.5 Heated tool wedge welding . 8
4.5.6 Hot gas wedge welding . 8
4.5.7 Socket fusion . 8
4.5.8 Electrofusion socket . 9
4.5.9 Electrofusion saddle . 9
Annex A (informative) Welding Procedure Specification (WPS) - Hot gas round nozzle and high speed
nozzle welding . 10
Annex B (informative) Welding Procedure Specification (WPS) - Heated tool butt welding . 11
Annex C (informative) Welding Procedure Specification (WPS) - Extrusion welding . 12
Annex D (informative) Welding Procedure Specification (WPS) - Solvent socket welding . 13
Annex E (informative) Welding Procedure Specification (WPS) - Heated tool wedge welding . 14
Annex F (informative) Welding Procedure Specification (WPS) – Hot gas wedge welding . 15
Annex G (informative) Welding Procedure Specification (WPS) – Socket fusion welding . 16
Annex H (informative) Welding Procedure Specification (WPS) – Electrofusion socket welding . 17
Annex I (informative) Welding Procedure Specification (WPS) – Electrofusion saddle welding . 18
Bibliography . 19

2

---------------------- Page: 4 ----------------------

kSIST-TS FprCEN/TS 16892:2015
FprCEN/TS 16892:2015 (E)
Foreword
This document (FprCEN/TS 16892:2015) has been prepared by Technical Committee CEN/TC 249 “Plastics”,
the secretariat of which is held by NBN.
This document is currently submitted to the Formal Vote.
3

---------------------- Page: 5 ----------------------

kSIST-TS FprCEN/TS 16892:2015
FprCEN/TS 16892:2015 (E)
1 Scope
This Technical Specification provides guidance for the minimum content of welding procedure specifications for
the following welding processes:
— hot gas welding: round nozzle, high speed nozzle, wedge;
— extrusion welding;
— heated tool welding: butt, socket, wedge;
— solvent welding: socket;
— electrofusion welding: socket, saddle.
This Technical Specification applies to the welding of the following products and semi-finished products made of
thermoplastic materials:
— sheet;
— pipe;
— fittings;
— lining membrane.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are indispensable
for its application. For dated references, only the edition cited applies. For undated references, the latest edition
of the referenced document (including any amendments) applies.
EN ISO 6947, Welding and allied processes ― Welding positions (ISO 6947)
3 Terms and definitions
For the purposes of this document, the terms and the following apply.
3.1
welding procedure
specified course of action to be followed in making a weld, including the welding process(es), reference to
materials, welding consumables, preparation, preheating (if necessary), method and control of welding and
necessary equipment to be used
3.2
welding process
technique characterized by the method of softening to obtain permanent assembly
3.3
welding procedure specification (WPS)
document that has been qualified and provides the required variables of the welding procedure to ensure
repeatability during production welding
3.4
work instruction
simplified welding procedure specification (WPS), suitable for direct application
4

---------------------- Page: 6 ----------------------

kSIST-TS FprCEN/TS 16892:2015
FprCEN/TS 16892:2015 (E)
3.5
welding procedure qualification record (WPQR)
record comprising all necessary data needed for qualification of a welding procedure specification
3.6
welding consumable
materials consumed in the making of a weld, including filler material
3.7
essential variable
welding condition that influences the quality of the welded joint and requires qualification
3.8
non essential variable
welding condition addressed in the WPS, but not requiring qualification
3.9
parent material
parts to be joined by welding
3.10
welding organization
organization responsible for the welding production
4 Technical content of welding procedure specification (WPS)
4.1 General
A Welding Procedure Specification (WPS) shall provide all the necessary information required to make a weld.
The minimum information required in a WPS is given in 4.2 to 4.5.
Welding procedure specifications cover a certain range for each essential / non-essential variable.
A work instruction can be prepared for each specific job as part of detailed production planning.
Examples of the WPS format are shown in Annexes A, B, C, D, E, F, G, H, I.
The procedure for measuring each variable should be according to agreed specifications.
4.2 Related to the welding organization
— Identification of the welding organization;
— WPS number;
— Welding Procedure Qualification Record (WPQR) number, if applicable;
— signature of the person responsible for approval, appointed by the welding organization.
4.3 Related to the parent material(s)
4.3.1 Parent material(s) type
— Designation of the material(s) and reference standard(s), if any.
An alternative identification shall be used if a reference standard does not exist.
5

---------------------- Page: 7 ----------------------

kSIST-TS FprCEN/TS 16892:2015
FprCEN/TS 16892:2015 (E)
4.3.2 Parent material(s) dimensions
— Thicknesses (SDR for pipes and spigot fittings);
— nominal diameters (for pipes and fittings).
4.4 Common to all welding procedures
4.4.1 Joint preparation
— Cutting and surface preparation method (e.g. machining or scraping);
— initial cleaning (chemical or mechanical);
— jigging, fixtures, clamping.
4.4.2 Welding process
4.4.3 Joint design
— joint and weld type;
— a sketch of the joint design/configuration and dimensions or reference to standards which provide such
information.
4.4.4 Welding position
— Welding positions (in accordance with EN ISO 6947, where applicable).
4.4.5 Ambient temperature
4.5 Specific to a welding process
4.5.1 Hot gas round nozzle and high speed nozzle welding
— Initial joint geometry;
— weld rod/wire [cross-section geometry e.g. round, triangular, designation of the material(s) and reference
standard(s), dimensions (size)];
— welding speed;
— gas type;
— backing (method and type of backing, backing material and dimensions);
— nozzle diameter;
— gas flow rate;
— gas temperature;
— torch angle;
— rod/wire angle;
— distance between gas nozzle and workpiece (round nozzle welding only);
— interpass cleaning;
6

---------------------- Page: 8 ---------------------
...

SLOVENSKI STANDARD
SIST-TS CEN/TS 16892:2016
01-marec-2016
Polimerni materiali - Varjenje plastomerov - Specifikacija varilnih postopkov
Plastics - Welding of thermoplastics - Specification of welding procedures
Kunststoffe - Schweißen von thermoplastischen Kunststoffen - Anforderung von
Schweißverfahren
Plastiques - Soudage des matériaux termoplastiques - Spécification de modes
opératoires de soudage
Ta slovenski standard je istoveten z: CEN/TS 16892:2015
ICS:
25.160.10 Varilni postopki in varjenje Welding processes
83.080.01 Polimerni materiali na Plastics in general
splošno
SIST-TS CEN/TS 16892:2016 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST-TS CEN/TS 16892:2016

---------------------- Page: 2 ----------------------

SIST-TS CEN/TS 16892:2016


CEN/TS 16892
TECHNICAL SPECIFICATION

SPÉCIFICATION TECHNIQUE

December 2015
TECHNISCHE SPEZIFIKATION
ICS 25.160.10
English Version

Plastics - Welding of thermoplastics - Specification of
welding procedures
Plastiques - Soudage des matériaux termoplastiques - Kunststoffe - Schweißen von thermoplastischen
Spécification de modes opératoires de soudage Kunststoffen - Anforderung von Schweißverfahren
This Technical Specification (CEN/TS) was approved by CEN on 13 November 2015 for provisional application.

The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to
submit their comments, particularly on the question whether the CEN/TS can be converted into a European Standard.

CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS
available promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in
parallel to the CEN/TS) until the final decision about the possible conversion of the CEN/TS into an EN is reached.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TS 16892:2015 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST-TS CEN/TS 16892:2016
CEN/TS 16892:2015 (E)
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Technical content of welding procedure specification (WPS) . 5
4.1 General . 5
4.2 Related to the welding organization . 5
4.3 Related to the parent material(s) . 5
4.3.1 Parent material(s) type . 5
4.3.2 Parent material(s) dimensions . 6
4.4 Common to all welding procedures. 6
4.4.1 Joint preparation . 6
4.4.2 Welding process . 6
4.4.3 Joint design . 6
4.4.4 Welding position . 6
4.4.5 Ambient temperature . 6
4.5 Specific to a welding process . 6
4.5.1 Hot gas round nozzle and high speed nozzle welding . 6
4.5.2 Heated tool butt welding . 7
4.5.3 Extrusion welding . 7
4.5.4 Solvent socket welding. 8
4.5.5 Heated tool wedge welding . 8
4.5.6 Hot gas wedge welding . 8
4.5.7 Socket fusion . 8
4.5.8 Electrofusion socket . 9
4.5.9 Electrofusion saddle . 9
Annex A (informative) Welding Procedure Specification (WPS) - Hot gas round nozzle and high
speed nozzle welding. 10
Annex B (informative) Welding Procedure Specification (WPS) - Heated tool butt welding. 11
Annex C (informative) Welding Procedure Specification (WPS) - Extrusion welding . 12
Annex D (informative) Welding Procedure Specification (WPS) - Solvent socket welding . 13
Annex E (informative) Welding Procedure Specification (WPS) - Heated tool wedge welding . 14
Annex F (informative) Welding Procedure Specification (WPS) – Hot gas wedge welding . 15
Annex G (informative) Welding Procedure Specification (WPS) – Socket fusion welding . 16
Annex H (informative) Welding Procedure Specification (WPS) – Electrofusion socket welding . 17
Annex I (informative) Welding Procedure Specification (WPS) – Electrofusion saddle welding . 18
Bibliography . 19

2

---------------------- Page: 4 ----------------------

SIST-TS CEN/TS 16892:2016
CEN/TS 16892:2015 (E)
European foreword
This document (CEN/TS 16892:2015) has been prepared by Technical Committee CEN/TC 249 “Plastics”,
the secretariat of which is held by NBN.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to announce this Technical Specification: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey
and the United Kingdom.

3

---------------------- Page: 5 ----------------------

SIST-TS CEN/TS 16892:2016
CEN/TS 16892:2015 (E)
1 Scope
This Technical Specification provides guidance for the minimum content of welding procedure
specifications for the following welding processes:
— hot gas welding: round nozzle, high speed nozzle, wedge;
— extrusion welding;
— heated tool welding: butt, socket, wedge;
— solvent welding: socket;
— electrofusion welding: socket, saddle.
This Technical Specification applies to the welding of the following products and semi-finished products
made of thermoplastic materials:
— sheet;
— pipe;
— fittings;
— lining membrane.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
EN ISO 6947, Welding and allied processes - Welding positions (ISO 6947)
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
welding procedure
specified course of action to be followed in making a weld, including the welding process(es), reference to
materials, welding consumables, preparation, preheating (if necessary), method and control of welding
and necessary equipment to be used
3.2
welding process
technique characterized by the method of softening to obtain permanent assembly
3.3
welding procedure specification
WPS
document that has been qualified and provides the required variables of the welding procedure to ensure
repeatability during production welding
3.4
work instruction
simplified welding procedure specification (WPS), suitable for direct application
4

---------------------- Page: 6 ----------------------

SIST-TS CEN/TS 16892:2016
CEN/TS 16892:2015 (E)
3.5
welding procedure qualification record
WPQR
record comprising all necessary data needed for qualification of a welding procedure specification
3.6
welding consumable
materials consumed in the making of a weld, including filler material
3.7
essential variable
welding condition that influences the quality of the welded joint and requires qualification
3.8
non essential variable
welding condition addressed in the WPS, but not requiring qualification
3.9
parent material
parts to be joined by welding
3.10
welding organization
organization responsible for the welding production
4 Technical content of welding procedure specification (WPS)
4.1 General
A Welding Procedure Specification (WPS) shall provide all the necessary information required to make a
weld.
The minimum information required in a WPS is given in 4.2 to 4.5.
Welding procedure specifications cover a certain range for each essential / non-essential variable.
A work instruction can be prepared for each specific job as part of detailed production planning.
Examples of the WPS format are shown in Annexes A, B, C, D, E, F, G, H, I.
The procedure for measuring each variable should be according to agreed specifications.
4.2 Related to the welding organization
— Identification of the welding organization;
— WPS number;
— Welding Procedure Qualification Record (WPQR) number, if applicable;
— signature of the person responsible for approval, appointed by the welding organization.
4.3 Related to the parent material(s)
4.3.1 Parent material(s) type
— Designation of the material(s) and reference standard(s), if any.
An alternative identification shall be used if a reference standard does not exist.
5

---------------------- Page: 7 ----------------------

SIST-TS CEN/TS 16892:2016
CEN/TS 16892:2015 (E)
4.3.2 Parent material(s) dimensions
— Thicknesses (Standard Dimension Ratio (SDR) for pipes and spigot fittings);
— nominal diameters (for pipes and fittings).
4.4 Common to all welding procedures
4.4.1 Joint preparation
— Cutting and surface preparation method (e.g. machining or scraping);
— initial cleaning (chemical or mechanical);
— jigging, fixtures, clamping.
4.4.2 Welding process
4.4.3 Joint design
— Joint and weld type;
— a sketch of the joint design/configuration and dimensions or reference to standards which provide
such information.
4.4.4 Welding position
— Welding positions (in accordance with EN ISO 6947, where applicable).
4.4.5 Ambient temperature
4.5 Specific to a welding process
4.5.1 Hot gas round nozzle and high speed nozzle welding
— Initial joint geometry;
— weld rod/wire [
...