SIST EN 13347:2004
(Main)Copper and copper alloys - Rod and wire for welding and braze welding
Copper and copper alloys - Rod and wire for welding and braze welding
This European Standard specifies the composition, property requirements and dimensional tolerances for copper and copper alloy rod and wire intended for welding and braze welding purposes.
The sampling procedures, the methods of test for verification of conformity to the requirements of this standard, and the delivery conditions are also specified.
Kupfer und Kupferlegierungen - Stangen und Drähte für Schweißzusatzwerkstoffe und Fugenlote
Diese Europäische Norm legt die Zusammensetzung, die Anforderungen an die Eigenschaften und Grenzabmaße für Stangen und Drähte aus Kupfer und Kupferlegierungen für Schweißzusatzwerkstoffe und Hartlote fest. Der Ablauf der Probenentnahme, die Prüfverfahren zur Feststellung der Übereinstimmung mit den Anforderungen dieser Norm und die Lieferbedingungen sind ebenfalls festgelegt.
Cuivre et alliages de cuivre - Barres et fils pour soudage et brasage
La présente Norme européenne spécifie la composition, les caractéristiques et les tolérances dimensionnelles des barres et fils en cuivre et alliages de cuivre destinés au soudage et au brasage.
Les modes opératoires d'échantillonnage, les méthodes d'essai pour la vérification de la conformité aux exigences de la présente norme et les conditions de livraison sont également spécifiées.
Baker in bakrove zlitine – Palice in žice za varjenje in trdo spajkanje
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Baker in bakrove zlitine – Palice in žice za varjenje in trdo spajkanjeKupfer und Kupferlegierungen - Stangen und Drähte für Schweißzusatzwerkstoffe und FugenloteCuivre et alliages de cuivre - Barres et fils pour soudage et brasageCopper and copper alloys - Rod and wire for welding and braze welding77.150.30Bakreni izdelkiCopper products25.160.20Potrošni material pri varjenjuWelding consumablesICS:Ta slovenski standard je istoveten z:EN 13347:2002SIST EN 13347:2004en01-januar-2004SIST EN 13347:2004SLOVENSKI
STANDARD
SIST EN 13347:2004
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 13347December 2002ICS 25.160.20; 25.160.50; 77.150.30English versionCopper and copper alloys - Rod and wire for welding and brazeweldingCuivre et alliages de cuivre - Barres et fils pour soudage etbrasageKupfer und Kupferlegierungen - Stangen und Drähte fürSchweißzusatzwerkstoffe und FugenloteThis European Standard was approved by CEN on 23 October 2002.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2002 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13347:2002 ESIST EN 13347:2004
EN 13347:2002 (E)2ContentspageForeword.31Scope.42Normative references.43Terms and definitions.44Designations.54.1Material.54.2Product.55Ordering information.66Requirements.66.1Composition.66.2Dimensions and tolerances.77Sampling.78Test methods.78.1Analysis.78.2Rounding of results.89Declaration of conformity and inspection documentation.99.1Declaration of conformity.99.2Inspection documentation.910Marking, labelling, packaging.910.1General.910.2Marking and labelling.910.3Packaging.9Table 1 — Composition of copper.10Table 2 — Composition of miscellaneous copper alloys.11Table 3 — Composition of copper-zinc alloys.12Table 4 — Composition of cooper-tin alloys.13Table 5 — Composition of copper-aluminium alloys.13Table 6 — Composition of copper-nickel-zinc alloys.13Table 7 — Available diameters and tolerances on diameter (including circularity).15Table 8 — Tolerances on length of "nominal length" rod.15Table 9 — Dimensions of preferred spool sizes.16Table 10 — Maximum masses for wire on spools.17Table 11 — Sampling rate.17Bibliography.18SIST EN 13347:2004
EN 13347:2002 (E)3ForewordThis document (EN 13347:2002) has been prepared by Technical Committee CEN/TC 133 "Copper and copperalloys", the Secretariat of which is held by DIN.This European Standard shall be given the status of a national standard, either by publication of an identical text orby endorsement, at the latest by June 2003, and conflicting national standards shall be withdrawn at the latest byJune 2003.Within its programme of work, Technical Committee CEN/TC 133 requested CEN/TC 133/WG 4 "Rod/bar, wire,profiles" to prepare the following standard:EN 13347, Copper and copper alloys — Rod and wire for welding and braze welding.This is one of a series of European Standards for copper and copper alloy products in rod, wire and profile form.Other products are specified as follows:EN 12163, Copper and copper alloys — Rod for general purposes.EN 12164, Copper and copper alloys — Rod for free machining purposes.EN 12165, Copper and copper alloys — Wrought and unwrought forging stock.EN 12166, Copper and copper alloys — Wire for general purposes.EN 12167, Copper and copper alloys — Profiles and rectangular bar for general purposes.EN 12168, Copper and copper alloys — Hollow rod for free machining purposes.prEN 13601, Copper and copper alloys — Copper rod, bar and wire for general electrical purposes.prEN 13602, Copper and copper alloys — Drawn, round copper wire for the manufacture of electrical conductors.According to CEN/CENELEC Internal Regulations, the national standards organizations of the following countriesare bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France,Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden,Switzerland and the United Kingdom.SIST EN 13347:2004
EN 13347:2002 (E)41 ScopeThis European Standard specifies the composition, property requirements and dimensional tolerances for copperand copper alloy rod and wire intended for welding and braze welding purposes.The sampling procedures, the methods of test for verification of conformity to the requirements of this standard,and the delivery conditions are also specified.2 Normative referencesThis European Standard incorporates, by dated or undated reference, provisions from other publications. Thesenormative references are cited at the appropriate places in the text and the publications are listed hereafter. Fordated references, subsequent amendments to or revisions of any of these publications apply to this EuropeanStandard only when incorporated in it by amendment or revision. For undated references, the latest edition of thepublication referred to applies (including amendments).EN 1044, Brazing — Filler metals.EN 1655, Copper and copper alloys — Declarations of conformity.EN 1976, Copper and copper alloys — Cast unwrought copper products.NOTEInformative references to documents used in the preparation of this standard, and cited at the appropriateplaces in the text, are listed in the bibliography.3 Terms and definitionsFor the purposes of this European Standard, the following terms and definitions apply.3.1wiresolid wrought product of uniform circular cross-section along its whole length supplied in coil form or on spools,reels or in drums3.2rodsolid wrought product of uniform circular cross-section along its whole length, supplied in straight lengths3.3circularitydifference between the maximum and the minimum diameters measured at any cross-section of a round rod or wire3.4knurlembossed finish applied to the surface of the wire or rod to aid the adhesion of subsequently applied flux coatingsSIST EN 13347:2004
EN 13347:2002 (E)54 Designations4.1 Material4.1.1 GeneralThe material is designated either by symbol or number (see Tables 1 to 6).4.1.2 SymbolThe material symbol designation is based on the designation system given in ISO 1190-1.NOTEAlthough material symbol designations used in this standard might be the same as those in other standards usingthe designation system given in ISO 1190-1, the detailed composition requirements are not necessarily the same.4.1.3 NumberThe material number designation is in accordance with the system given in EN 1412.4.2 ProductThe product designation provides a standardized pattern of designation from which a rapid and unequivocal de-scription of a product is conveyed in communication. It provides mutual comprehension at the international levelwith regard to products which meet the requirements of the relevant European Standard.The product designation is no substitute for the full content of the standard.The product designation for products to this standard shall consist of:¾ denomination (Rod or Wire);¾ number of this European Standard (EN 13347);¾ material designation, either symbol or number (see Tables 1 to 6);¾ nominal diameter.The derivation of a product designation is shown in the following example.EXAMPLERod for welding/braze welding to this standard, in material designated either CuSn6 or CF452K, nominaldiameter 2,4 mm, shall be designated as follows:Rod EN 13347 — CuSn6 — 2,4orRod EN 13347 — CF452K — 2,4Denomination Number of this European Standard Material designation Nominal diameter in millimetres SIST EN 13347:2004
EN 13347:2002 (E)65 Ordering informationIn order to facilitate the enquiry, order and confirma
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.