SIST EN 10218-2:2012
(Main)Steel wire and wire products - General - Part 2: Wire dimensions and tolerances
Steel wire and wire products - General - Part 2: Wire dimensions and tolerances
This European Standard specifies the tolerances on diameter of round wire and, where applicable, on the length of round wire cut to length, for bright steel wire, (i.e. uncoated), metallic coated steel wire and non-metallic coated steel wire.
This European Standard should not be applied where other requirements for dimensions and tolerances are specified in a particular product standard.
Stahldraht und Drahterzeugnisse - Allgemeines - Teil 2: Drahtmaße und Toleranzen
Diese Europäische Norm legt die Grenzabmaße fest für den Durchmesser von rundem Draht und, soweit zutreffend, für die Länge von zu Stäben geschnittenem runden Draht, und zwar für blanken Stahldraht (d. h. ohne Überzug), für Stahldraht mit metallischem Überzug und für Stahldraht mit nichtmetallischem Überzug.
Diese Europäische Norm sollte nicht angewendet werden, wenn in einer be¬sonderen Erzeugnisnorm andere Anforderungen für Maße und Grenz¬abmaße festgelegt sind.
Fils et produits tréfilés en acier - Généralités - Partie 2: Dimensions et tolérances des fils
Cette Norme européenne spécifie les tolérances de diamètre des fils de section circulaire et, le cas échéant, les tolérances de longueur des fils de section circulaire coupés à longueur pour les fils en acier blanc (c'est-à-dire non revêtus), les fils en acier à revêtement métallique et les fils en acier à revêtement non métallique.
Cette Norme européenne n'est pas applicable lorsqu'une norme de produit spécifique définit d'autres exigences relatives aux dimensions et aux tolérances.
Jeklena žica in žični izdelki - Splošno - 2. del: Mere žic in tolerance
Ta evropski standard določa tolerance za premer okrogle žice in po potrebi dolžino odrezane okrogle žice za svetlo jekleno žico (tj. neprevlečeno), kovinsko prevlečeno jekleno žico in nekovinsko prevlečeno jekleno žico. Ta evropski standard se ne bi smel uporabljati, kadar so v posameznem standardu za izdelek določene druge zahteve v zvezi z merami in tolerancami.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.HUDQFHStahldraht und Drahterzeugnisse - Allgemeines - Teil 2: Drahtmaße und ToleranzenFils et produits tréfilés en acier - Généralités - Partie 2: Dimensions et tolérances des filsSteel wire and wire products - General - Part 2: Wire dimensions and tolerances77.140.65Jeklene žice, jeklene vrvi in verigeSteel wire, wire ropes and link chainsICS:Ta slovenski standard je istoveten z:EN 10218-2:2012SIST EN 10218-2:2012en,fr,de01-marec-2012SIST EN 10218-2:2012SLOVENSKI
STANDARDSIST EN 10218-2:19971DGRPHãþD
SIST EN 10218-2:2012
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 10218-2
January 2012 ICS 77.140.65 Supersedes EN 10218-2:1996English Version
Steel wire and wire products - General - Part 2: Wire dimensions and tolerances
Fils et produits tréfilés en acier - Généralités - Partie 2 : Dimensions et tolérances des fils
Stahldraht und Drahterzeugnisse - Allgemeines - Teil 2: Drahtmaße und Toleranzen This European Standard was approved by CEN on 3 September 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 10218-2:2012: ESIST EN 10218-2:2012
EN 10218-2:2012 (E) 2 Contents Page Foreword .31 Scope .42 Normative references .43 Terms and definitions .44 Wire diameter tolerance .54.1 Tolerance on diameter of uncoated and metallic coated round steel wire .54.1.1 General .54.1.2 Out of roundness (ovality) .64.2 Tolerances on diameter of organic coated wire .74.2.1 General .74.2.2 Extruded organic coating .74.2.3 Sintered organic coating .75 Tolerance on cut lengths .85.1 Tolerance on length .85.2 Tolerance and straightness .96 Length of wire in coil .9 SIST EN 10218-2:2012
EN 10218-2:2012 (E) 3 Foreword This document (EN 10218-2:2012) has been prepared by Technical Committee ECISS/TC 106 “Wire rod and wires”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by July 2012, and conflicting national standards shall be withdrawn at the latest by July 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 10218-2:1996. The standard will comprise the following parts: Part 1: Test methods; Part 2: Wire dimensions and tolerances. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. SIST EN 10218-2:2012
EN 10218-2:2012 (E) 4 1 Scope This European Standard specifies the tolerances on diameter of round wire and, where applicable, on the length of round wire cut to length, for bright steel wire, (i.e. uncoated), metallic coated steel wire and non-metallic coated steel wire. This European Standard should not be applied where other requirements for dimensions and tolerances are specified in a particular product standard. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 10079:2007, Definition of steel products 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 wire product of constant full cross section along its length, obtained by cold drawing rod through a reducing die or passing under pressure between rollers and rewinding the drawn product NOTE 1
The cross section is generally round, though sometimes oval, rectangular, square, hexagonal, octagonal or other convex section. NOTE 2
The manufacturing processes give close control of geometric (size, surface condition) and mechanical properties. Wire may be supplied uncoated (as drawn, annealed) or coated (e.g. wi
...
SLOVENSKI STANDARD
oSIST prEN 10218-2:2008
01-september-2008
-HNOHQDåLFDLQåLþQLL]GHONL6SORãQRGHO 0HUHåLFLQWROHUDQFH
Steel wire and wire products - General - Part 2: Wire dimensions and tolerances
Stahldraht und Drahterzeugnisse - Allgemeines - Teil 2: Drahtmaße und Toleranzen
Fils et produits tréfilés en acier - Généralités - Partie 2: Dimensions et tolérances des fils
Ta slovenski standard je istoveten z: prEN 10218-2
ICS:
77.140.65 Jeklene žice, jeklene vrvi in Steel wire, wire ropes and
verige link chains
oSIST prEN 10218-2:2008 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 10218-2:2008
---------------------- Page: 2 ----------------------
oSIST prEN 10218-2:2008
EUROPEAN STANDARD
DRAFT
prEN 10218-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2008
ICS 77.140.65 Will supersede EN 10218-2:1996
English Version
Steel wire and wire products - General - Part 2: Wire dimensions
and tolerances
Fils et produits tréfilés en acier - Généralités - Partie 2: Stahldraht und Drahterzeugnisse - Allgemeines - Teil 2:
Dimensions et tolérances des fils Drahtmaße und Toleranzen
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee ECISS/TC 30.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the
same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 10218-2:2008: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 10218-2:2008
prEN 10218-2:2008 (E)
Contents Page
Foreword.3
1 Scope.4
2 Normative references.4
3 Terms and definitions .4
4 Wire diameter tolerance .5
4.1 Tolerance on diameter of uncoated and metallic coated round steel wire .5
4.1.1 General.5
4.1.2 Out of roundness (ovality) .6
4.2 Tolerances on diameter of organic coated wire.8
4.2.1 Extruded organic coating .8
4.2.2 Sintered organic coating.8
5 Tolerance on cut lengths .9
5.1 Tolerance on length.9
5.2 Tolerance and straightness.9
6 Length of wire in coil.10
2
---------------------- Page: 4 ----------------------
oSIST prEN 10218-2:2008
prEN 10218-2:2008 (E)
Foreword
This document (prEN 10218-2:2008) has been prepared by Technical Committee ECISS/TC 30 “Steel wires”,
the secretariat of which is held by AFNOR.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 10218-2:1996.
The standard will comprise the following parts:
Part 1: Test methods
Part 2: Wire dimensions and tolerances
3
---------------------- Page: 5 ----------------------
oSIST prEN 10218-2:2008
prEN 10218-2:2008 (E)
1 Scope
This part of the European standard specifies the tolerances on diameter of round wire and, where applicable,
on the length of round wire cut to length, for bright steel wire, (i.e. uncoated), metallic coated steel wire and
non-metallic coated steel wire.
This standard should not be applied where other requirements for dimensions and tolerances are specified in
a particular product standard.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
EN 10079, Definition of steel products.
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
wire
as well as being supplied in the uncoated (bright) condition, wire can also be supplied with metallic or non-
metallic coatings or both
The metallic coating can be as a finished coating or as a drawn finished coating.
[For definition of wire, see EN 10079]
3.2
cut length
a straightened piece of wire cut to a specified length
4
---------------------- Page: 6 ----------------------
oSIST prEN 10218-2:2008
prEN 10218-2:2008 (E)
4 Wire diameter tolerance
4.1 Tolerance on diameter of uncoated and metallic coated round steel wire
4.1.1 General
Key
1 metallic coating th
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.