Inland navigation vessels - Outboard ladders

This document applies to outboard ladders for inland navigation vessels. Outboard ladders are used on inland navigation vessels having great side heights to facilitate safe climbing into ship's boats, safe disembarking or safe crossing over onto vessels in the case of significantly different boarding heights.
This document specifies safety requirements on design, dimensions and strength and test conditions for outboard ladders.
Outboard ladders are intended for that range where boarding stairs according to EN 1502 are not sufficient in length. This range starts at a boarding height of approximately at 2,8 m above the light water-line.
Boarding ladders are not intended for use by passengers.

Fahrzeuge der Binnenschifffahrt - Außenbordleitern

Dieses Dokument gilt für Außenbordleitern für Fahrzeuge der Binnenschifffahrt. Außenbordleitern werden auf Fahrzeugen der Binnenschifffahrt mit großer Seitenhöhe eingesetzt, um den sicheren Einstieg in Beiboote, den sicheren Übergang zum Land oder das sichere Übersteigen zu benachbarten Schiffen bei sehr unterschiedlichen Bordhöhen zu ermöglichen.
Dieses Dokument legt Sicherheitsanforderungen an Bauart, Maße und Festigkeit sowie Prüfbedingungen für Außenbordleitern fest.
Außenbordleitern sind für den Bereich vorgesehen, in dem Außenbordtreppen nach EN 1502 bezüglich ihrer Länge nicht ausreichen. Dieser Bereich beginnt bei einer Bordhöhe von ungefähr 2,8 m über der Leerwasserlinie.
Außenbordleitern sind nicht für die Benutzung durch Fahrgäste vorgesehen.

Bateaux de navigation intérieure - Échelles de bordé

Le présent document s’applique aux échelles de bordé pour les bateaux de navigation intérieure. Les échelles de bordé sont utilisées sur les bateaux de navigation intérieure avec de grandes hauteurs de muraille pour assurer la sécurité des transferts vers les canots, du débarquement sur la terre ferme ou du passage sur des navires à pont inférieur lorsque les hauteurs pour l’embarquement sont significativement différentes.
Le présent document spécifie les exigences de sécurité relatives à la conception, aux dimensions, à la résistance et aux conditions d’essai pour les échelles de bordé.
Les échelles de bordé sont conçues pour la gamme de bateaux de navigation intérieure pour lesquels les escaliers de bordaille conformes à l’EN 1502 ne sont pas suffisamment longs. Cette gamme démarre à une hauteur de bord de plus d’environ 2,8 m au-dessus de la ligne d’eau à vide.
Les échelles de bordé ne sont pas destinées à être utilisées par les passagers.

Plovila za celinske vode - Zunanje lestve

General Information

Status
Not Published
Public Enquiry End Date
10-May-2022
Technical Committee
Current Stage
4020 - Public enquire (PE) (Adopted Project)
Start Date
23-Feb-2022
Due Date
13-Jul-2022

RELATIONS

Buy Standard

Draft
oSIST prEN 17361:2022
English language
13 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (sample)

SLOVENSKI STANDARD
oSIST prEN 17361:2022
01-april-2022
Plovila za celinske vode - Zunanje lestve
Inland navigation vessels - Outboard ladders
Fahrzeuge der Binnenschifffahrt - Außenbordleitern
Bateaux de navigation intérieure - Échelles de bordé
Ta slovenski standard je istoveten z: prEN 17361
ICS:
47.020.10 Ladijski trupi in njihovi Hulls and their structure
konstrukcijski elementi elements
47.060 Jezerska in rečna plovila Inland navigation vessels
97.145 Lestve Ladders
oSIST prEN 17361:2022 en,fr,de

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 17361:2022
---------------------- Page: 2 ----------------------
oSIST prEN 17361:2022
DRAFT
EUROPEAN STANDARD
prEN 17361
NORME EUROPÉENNE
EUROPÄISCHE NORM
February 2022
ICS 47.020.10; 47.060 Will supersede EN 17361:2020
English Version
Inland navigation vessels - Outboard ladders

Bateaux de navigation intérieure - Échelles de bordé Fahrzeuge der Binnenschifffahrt - Außenbordleitern

This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee

CEN/TC 15.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations

which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other

language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC

Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,

Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,

Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and

United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are

aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without

notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels

© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 17361:2022 E

worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 17361:2022
prEN 17361:2022 (E)
Contents Page

European foreword ....................................................................................................................................................... 3

1 Scope .................................................................................................................................................................... 4

2 Normative references .................................................................................................................................... 4

3 Terms and definitions ................................................................................................................................... 4

4 Safety requirements ....................................................................................................................................... 5

4.1 Dimensions ........................................................................................................................................................ 5

4.2 Parts ..................................................................................................................................................................... 5

4.2.1 General ................................................................................................................................................................ 5

4.2.2 Stringer and handhold .................................................................................................................................. 5

4.2.3 Steps ..................................................................................................................................................................... 5

4.2.4 Spacers ................................................................................................................................................................ 6

4.2.5 Web....................................................................................................................................................................... 7

4.3 Holder of the outboard ladder ................................................................................................................... 7

4.3.1 General ................................................................................................................................................................ 7

4.3.2 Type A .................................................................................................................................................................. 7

4.3.3 Type B .................................................................................................................................................................. 8

4.4 Adjustable hook (H) ....................................................................................................................................... 8

4.4.1 Dimensions ........................................................................................................................................................ 8

4.4.2 Fasteners ............................................................................................................................................................ 8

4.5 Assembly ............................................................................................................................................................ 9

4.6 Strength ........................................................................................................................................................... 10

5 Construction ................................................................................................................................................... 10

5.1 Watertightness .............................................................................................................................................. 10

5.2 Buoyancy ......................................................................................................................................................... 10

5.3 Safe tread ........................................................................................................................................................ 10

5.4 Mass ................................................................................................................................................................... 10

5.5 Materials .......................................................................................................................................................... 10

6 Testing .............................................................................................................................................................. 11

6.1 General ............................................................................................................................................................. 11

6.2 Test of materials ........................................................................................................................................... 11

6.3 Strength test ................................................................................................................................................... 11

6.3.1 Outboard ladder ........................................................................................................................................... 11

6.3.2 Handhold ......................................................................................................................................................... 11

6.3.3 Adjustable hook ............................................................................................................................................ 11

6.4 Bouyancy test ................................................................................................................................................. 11

7 Designation..................................................................................................................................................... 11

8 Marking ............................................................................................................................................................ 12

Bibliography ................................................................................................................................................................. 13

---------------------- Page: 4 ----------------------
oSIST prEN 17361:2022
prEN 17361:2022 (E)
European foreword

This document (prEN 17361:2022) has been prepared by Technical Committee CEN/TC 15 “Inland

navigation vessels”, the secretariat of which is held by DIN.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 17361:2020.
Compared to to EN 17361:2020, the following changes have been made:
a) subclause 5.1 has been replaced by the Clause “Watertightness”;
b) subclause 5.4 has been deleted.
---------------------- Page: 5 ----------------------
oSIST prEN 17361:2022
prEN 17361:2022 (E)
1 Scope

This document applies to outboard ladders for inland navigation vessels. Outboard ladders are used on

inland navigation vessels having great side heights to facilitate safe climbing into ship's boats, safe

disembarking or safe crossing over onto vessels in the case of significantly different boarding heights.

This document specifies safety requirements on design, dimensions and strength and test conditions for

outboard ladders.

Outboard ladders are intended for that range where boarding stairs according to EN 1502 are not

sufficient in length. This range starts at a boarding height of approximately at 2,8 m above the light water-

line.
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.