SIST EN 62841-2-14:2015

Electric Motor- Operated Hand-Held Tools, Transportable Tools and Lawn and Garden Machinery - Safety - Part 2-14: Particular requirements for hand-held planers

This clause of SIST EN 62841-2-14 is applicable, except as follows: Addition: This part of IEC 62841 applies to planers.

Elektrische motorbetriebene handgeführte Werkzeuge, transportable Werkzeuge und Rasen- und Gartenmaschinen - Sicherheit - Teil 2-14: Besondere Anforderungen für handgeführte Hobel

Outils électroportatifs à moteur, outils portables et machines pour jardins et pelouses - Sécurité - Partie 2-14: Exigences particulières pour les raboteuses portatives

IEC 62841-2-14:2015 s’applique aux rabots portatifs, la tension assignée est inférieure à 250 V pour les outils à courant monophasé alternatif ou continu, et inférieure à 480 V pour les outils à courant alternatif triphasé. La tension assignée est inférieure à 3 700 W. Les limites d'application de la présente Norme aux outils fonctionnant sur batterie sont indiquées en K.  La présente Norme traite des dangers présentés par les outils, encourus par tous les individus dans l'utilisation normale et dans l'utilisation impropre raisonnablement prévisible de ces outils. Les outils comportant des éléments chauffants électriques entrent dans le domaine d'application de la présente Norme. Les outils électroportatifs, qui peuvent être montés sur un support de travail pour être utilisés comme outils installés à poste fixe sans aucune modification de l'outil lui-même, sont compris dans le domaine d'application de la présente Norme et la combinaison d'un outil portatif et d'un support est considérée comme un outil portable, donc couvert par la Partie 3 applicable.  L’attention des Comités Nationaux est attirée sur le fait que les fabricants d’appareils et les organismes d’essai peuvent avoir besoin d’une période transitoire après la parution d’une nouvelle publication IEC, ou d’une publication amendée ou révisée, pour fabriquer des produits conformes aux nouvelles exigences et pour adapter leurs équipements aux nouveaux essais ou aux essais révisés.  Le comité recommande que le contenu de cette publication soit entériné au niveau national au plus tôt 36 mois après la date de publication.
La présente Partie 2-14 doit être utilisée conjointement avec la première édition de l’IEC 62841-1:2014.
Mots clés: rabots, portatif, tête de coupe

Električna motorna ročna orodja, prenosna orodja ter stroji za trato in vrt - Varnost - 2-14. del: Posebne zahteve za ročne skobeljnike

Ta točka standarda SIST EN 62841-2-14 velja, razen kot sledi: Dodatek: Ta del standarda IEC 62841 se uporablja za skobeljnike.

General Information

• Status: Published
• Publication Date: 09-Nov-2015
• ICS: 25.080.25 - Planing machines
• ICS: 25.140.20 - Electric tools
• Technical Committee: VGA - Safety of household and similar electrical appliances
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 05-Nov-2015
• Due Date: 10-Jan-2016
• Completion Date: 10-Nov-2015
• Directive: 2006/42/EC - Directive 2006/42/EC of the European Parliament and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast)
• Mandate: M/396 - Mandate to CEN and Cenelec for standardisation in the field of machinery
• Ref Project: EN 62841-2-14:2015 - Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery - Safety - Part 2-14: Particular requirements for hand-held planers

Relations

• Replaces: SIST EN 60745-2-14:2009/A2:2010 - Hand-held motor-operated electric tools - Safety - Part 2-14: Particular requirements for planers (IEC 60745-2-14:2003/A2:2010)
• Effective Date: 01-Dec-2015
• Replaces: SIST EN 60745-2-14:2009 - Hand-held motor-operated electric tools - Safety -- Part 2-14: Particular requirements for planers
• Effective Date: 01-Dec-2015

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 62841-2-14:2015
01-december-2015
1DGRPHãþD
SIST EN 60745-2-14:2009
SIST EN 60745-2-14:2009/A2:2010
(OHNWULþQDPRWRUQDURþQDRURGMDSUHQRVQDRURGMDWHUVWURML]DWUDWRLQYUW9DUQRVW
GHO3RVHEQH]DKWHYH]DURþQHVNREHOMQLNH
Electric Motor- Operated Hand-Held Tools, Transportable Tools and Lawn and Garden
Machinery - Safety - Part 2-14: Particular requirements for hand-held planers
Ta slovenski standard je istoveten z: EN 62841-2-14:2015
ICS:
25.080.25 6WURML]DSORãþLQVNRREGHODYR Planing machines
25.140.20 (OHNWULþQDRURGMD Electric tools
SIST EN 62841-2-14:2015 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 62841-2-14:2015

---------------------- Page: 2 ----------------------

SIST EN 62841-2-14:2015


EUROPEAN STANDARD EN 62841-2-14

NORME EUROPÉENNE

EUROPÄISCHE NORM
October 2015
ICS 25.140.20 Supersedes EN 60745-2-14:2009
English Version
Electric motor-operated hand-held tools, transportable tools and
lawn and garden machinery - Safety - Part 2-14: Particular
requirements for hand-held planers
(IEC 62841-2-14:2015 , modified)
Outils électroportatifs à moteur, outils portables et machines Elektrische motorbetriebene handgeführte Werkzeuge,
pour jardins et pelouses - Sécurité - Partie 2-14: Exigences transportable Werkzeuge und Rasen- und
particulières pour les raboteuses portatives Gartenmaschinen - Sicherheit - Teil 2-14: Besondere
(IEC 62841-2-14:2015 , modifiée) Anforderungen für handgeführte Hobel
(IEC 62841-2-14:2015 , modifiziert)
This European Standard was approved by CENELEC on 2015-08-31. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN 62841-2-14:2015 E

---------------------- Page: 3 ----------------------

SIST EN 62841-2-14:2015
EN 62841-2-14:2015
European foreword
The text of document 116/222/FDIS, future edition 1 of IEC 62841-2-14, prepared by IEC/TC 116 "Safety
of motor-operated electric tools" was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN 62841-2-14:2015.
A draft amendment, which covers common modifications to IEC 62841-2-14:2015 (116/222/FDIS), was
prepared by CLC/TC 116, "Safety of motor-operated electric tools" and approved by CENELEC.
The following dates are fixed:
(dop) 2016-08-31
• latest date by which the document has to be implemented at
national level by publication of an identical national
standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2019-08-31
document have to be withdrawn

This document will supersede EN 60745-2-14:2009 + A2:2010.
This European Standard is divided into four parts:
Part 1: General requirements which are common to most hand-held electric motor operated tools
(for the purpose of this standard referred to simply as tools) which could come within the
scope of this standard;
Part 2, 3 or 4: Requirements for particular types of tools which either supplement or modify the
requirements given in Part 1 to account for the particular hazards and characteristics of
these specific tools.
This Part 2 is to be used in conjunction with EN 62841-1:2015. When this standard states "addition",
"modification" or "replacement", the relevant text in Part 1 is to be adapted accordingly.
This Part 2 supplements or modifies the corresponding clauses in EN 62841-1:2015, so as to convert it
into the European Standard: Particular requirements for hand-held planers.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent
rights.
This document has been prepared under a mandate given to CENELEC by the European Commission
and the European Free Trade Association and supports essential requirements of EU Directive(s).
For the relationship with EU Directive(s), see informative Annex ZZ, which is an integral part of this
document.
Compliance with the clauses of Part 1 together with this Part 2 provides one means of conforming with
the essential health and safety requirements of the Directive concerned.
2

---------------------- Page: 4 ----------------------

SIST EN 62841-2-14:2015
EN 62841-2-14:2015
Warning: Other requirements and other EU Directives can be applicable to the products falling within
the scope of this standard.
This European Standard follows the overall requirements of EN ISO 12100.
The following print types are used:
- requirements; in roman type
- test specifications: in italic type;
- notes: in smaller roman type.
The terms defined in Clause 3 are printed in bold typeface.
Subclauses, notes, tables and figures which are additional to those in Part 1 are numbered starting
from 101.
Clauses, subclauses, notes, tables, figures and annexes which are additional to those in
IEC 62841-2-14:2015 are prefixed “Z”.
3

---------------------- Page: 5 ----------------------

SIST EN 62841-2-14:2015
EN 62841-2-14:2015
Endorsement notice
The text of the International Standard IEC 62841-2-14:2015 was approved by CENELEC as a European
Standard with agreed common modifications.
COMMON MODIFICATIONS
21 Construction
Replace the existing subclause 21.18.1.1 with the following:
21.18.1.1 Addition:
For planers, the power switch shall not have any locking device to lock it in the “on” position.

Replace the title of Annex I by the following:
Annex I
(normative)

Measurement of noise and vibration emissions

Annex K
(normative)

Battery tools and battery packs

Add the following new subclause:
K.21.18.Z101 Isolation device
Planers with an integral battery shall be equipped with an isolation device to prevent the risk of injury
from mechanical hazards during user maintenance that:
– ensures a reliable disconnection of at least one pole of the battery from the relevant load(s);
– has a reliable mechanical link between the manual control and the disconnecting element(s);
– is equipped with an unambiguous indication of the state of the disconnection device which
corresponds to each position of its manual control (actuator);
– protects against accidental reconnection.
NOTE 1 Examples of methods to achieve this disconnection include removable jumpers, removable batteries or an
electromechanical power switch with a direct mechanical link between the actuator and the contact.
NOTE 2 The risk of accidental reconnection for a power switch is addressed by the requirement of 21.18.1.2. The other
examples in NOTE 1 achieve this by the necessary actions for reconnection.
Compliance is checked by inspection.
4

---------------------- Page: 6 ----------------------

SIST EN 62841-2-14:2015
EN 62841-2-14:2015
Annex L
(normative)

Battery tools and battery packs provided
with mains connection or non-isolated sources

Add the following new subclause:
L.21.18.Z101 Isolation device
Planers with an integral battery shall be equipped with an isolation device to prevent the risk of injury
from mechanical hazards during user maintenance that:
– ensures a reliable disconnection of at least one pole of the battery from the relevant load(s);
– has a reliable mechanical link between the manual control and the disconnecting element(s);
– is equipped with an unambiguous indication of the state of the disconnection device which
corresponds to each position of its manual control (actuator);
– protects against accidental reconnection.
NOTE 1 Examples of methods to achieve this disconnection include removable jumpers, removable batteries or an
electromechanical power switch with a direct mechanical link between the actuator and the contact.
NOTE 2 The risk of accidental reconnection for a power switch is addressed by the requirement of 21.18.1.2. The other
examples in NOTE 1 achieve this by the necessary actions for reconnection.
Compliance is checked by inspection.

Add the following annex:
Annex ZZ
(informative)

Coverage of Essential Requirements of Directive 2006/42/EC
This European Standard has been prepared under a mandate given to CENELEC by the European
Commission and the European Free Trade Association and within its scope the standard covers all
relevant Essential Requirements as given in EU Directive 2006/42/EC (Machinery Directive).
Compliance with this standard provides one means of conformity with the specified essential
requirements of the Directives concerned.
WARNING: Other requirements and other EU Directives may be applicable to the products falling within
the scope of this standard.
5

---------------------- Page: 7 ----------------------

SIST EN 62841-2-14:2015

---------------------- Page: 8 ----------------------

SIST EN 62841-2-14:2015



IEC 62841-2-14

®


Edition 1.0 2015-06




INTERNATIONAL



STANDARD




















Electric motor-operated hand-held tools, transportable tools and lawn and

garden machinery – Safety –

Part 2-14: Particular requirements for hand-held planers


























INTERNATIONAL

ELECTROTECHNICAL


COMMISSION





ICS 25.140.20 ISBN 978-2-8322-2770-1



  Warning! Make sure that you obtained this publication from an authorized distributor.


® Registered trademark of the International Electrotechnical Commission

---------------------- Page: 9 ----------------------

SIST EN 62841-2-14:2015
– 2 – IEC 62841-2-14:2015 © IEC 2015
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references. 5
3 Terms and definitions . 5
4 General requirements . 5
5 General conditions for the tests . 5
6 Radiation, toxicity and similar hazards . 6
7 Classification . 6
8 Marking and instructions . 6
9 Protection against access to live parts . 6
10 Starting . 6
11 Input and current . 7
12 Heating . 7
13 Resistance to heat and fire . 7
14 Moisture resistance . 7
15 Resistance to rusting . 7
16 Overload protection of transformers and associated circuits . 7
17 Endurance . 7
18 Abnormal operation . 7
19 Mechanical hazards . 8
20 Mechanical strength . 10
21 Construction . 10
22 Internal wiring . 11
23 Components . 11
24 Supply connection and external flexible cords . 11
25 Terminals for external conductors . 11
26 Provision for earthing . 11
27 Screws and connections . 11
28 Creepage distances, clearances and distances through insulation . 11
Annexes . 14
Annex I (informative) Measurement of noise and vibration emissions . 14
Annex K (normative) Battery tools and battery packs . 18
Annex L (normative) Battery tools and battery packs provided with mains connection
or non-isolated sources . 19
Bibliography . 20

Figure 101 – Examples of cutting heads with basic dimensions . 12
Figure 102 – Test probe . 13
Figure I.101 – Test set-up for planers . 16
Figure I.102 – Positions of transducers . 17

Table 4 – Required performance levels . 8
Table I.101 – Test conditions . 14

---------------------- Page: 10 ----------------------

SIST EN 62841-2-14:2015
IEC 62841-2-14:2015 © IEC 2015 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

ELECTRIC MOTOR-OPERATED HAND-HELD TOOLS, TRANSPORTABLE
TOOLS AND LAWN AND GARDEN MACHINERY – SAFETY –

Part 2-14: Particular requirements for hand-held planers

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 62841-2-14 has been prepared by IEC technical committee 116:
Safety of motor-operated electric tools.
The text of this standard is based on the following documents:
FDIS Report on voting
116/222/FDIS 116/236/RVD

Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
This Part 2-14 is to be used in conjunction with the first edition of IEC 62841-1 (2014).

---------------------- Page: 11 ----------------------

SIST EN 62841-2-14:2015
– 4 – IEC 62841-2-14:2015 © IEC 2015
This Part 2-14 supplements or modifies the corresponding clauses in IEC 62841-1, so as to
convert it into the IEC standard: Particular requirements for hand-held planers.
Where a particular subclause of Part 1 is not mentioned in this Part 2-14, that subclause
applies as far as relevant. Where this standard states “addition”, “modification” or
“replacement”, the relevant text in Part 1 is to be adapted accordingly.
The following print types are used:
– requirements: in roman type;
– test specifications: in italic type;
– notes: in small roman type.
The terms defined in Clause 3 are printed in bold typeface.
Subclauses, notes and figures which are additional to those in Part 1 are numbered starting
from 101.
A list of all parts of the IEC 62841 series, under the general title: Electric motor-operated
hand-held tools, transportable tools and lawn and garden machinery – Safety, can be found
on the IEC website.
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC website under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
A bilingual version of this publ
...