prEN ISO 27548
(Main)Additive manufacturing of plastics - Environment, health, and safety - Test method for determination of particle and chemical emission rates from desktop material extrusion 3D printer (ISO/DIS 27548:2023)
Additive manufacturing of plastics - Environment, health, and safety - Test method for determination of particle and chemical emission rates from desktop material extrusion 3D printer (ISO/DIS 27548:2023)
This document specifies test methods to determine particle emissions (including ultrafine particles) and specified VOCs (including aldehydes) from Material Extrusion(ME) processes often used in non-industrial environments such as school, homes and office spaces in an Emission Test Chamber (ETC) under specified test conditions. However, these tests may not accurately predict real-world results.
This document describes a conditioning method using an ETC with controlled temperature, humidity, air exchange rate, air velocity, and procedures for monitoring, storage, analysis, calculation, and reporting of emission rates.
This document is intended to cover a Fused Filament Fabrication (FFF) type desktop 3D printer using thermoplastic materials. The primary purpose of this document is to quantify particle and chemical emission rates emitted from a specific ME type desktop 3D printer which is operated using thermoplastic feedstocks.
However, not all possible emissions are covered by this method. Many feedstocks could release hazardous emissions that are not measured by the chemical detectors prescribed in this document. It is the responsibility of the user to understand the material being printed and the potential chemical emissions. An example is PVC feedstocks that could potentially emit chlorinated compounds, which would not be measured by this document.
Additive Fertigung von Kunststoffen - Umwelt, Gesundheit und Sicherheit - Prüfverfahren zur Bestimmung der Partikelemissionsrate und der chemischen Emissionsrate von materialextrusionsbasierten Desktop-3D-Druckern (ISO/DIS 27548:2023)
Fabrication additive de plastiques - Environnement, santé et sécurité - Méthode d'essai pour la détermination des taux d'émission de particules et de produits chimiques des imprimantes 3D de bureau par extrusion de matériau (ISO/DIS 27548:2023)
Aditivna proizvodnja plastičnih izdelkov - Okolje, zdravje in varnost - Preskusna metoda za določanje stopnje emisije delcev in kemikalij iz namiznih 3D tiskalnikov za iztiskanje materiala (ISO/DIS 27548:2023)
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
oSIST prEN ISO 27548:2023
01-junij-2023
[Not translated]
Additive manufacturing of plastics - Environment, health, and safety - Test method for
determination of particle and chemical emission rates from desktop material extrusion 3D
printer (ISO/DIS 27548:2023)
Additive Fertigung von Kunststoffen - Umwelt, Gesundheit und Sicherheit - Prüfverfahren
zur Bestimmung der Partikelemissionsrate und der chemischen Emissionsrate von
materialextrusionsbasierten Desktop-3D-Druckern (ISO/DIS 27548:2023)
Fabrication additive de plastiques - Environnement, santé et sécurité - Méthode d'essai
pour la détermination des taux d'émission de particules et de produits chimiques des
imprimantes 3D de bureau par extrusion de matériau (ISO/DIS 27548:2023)
Ta slovenski standard je istoveten z: prEN ISO 27548
ICS:
13.040.40 Emisije nepremičnih virov Stationary source emissions
13.100 Varnost pri delu. Industrijska Occupational safety.
higiena Industrial hygiene
25.030 3D-tiskanje Additive manufacturing
83.080.01 Polimerni materiali na Plastics in general
splošno
oSIST prEN ISO 27548:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 27548:2023
---------------------- Page: 2 ----------------------
oSIST prEN ISO 27548:2023
DRAFT INTERNATIONAL STANDARD
ISO/DIS 27548
ISO/TC 261 Secretariat: DIN
Voting begins on: Voting terminates on:
2023-05-02 2023-07-25
Additive manufacturing of plastics — Environment, health,
and safety — Test method for determination of particle
and chemical emission rates from desktop material
extrusion 3D printer
ICS: 13.040.30; 25.030; 13.100
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 27548:2023(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2023
---------------------- Page: 3 ----------------------
oSIST prEN ISO 27548:2023
ISO/DIS 27548:2023(E)
DRAFT INTERNATIONAL STANDARD
ISO/DIS 27548
ISO/TC 261 Secretariat: DIN
Voting begins on: Voting terminates on:
Additive manufacturing of plastics — Environment, health,
and safety — Test method for determination of particle
and chemical emission rates from desktop material
extrusion 3D printer
ICS: 13.040.30; 25.030; 13.100
This document is circulated as received from the committee secretariat.
COPYRIGHT PROTECTED DOCUMENT
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
© ISO 2023
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
NOT BE REFERRED TO AS AN INTERNATIONAL
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on STANDARD UNTIL PUBLISHED AS SUCH.
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
IN ADDITION TO THEIR EVALUATION AS
or ISO’s member body in the country of the requester. BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
ISO copyright office
USER PURPOSES, DRAFT INTERNATIONAL
CP 401 • Ch. de Blandonnet 8
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
CH-1214 Vernier, Geneva
POTENTIAL TO BECOME STANDARDS TO
Phone: +41 22 749 01 11
WHICH REFERENCE MAY BE MADE IN
Reference number
Email: copyright@iso.org
NATIONAL REGULATIONS.
Website: www.iso.org ISO/DIS 27548:2023(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
Published in Switzerland
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
ii
© ISO 2023 – All rights reserved
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2023
---------------------- Page: 4 ----------------------
oSIST prEN ISO 27548:2023
ISO/DIS 27548:2023(E)
Contents Page
Foreword .iv
Introduction .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.