Design of fans working in potentially explosive atmospheres

1.1   This European Standard specifies the constructional requirements for fans constructed to Group II G (of explosion groups IIA, IIB and hydrogen) categories 1, 2 and 3, and Group II D categories 2 and 3, intended for use in explosive atmospheres.
NOTE 1   Operation conditions for the different categories of fans used in this European Standard are defined in Clause 4.
NOTE 2   Technical requirements for category 1 D fans are not given in this document. Where explosive dust atmospheres are regularly conveyed, explosion protection measures as described in EN 1127–1 are required if this specific us is needed.
1.2   This European Standard does not apply to group I fans (fans for mining), cooling fans or impellers on rotating electrical machines, cooling fans or impellers on internal combustion engines.
NOTE 1   Requirements for group I fans are given in EN 1710.
NOTE 2   The requirements for electrical parts are covered by references to electrical equipment standards.
1.3   This European Standard specifies requirements for design, construction, testing and marking of complete fan units intended for use in potentially explosive atmospheres in air containing gas, vapour, mist and/or dusts. Such atmospheres may exist inside (the conveyed atmosphere (flammable or not)), outside, or inside and outside of the fan.
1.4   This European Standard is applicable to fans working in ambient atmospheres and with normal atmospheric conditions at the inlet, having
-   absolute pressures ranging from 0,8 bar to 1,1 bar,
-   and temperatures ranging from −20 °C to +60 °C,
-   and maximum volume fraction of 21 % oxygen content,
-   and an aerodynamic energy increase of less than 25 kJ/kg.
NOTE 1   25 kJ/kg is equivalent to 30 kPa at inlet density of 1,2 kg/m3.
This European Standard may also be helpful for the design, construction, testing and marking of fans intended for use in atmospheres outside the validity range stated above or in cases where other material pairings need to be used. In this case, the ignition risk assessment, ignition protection provided, additional testing (if necessary), manufacturer's marking, technical documentation and instructions to the user, should clearly demonstrate and indicate the equipment's suitability for the conditions the fan may encounter.
This European Standard should not apply to integral fans as a part of Diesel engines, vehicles or electric motors.
NOTE 2   Where undated references are used in the body of the standard the latest edition applies.

Konstruktion von Ventilatoren für den Einsatz in explosionsgefährdeten Atmosphären

1.1   Diese Europäische Norm legt die baulichen Anforderungen an Ventilatoren der Gruppe II G (der Explosionsgruppen IIA, IIB und Wasserstoff) Kategorien 1, 2 und 3 und Gruppe II D Kategorien 2 und 3 für die Verwendung in explosionsfähigen Atmosphären fest.
ANMERKUNG 1   Betriebsbedingungen für die verschiedenen Kategorien von Ventilatoren, die von dieser Europäischen Norm erfasst werden, sind in Abschnitt 4 definiert.
ANMERKUNG 2   Technische Anforderungen an Ventilatoren der Kategorie 1 D sind in diesem Dokument nicht enthalten. An Orten, an denen regelmäßig explosionsfähige Staubatmosphären gefördert werden, sind wahrscheinlich Explosionsschutzmaßnahmen gemäß Beschreibung in EN 1127-1 erforderlich.
1.2   Diese Europäische Norm ist nicht anwendbar auf Gruppe-I-Ventilatoren (Ventilatoren für den Bergbau), Kühlgebläse oder Flügelräder für drehende elektrische Maschinen sowie Kühlgebläse oder Flügelräder für Verbrennungsmotoren.
ANMERKUNG 1   Anforderungen an Gruppe-I-Ventilatoren sind in EN 1710 enthalten.
ANMERKUNG 2   Die Anforderungen an elektrische Bauteile werden durch Verweisungen auf Normen für elektrische Geräte behandelt.
1.3   Diese Europäische Norm legt Anforderungen an Konstruktion, Bau, Prüfung und Kennzeichnung kompletter Ventilatoreinheiten fest, die für den Einsatz in explosionsgefährdeten Bereichen, die durch Gase, Dämpfe, Nebel und/oder Staub entstehen, bestimmt sind. Solche Atmosphären können innerhalb (durch die geförderte Atmosphäre (entflammbar oder nicht), außerhalb oder innerhalb und außerhalb des Ventilators existieren.
1.4   Diese Europäische Norm ist anwendbar auf Ventilatoren, die in Umgebungsluft und unter normalen atmosphärischen Bedingungen an der Eintrittsseite betrieben werden, für die gilt:
-   absolute Drücke von 0,8 bar bis 1,1 bar;
-   und Temperaturen zwischen −20 °C und +60 °C;
-   und einem höchstmöglichen Volumenanteil des Sauerstoffgehalts von 21 %;
-   und einem aerodynamischen Energieanstieg von weniger als 25 kJ/kg.
ANMERKUNG 1   25 kJ entsprechen 30 kPa bei einer Eintrittsdichte von 1,2 kg/m3.
Diese Europäische Norm kann auch hilfreich sein für Konstruktion, Bau, Prüfung und Kennzeichnung von Ventilatoren, die für den Einsatz in Atmosphären bestimmt sind, die nicht in den Gültigkeitsbereich dieser Norm fallen, oder in Fällen, in denen andere Werkstoffpaarungen verwendet werden müssen. In diesem Fall sollten die Bewertung des Zündrisikos, der vorgesehene Zündschutz, zusätzliche Prüfung (falls erforderlich), Herstellerkennzeichnung, technische Dokumentation und Anweisungen an den Benutzer klar nachweisen, dass die Ventilatoren für die Bedingungen, auf die sie treffen können, geeignet sind.
Diese Europäische Norm sollte nicht für in Dieselmotoren, Fahrzeugen oder Elektromotoren integrierte Ventilatoren gelten.
ANMERKUNG 2   Undatierte Verweisungen im Hauptteil der Norm beziehen sich auf die jeweils neueste Ausgabe.

Conception des ventilateurs pour les atmosphères explosibles

1.1   La présente Norme européenne spécifie les exigences de construction pour les ventilateurs fabriqués selon le Groupe II G (des groupes d’explosion IIA, IIB et hydrogène) des catégories 1, 2 et 3, et selon le Groupe II D catégories 2 et 3, destinés à être utilisés en atmosphères explosibles.
NOTE 1   Les conditions de fonctionnement des différentes catégories de ventilateurs utilisées dans la présente Norme européenne sont définies à l’Article 4.
NOTE 2   Les exigences techniques pour les ventilateurs de catégorie 1 D ne sont pas données dans le présent document. Lorsque des atmosphères poussiéreuses explosibles sont régulièrement transportées, des mesures de protection contre l’explosion comme celles décrites dans l’EN 1127–1 sont exigées à condition que cet usage spécifique soit nécessaire.
1.2   La présente Norme européenne ne s’applique pas aux ventilateurs du groupe I (ventilateurs pour mines), aux ventilateurs de refroidissement ou roues montées sur des machines électriques tournantes, ventilateurs de refroidissement ou roues montées sur des moteurs fixes à combustion interne.
NOTE 1   Les exigences relatives aux ventilateurs du groupe I sont données dans l’EN 1710.
NOTE 2   Les exigences relatives aux parties électriques sont couvertes par des références à des normes relatives aux équipements électriques.
1.3   La présente Norme européenne définit les exigences relatives à la conception, à la construction, aux essais et au marquage de ventilateurs complets destinés à être utilisés en atmosphères explosibles d’air chargé de gaz, de vapeurs, de brouillards et/ou de poussières. Ces atmosphères peuvent également exister à l’intérieur (de l’atmosphère transportée (inflammable ou non)), à l’extérieur, ou à l’intérieur et à l’extérieur du ventilateur.
1.4   La présente Norme européenne est applicable aux ventilateurs fonctionnant en atmosphères ambiantes et dans des conditions atmosphériques normales au niveau de l’aspiration avec :
-   des pressions absolues de 0,8 bar à 1,1 bar,
-   des températures de −20 °C à +60 °C,
-   une teneur maximale en oxygène de 21 %,
-   une augmentation d’énergie aérodynamique inférieure à 25 kJ/kg.
NOTE 1   25 kJ/kg sont équivalents à 30 kPa pour une masse volumique à l’aspiration de 1,2 kg/m3.
La présente Norme européenne peut également s’avérer utile pour la conception, la construction, les essais et le marquage des ventilateurs destinés à être utilisés dans des atmosphères n’entrant pas dans la plage de validité indiquée ci-dessus ou dans des cas où le recours à d’autres couples de matériaux s’avère nécessaire. Dans ce cas, il convient que l’évaluation du risque d’inflammation, la protection prévue à cet effet, les essais supplémentaires (si nécessaire), le marquage du fabricant, la documentation technique et les instructions destinées à l’utilisateur démontrent et indiquent clairement que l’appareil est adapté aux conditions que le ventilateur peut rencontrer.
Il convient que la présente Norme européenne ne s’applique pas aux ventilateurs intégrés dans les véhicules ni dans les moteurs diesel ou électriques.
NOTE 2   Lorsque des références non datées sont utilisées dans le corps de la norme, la dernière édition de la publication s’applique.

Načrtovanje ventilatorjev za delovanje v potencialno eksplozivnih atmosferah

1.1 Ta evropski standard določa konstrukcijske zahteve za ventilatorje, izdelane za skupino II G (v okviru eksplozijskih skupin II A, II B in vodika) kategorij 1, 2 in 3 ter skupino II D kategorij 2 in 3, ki so namenjeni za uporabo v eksplozivnih atmosferah.
OPOMBA: Pogoji delovanja za različne kategorije ventilatorjev, ki se uporabljajo v tem evropskem standardu, so določeni v točki 4.
1.2 Ta evropski standard se ne uporablja za ventilatorje skupine I (ventilatorji za uporabo v rudarstvu), hladilne ventilatorje ali rotorje pri rotacijskih električnih strojih in hladilne ventilatorje ali rotorje pri motorjih z notranjim izgorevanjem.
OPOMBA 1: Zahteve za ventilatorje skupine I so podane v standardu EN 1710.
OPOMBA 2: Zahteve za električne dele so zajete s sklici na standarde za električno opremo.
1.3 Ta evropski standard določa zahteve za načrtovanje, izdelavo, preskušanje in označevanje zaključenih ventilatorskih enot, namenjenih za uporabo v potencialno eksplozivnih atmosferah plinov, hlapov, meglic in/ali prahu v zraku. Take atmosfere lahko obstajajo znotraj (prevajana tekočina), zunaj ali znotraj in zunaj ventilatorja.
1.4 Ta evropski standard se uporablja za ventilatorje, ki delujejo v okoljskih atmosferah z vrednostmi absolutnega tlaka od 0,8 bara do 1,1 bara, temperaturami od –20 °C do –60 °C, največjim prostorninskim deležem vsebnosti kisika 21 % ter pri vhodnih pogojih (tlak od 0,8 bara do 1,1 bara, temperature od –20 °C do 60 °C) in porastu aerodinamične energije manj kot 25 kJ/kg.
OPOMBA 1: 25 kJ/kg je enako 30 kPa pri vhodni gostoti 1,2 kg/m³.
OPOMBA 2: Ta evropski standard je lahko uporaben tudi pri načrtovanju, izdelavi, preskušanju in označevanju ventilatorjev za uporabo v atmosferah z vrednostmi zunaj zgoraj navedenega validativnega obsega ali v primerih potrebne uporabe drugih vezav materialov. V tem primeru mora biti ustreznost opreme za potencialne pogoje delovanja ventilatorja jasno izražena in prikazana z oceno tveganja za vžig, razpoložljivo zaščito pred vžigom, dodatnim preskušanjem (po potrebi), označbami proizvajalca, tehnično dokumentacijo in navodili za uporabnika.
OPOMBA 3: Ta evropski standard se ne uporablja za ventilatorje, ki so sestavni deli elektromotorjev.
OPOMBA 4: V primeru uporabe nedatiranih sklicevanj v besedilu standarda se uporablja najnovejša izdaja.

General Information

Status
Published
Publication Date
10-Jan-2017
Withdrawal Date
30-Jan-2020
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
11-Jan-2017
Due Date
15-Nov-2016
Completion Date
11-Jan-2017

Relations

Buy Standard

Standard
EN 14986:2017
English language
52 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
prEN 14986:2014
English language
42 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Konstruktion von Ventilatoren für den Einsatz in explosionsgefährdeten BereichenConception des ventilateurs pour les atmosphères explosiblesDesign of fans working in potentially explosive atmospheres29.260.20Electrical apparatus for explosive atmospheres23.120QDSUDYHVentilators. Fans. Air-conditionersICS:Ta slovenski standard je istoveten z:EN 14986:2017SIST EN 14986:2017en,fr,de01-april-2017SIST EN 14986:2017SLOVENSKI
STANDARDSIST EN 14986:20071DGRPHãþD



SIST EN 14986:2017



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 14986
January
t r s y ICS
t uä s t r Supersedes EN
s v { z xã t r r yEnglish Version
Design of fans working in potentially explosive atmospheres Conception des ventilateurs pour les atmosphères explosibles
Konstruktion von Ventilatoren für den Einsatz in explosionsgefährdeten Atmosphären This European Standard was approved by CEN on
u r October
t r s xä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels
9
t r s y CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s v { z xã t r s y ESIST EN 14986:2017



EN 14986:2017 (E) 2 Contents Page European foreword . 4 Introduction . 5 1 Scope . 6 2 Normative references . 7 3 Terms and definitions . 7 4 Requirements for all fans . 8 4.1 Ignition hazard assessment . 8 4.1.1 General . 8 4.1.2 Normal operating conditions . 8 4.1.3 Expected malfunction . 8 4.1.4 Rare malfunction . 8 4.2 Assignment of categories . 8 4.3 Temperatures . 9 4.3.1 General . 9 4.3.2 Maximum surface temperature . 9 4.3.3 Temperature of the conveyed atmosphere (flammable or not) . 10 4.4 Mechanical design criteria . 10 4.4.1
...

SLOVENSKI STANDARD
oSIST prEN 14986:2014
01-april-2014
1DþUWRYDQMHYHQWLODWRUMHY]DGHORYDQMHYSRWHQFLDOQRHNVSOR]LYQLKDWPRVIHUDK
Design of fans working in potentially explosive atmospheres
Konstruktion von Ventilatoren für den Einsatz in explosionsgefährdeten Bereichen
Conception des ventilateurs pour les atmosphères explosibles
Ta slovenski standard je istoveten z: prEN 14986
ICS:
23.120 =UDþQLNL9HWUQLNL.OLPDWVNH Ventilators. Fans. Air-
QDSUDYH conditioners
29.260.20 (OHNWULþQLDSDUDWL]D Electrical apparatus for
HNVSOR]LYQDR]UDþMD explosive atmospheres
oSIST prEN 14986:2014 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 14986:2014

---------------------- Page: 2 ----------------------
oSIST prEN 14986:2014

EUROPEAN STANDARD
DRAFT
prEN 14986
NORME EUROPÉENNE

EUROPÄISCHE NORM

February 2014
ICS 23.120; 29.260.20 Will supersede EN 14986:2007
English Version
Design of fans working in potentially explosive atmospheres
Conception des ventilateurs pour les atmosphères Konstruktion von Ventilatoren für den Einsatz in
explosibles explosionsgefährdeten Bereichen
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 305.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 14986:2014 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 14986:2014
prEN 14986:2014 (E)
Contents
Page
Foreword .4
Introduction .5
1 Scope .6
2 Normative references .6
3 Terms and definitions .7
4 Requirements for all fans .7
4.1 General .7
4.2 Ignition hazard assessment .7
4.2.1 General .7
4.2.2 Normal operating conditions .8
4.2.3 Expected malfunction .8
4.2.4 Rare malfunction.
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.