EN 14870-1:2004

Petroleum and natural gas industries - Induction bends, fittings and flanges for pipeline transportation systems - Part 1: Induction bends (ISO 15590-1:2001 modified)

This part of prEN 14870 specifies the technical delivery conditions for bends made by the induction bending process for use in pipeline transportation systems for the petroleum and natural gas industries as defined in ISO 13623.
This part of prEN 14870 is applicable to induction bends made from seamless and welded pipe of unalloyed or low-alloy steels.
This part of prEN 14870 specifies three classes of induction bend corresponding to increasing quality requirements in accordance with the technical delivery conditions of ISO 3183 for pipe as indicated in Table 1 (see also ISO 3183-3:1999, Introduction).
Table 1 - Induction bend class and corresponding pipe standard
Induction bend class   Corresponding pipe standard
Class A                                  ISO 3183-1
Class B                                  ISO 3183-2
Class C                                  ISO 3183-3
This part of prEN 14870 is not applicable to the selection of the induction bend class.
This part of prEN 14870 is not applicable to pipeline bends made by other manufacturing processes.
On-land supply systems used by the gas supply industry are excluded from the scope of this standard.

Erdöl- und Erdgasindustrie - Im Induktionsverfahren gefertigte Rohrbögen, Fittings und Flansche für Rohrleitungs-Transportsysteme - Teil 1: Im Induktionsverfahren gefertigte Rohrbögen (ISO 15590-1:2001 modifiziert)

Dieser Teil der prEN 14870 (WI 00012096) (ISO 15590-1:2001 modifiziert) legt die technischen Lieferbe-dingungen für im Induktionsverfahren gefertigte Rohrbögen für die Verwendung in Rohrleitungtransportsystemen für die Erdöl- und Erdgasindustrie nach den Festlegungen in ISO 13623 fest.
Dieser Teil der prEN 14870 (WI 00012096) (ISO 15590-1:2001 modifiziert) gilt für im Induktionsverfahren aus nahtlosen und geschweißten Rohren aus unlegiertem oder niedrig legiertem Stahl gefertigte Rohrbögen.
Dieser Teil der prEN 14870 (WI 00012096) (ISO 15590-1:2001 modifiziert) legt für diese Rohrbögen drei Anforderungsklassen mit steigenden Qualitätsanforderungen nach den technischen Lieferbedingungen in ISO 3183 für Rohr fest, wie in Tabelle 1 angegeben (siehe auch ISO 3183-3:1999, Einleitung).
Tabelle 1 - Klasseneinteilung der im Induktionsverfahren
gefertigten Rohrbögen und entsprechenden Rohr-Norm
Induktivrohrbogen
Anforderungsklasse   Entspricht
der Rohr-Norm
   Anforderungsklasse A   ISO 3183-1
   Anforderungsklasse B   ISO 3183-2
   Anforderungsklasse C   ISO 3183-3
Dieser Teil der prEN 14870 (WI 00012096) (ISO 15590-1:2001 modifiziert) gilt nicht für die Auswahl der jeweiligen Anforderungsklasse der Rohrbögen.
Dieser Teil der prEN 14870 (WI 00012096) (ISO 15590-1:2001 modifiziert) gilt nicht für Rohrleitungsbogen, die nach
anderen Verfahren gefertigt werden.
Rohrleitungstransportsysteme für die Gasversorgung an Land fallen nicht in den Anwendungsbereich dieser Norm.

Industries du pétrole et du gaz naturel - Coudes d'induction, raccords et brides pour systèmes de transport par conduites -Partie 1: Coudes d'induction (ISO 15590-1:2001 modifiée)

Petroleum and natural gas industries - Induction bends, fittings and flanges for pipeline transportation systems - Part 1: Induction bends (ISO 15590-1:2001 modified)

General Information

• Status: Withdrawn
• Publication Date: 26-Oct-2004
• Withdrawal Date: 28-Jun-2011
• ICS: 23.040.40 - Metal fittings
• ICS: 23.040.60 - Flanges, couplings and joints
• ICS: 75.200 - Petroleum products and natural gas handling equipment
• Technical Committee: CEN/TC 12 - Materials, equipment and offshore structures for petroleum and natural gas industries
• Drafting Committee: CEN/TC 12 - Materials, equipment and offshore structures for petroleum and natural gas industries
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Start Date: 29-Jun-2011
• Completion Date: 29-Jun-2011
• Ref Project: SIST EN 14870-1:2005 - Petroleum and natural gas industries - Induction bends, fittings and flanges for pipeline transportation systems - Part 1: Induction bends (ISO 15590-1:2001 modified)

Relations

• Replaced By: EN 14870-1:2011 - Petroleum and natural gas industries - Induction bends, fittings and flanges for pipeline transportation systems - Part 1: Induction bends (ISO 15590-1:2009 modified)
• Effective Date: 22-Dec-2008

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Petroleum and natural gas industries - Induction bends, fittings and flanges for pipeline transportation systems - Part 1: Induction bends (ISO 15590-1:2001 modified)Erdöl- und Erdgasindustrie - Im Induktionsverfahren gefertigte Rohrbögen, Fittings und Flansche für Rohrleitungs-Transportsysteme - Teil 1: Im Induktionsverfahren gefertigte Rohrbögen (ISO 15590-1:2001 modifiziert)Industries du pétrole et du gaz naturel - Coudes d'induction, raccords et brides pour systemes de transport par conduites -Partie 1: Coudes d'induction (ISO 15590-1:2001 modifiée)Petroleum and natural gas industries - Induction bends, fittings and flanges for pipeline transportation systems - Part 1: Induction bends (ISO 15590-1:2001 modified)83.140.30Cevi, fitingi in ventili iz polimernih materialovPlastics pipes, fittings and valves75.200Petroleum products and natural gas handling equipmentICS:Ta slovenski standard je istoveten z:EN 14870-1:2004SIST EN 14870-1:2005en01-marec-2005SIST EN 14870-1:2005SLOVENSKI
STANDARD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 14870-1October 2004ICS 75.200; 23.040.40; 23.040.60English versionPetroleum and natural gas industries - Induction bends, fittingsand flanges for pipeline transportation systems - Part 1:Induction bends (ISO 15590-1:2001 modified)Industries du pétrole et du gaz naturel - Coudes d'induction,raccords et brides pour systèmes de transport parconduites -Partie 1: Coudes d'induction (ISO 15590-1:2001modifiée)Erdöl- und Erdgasindustrie - Im Induktionsverfahrengefertigte Rohrbögen, Fittings und Flansche fürRohrleitungstransportsysteme - Teil 1: ImInduktionsverfahren gefertigte Rohrbögen (ISO 15590-1:2001 modifiziert)This European Standard was approved by CEN on 15 July 2004.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2004 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 14870-1:2004: ESIST EN 14870-1:2005

Normative references to international publications with their European publication correspondence.30 Bibliography.31
ISO 15590-1:2001, developed within ISO/TC 67 SC 2, has been adopted as EN 14870-1:2004 (ISO 15590-1 : 2001 modified).
The scope of ISO/TC 67/SC 2 is pipeline transportation systems for the petroleum and natural gas industries without exclusions. However in CEN, the scopes of CEN/TC 12 and CEN/TC 234 overlapped until 1995.This scope overlap caused problems for the parallel procedure for the above-mentioned items. The conflict in scope was resolved when both the CEN/Technical Committees and the CEN/BT took the following resolution:
Resolution BT 38/1995: Subject: Revised scope of CEN/TC 12
“BT endorses the conclusions of the coordination meeting between CEN/TC 12 “Materials, equipment and offshore structures for petroleum and natural gas industries” and CEN/TC 234 “Gas supply” and modifies the CEN/TC 12 scope, to read:
“Standardization of the materials, equipment and offshore structures used in drilling, production, refining and the transport by pipelines of petroleum and natural gas, excluding on-land supply systems used by the gas supply industry and those aspects of offshore structures covered by IMO requirement (ISO/TC 8). The standardization is to be achieved wherever possible by the adoption of ISO Standards.”
Resulting from Resolution BT 38/1995, "gas supply on land" has been excluded from the scope of ISO 15590-1 : 2001 for the European adoption by CEN/TC 12.
2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 148, Steel – Charpy impact test (V-notch). EN ISO 377, Steel and steel products - Location and preparation of samples and test pieces for mechanical testing (ISO 377:1997) ISO 783, Metallic materials – Tensile testing at elevated temperature. EN ISO 2566-1, Steel – Conversion of elongation values – Part 1 : Carbon and low alloy steels (ISO 2566-1:1984). ISO 3183-1, Petroleum and natural gas industries – Steel pipe for pipelines – Technical delivery conditions – Part 1 : Pipes of requirement class A. ISO 3183-2, Petroleum and natural gas industries – Steel pipe for pipelines – Technical delivery conditions – Part 2 : Pipes of requirement class B. ISO 3183-3:1999, Petroleum and natural gas industries – Steel pipe for pipelines – Technical delivery conditions – Part 3 : Pipes of requirement class C. EN ISO 6507-1, Metallic materials – Vickers hardness test – Part 1 : Test method (ISO 6507-1:1997) SIST EN 14870-1:2005
...