EN ISO 14113:2008
(Main)Gas welding equipment - Rubber and plastics hose and hose assemblies for use with industrial gases up to 450 bar (45 MPa) (ISO 14113:2007)
Gas welding equipment - Rubber and plastics hose and hose assemblies for use with industrial gases up to 450 bar (45 MPa) (ISO 14113:2007)
ISO 14113:2007 specifies requirements for rubber and plastics hose and hose assemblies for use with compressed, liquefied and dissolved gases up to a maximum working pressure of 45 MPa (450 bar), within the ambient temperature range of - 20 °C to + 60 °C.
ISO 14113:2007 applies to hose assemblies used to connect industrial gas cylinders to manifolds or bundles prior to any pressure reduction stage.
ISO 14113:2007 does not cover rubber or thermoplastic hoses for welding, cutting and allied processes (see ISO 3821 and ISO 12170).
ISO 14113:2007 does not apply to refrigerated liquefied gases or to liquefied petroleum gases (LPG).
Gasschweißgeräte - Gummi- und Kunststoffschläuche und Schlauchleitungen für Industriegase bis zu einem Druck von 450 bar (45 MPa) (ISO 14113:2007)
In dieser Norm sind Anforderungen für Gummi und Kunststoffschläuche und Schlau¬chleitungen für Druck oder Flüssiggase bis zu einem maximalen Betriebsdruck von 450 bar (45 MPa) im Bereich der Umgebungstemperatur zwischen 20 C bis 60 °C festgelegt.
Diese Norm ist anwendbar für Hochdruckschlauchleitungen, welche verwendet werden, um industrielle Gas-flaschen oder Bündel ohne Hauptstellendruckregler zu Batterien zusammenzuschließen.
Diese Norm gilt nicht für thermoplastische Schläuche für Schweißen, Schneiden und verwandte Prozesse (siehe ISO 3821 und ISO 12170).
Diese Norm gilt nicht für tiefkalte ver¬flüssigte Gase oder LPG (Flüssiggas).
Matériel de soudage aux gaz - Tuyaux souples et flexibles en caoutchouc et en plastique pour des gaz industriels jusqu'à 450 bar (45 MPa) (ISO 14113:2007)
L'ISO 14113:2007 spécifie les exigences relatives aux tuyaux souples et flexibles en caoutchouc et en plastique devant être utilisés avec des gaz comprimés, liquéfiés ou dissous jusqu'à une pression maximale de service de 450 bar (45 MPa) à des températures ambiantes comprises entre ‑20 °C et 60 °C.
Elle s'applique aux flexibles utilisés pour relier les bouteilles de gaz industriels aux collecteurs et aux cadres de bouteilles avant toute opération de détente.
Elle ne couvre pas les tuyaux souples en caoutchouc et en matière thermoplastique pour le soudage, le coupage et les techniques connexes (voir l'ISO 3821 et l'ISO 12170).
Elle ne s'applique pas aux gaz liquides cryogéniques ou aux gaz de pétrole liquéfiés (GPL).
Oprema za plamensko varjenje - Cevi in napeljave iz gume in umetnih snovi za tehnične pline do tlaka 450 bar (45 MPa) (ISO 14113:2007)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-april-2009
2SUHPD]DSODPHQVNRYDUMHQMH&HYLLQQDSHOMDYHL]JXPHLQXPHWQLKVQRYL]D
WHKQLþQHSOLQHGRWODNDEDU 03D ,62
Gas welding equipment - Rubber and plastics hose and hose assemblies for use with
industrial gases up to 450 bar (45 MPa) (ISO 14113:2007)
Gasschweißgeräte - Gummi- und Kunststoffschläuche und Schlauchleitungen für
Industriegase bis zu einem Druck von 450 bar (45 MPa) (ISO 14113:2007)
Matériel de soudage aux gaz - Tuyaux souples et flexibles en caoutchouc et en plastique
pour des gaz industriels jusqu'à 450 bar (45 MPa) (ISO 14113:2007)
Ta slovenski standard je istoveten z: EN ISO 14113:2008
ICS:
25.160.30 Varilna oprema Welding equipment
83.140.40 Gumene cevi Hoses
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 14113
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2008
ICS 83.140.40; 25.160.30 Supersedes EN ISO 14113:1997
English Version
Gas welding equipment - Rubber and plastics hose and hose
assemblies for use with industrial gases up to 450 bar (45 MPa)
(ISO 14113:2007)
Matériel de soudage aux gaz - Tuyaux souples et flexibles Gasschweißgeräte - Gummi- und Kunststoffschläuche und
en caoutchouc et en plastique pour des gaz industriels Schlauchleitungen für Industriegase bis zu einem Druck
jusqu'à 450 bar (45 MPa) (ISO 14113:2007) von 450 bar (45 MPa) (ISO 14113:2007)
This European Standard was approved by CEN on 9 August 2008.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 14113:2008: E
worldwide for CEN national Members.
Contents Page
Foreword.3
Foreword
The text of ISO 14113:2007 has been prepared by Technical Committee ISO/TC 44 “Welding and allied
processes” of the International Organization for Standardization (ISO) and has been taken over as EN ISO
14113:2008 by Technical Committee CEN/TC 121 “Welding” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by April 2009, and conflicting national standards shall be withdrawn at the
latest by April 2009.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 14113:1997.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 14113:2007 has been approved by CEN as a EN ISO 14113:2008 without any modification.
INTERNATIONAL ISO
STANDARD 14113
Second edition
2007-11-01
Gas welding equipment — Rubber and
plastics hose and hose assemblies for
use with industrial gases up to 450 bar
(45 MPa)
Matériel de soudage aux gaz — Tuyaux souples et flexibles en
caoutchouc et en plastique pour des gaz industriels jusqu'à 450 bar
(45 MPa)
Reference number
ISO 14113:2007(E)
©
ISO 2007
ISO 14113:2007(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2007
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2007 – All rights reserved
ISO 14113:2007(E)
Contents Page
Foreword. iv
1 Scope. 1
2 Normative references. 1
3 Terms and definitions. 2
4 Construction. 3
5 Dimensions and tolerances . 4
6 Physical properties of lining and cover — Type tests. 5
7 Performance requirements — Type tests. 5
8 Performance requirements — Production tests. 7
9 Marking. 7
10 Packaging. 8
11 Instructions . 8
Annex A (normative) Acetylene decomposition test for hose assemblies used in high pressure
acetylene installations. 9
Annex B (normative) Oxygen pressure surge test . 10
Annex C (normative) Oxygen system installation considerations. 12
Bibliography . 13
ISO 14113:2007(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 14113 was prepared by Technical Committee ISO/TC 44, Welding and allied processes, Subcommittee
SC 8, Equipment for gas welding, cutting and allied processes.
This second edition cancels and replaces the first edition (ISO 14113:1997), which has been technically
revised.
Requests for official interpretations of any aspect of this International Standard should be directed to the
Secretariat of ISO/TC 44/SC 8 via your national standards body, a complete listing of which can be found at
www.iso.org.
iv © ISO 2007 – All rights reserved
INTERNATIONAL STANDARD ISO 14113:2007(E)
Gas welding equipment — Rubber and plastics hose and hose
assemblies for use with industrial gases up to 450 bar (45 MPa)
1 Scope
This International Standard specifies requirements for rubber and plastics hose and hose assemblies for use
with compressed, liquefied and dissolved gases up to a maximum working pressure of 45 MPa (450 bar),
within the ambient temperature range of −20 °C to +60 °C.
This International Standard applies to hose assemblies used to connect industrial gas cylinders to manifolds
or bundles prior to any pressure reduction stage.
This International Standard does not cover rubber or thermoplastic hoses for welding, cutting and allied
processes (see ISO 3821 and ISO 12170).
This International Standard does not apply to refrigerated liquefied gases or to liquefied petroleum gases
(LPG).
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 105-A02:1993, Textiles — Tests for colour fastness — Part A02: Grey scale for assessing change in
colour
ISO 1307:2006, Rubber and plastics hoses — Hose sizes, minimum and maximum inside diameters, and
tolerances on cut-to-length hoses
ISO 1402, Rubber and plastics hoses and hose assemblies — Hydrostatic testing
ISO 1746:1998, Rubber or plastics hoses and tubing — Bending tests
ISO 1817, Rubber, vulcanized — Determination of the effect of liquids
ISO 4080:1991, Rubber and plastic hoses and hose assemblies — Determination of permeability to gas
ISO 4671, Rubber and plastics hoses and hose assemblies — Methods of measurement of the dimensions of
hoses and the lengths of hose assemblies
ISO 4672:1997, Rubber and plastics hoses — Sub-ambient temperature flexibility tests
ISO 7326:2006, Rubber and plastics hoses — Assessment of ozone resistance under static conditions
ISO 8031, Rubber and plastics hoses and hose assemblies — Determination of electrical properties
ISO 8033:2006, Rubber and plastics hoses — Determination of adhesion between components
ISO 14113:2007(E)
ISO 9539, Materials for equipment used in gas welding, cutting and allied processes
ISO 11114-3, Transportable gas cylinders — Compatibility of cylinder and valve materials with gas
contents — Part 3: Autogenous ignition test in oxygen atmosphere
ISO 11758:1995, Rubber and plastics hoses — Exposure to a xenon arc lamp — Determination of changes in
colour and appearance
ISO 15296, Gas welding equipment — Vocabulary — Terms used for gas welding equipment
ISO 23529, Rubber — General procedures for preparing and conditioning test pieces for physical test
methods
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 15296 and the following apply.
3.1
autogenous ignition temperature
temperature at which ignition of a sample occurs when subjected to oxygen pressure and heating, and in the
absence of a source of ignition other than the applied temperature
NOTE The autogenous ignition temperature depends on the sample preparation, test apparatus and test p
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.