Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 13: Upset (resistance butt) and flash welding (ISO 15614-13:2021)

This document specifies tests for the qualification of welding procedure specifications applicable to upset (resistance butt) welding and flash welding of metallic materials, e.g. with solid, tubular, flat or circular cross-section. Its basic principles can also be applied to other resistance welding processes when this is stated in the specification.
This document defines the conditions for carrying out tests and the limits of validity of a qualified welding procedure for all the practical welding operations that it covers.
It covers the following resistance welding processes, as defined in ISO 4063:
—    24 flash welding, using direct current or alternating current with various movement sequences, constant flashing and pulsed flashing;
—    25 resistance upset welding, using direct current or alternating current with various pressure sequences.

Anforderung und Qualifizierung von Schweißverfahren für metallische Werkstoffe - Schweißverfahrensprüfung - Teil 13: Pressstumpf- und Abbrennstumpfschweißen (ISO 15614-13:2021)

Dieses Dokument legt die Prüfungen für die Qualifizierung von Schweißanweisungen für das Pressstumpf- und das Abbrennstumpfschweißen von metallischen Werkstoffen, z. B. bei vollen, rohrförmigen, flachen oder runden Querschnitten, fest. Ihre Grundprinzipien können auch für andere Widerstandsschweißprozesse angewendet werden, wenn dies in der Spezifikation ausgeführt wird.
Dieses Dokument legt die Bedingungen für die Ausführung der Prüfungen und die Grenzen der Gültigkeit eines qualifizierten Schweißverfahrens für alle in der Praxis angewendeten Schweißverfahren fest, die es abdeckt.
Es deckt die folgenden Widerstandsschweißprozesse ab, die in ISO 4063 festgelegt sind:
—   24 – Abbrennstumpfschweißen bei Verwendung von Gleich- oder Wechselstrom mit veränderlichem Bewegungsablauf, konstantem Abbrennen und gepulstem Abbrennen;
—   25 – Pressstumpfschweißen bei Anwendung von Gleich- oder Wechselstrom mit veränderlichem Druck¬verlauf.

Descriptif et qualification d'un mode opératoire de soudage pour les matériaux métalliques - Épreuve de qualification d'un mode opératoire de soudage - Partie 13: Soudage en bout par résistance pure et soudage par étincelage (ISO 15614-13:2021)

Le présent document spécifie des épreuves pour qualifier un descriptif de mode opératoire de soudage. Elle est applicable au soudage en bout par résistance pure et au soudage par étincelage des matériaux métalliques, par exemple des sections droites pleines ou tubulaires, plates ou circulaires. Les principes de base du présent document peuvent être appliqués à d'autres procédés de soudage par résistance lorsque cela est indiqué dans la spécification.
Le présent document définit les conditions d'exécution des épreuves de qualification et les limites de validité d'un mode opératoire qualifié, pour toutes les opérations pratiques de soudage qu'elle couvre.
Il couvre les procédés de soudage par résistance suivants, tels que définis dans l’ISO 4063:
—    24 soudage par étincelage en courant continu ou en courant alternatif avec diverses séquences de mouvement, étincelage continu et étincelage intermittent;
—    25 soudage en bout par résistance pure, en courant continu ou en courant alternatif avec diverses séquences d'effort.

Popis in kvalifikacija varilnih postopkov za kovinske materiale - Preskus varilnega postopka - 13. del: Uporovno sočelno in obžigalno varjenje (ISO 15614-13:2021)

Ta dokument določa preskuse za kvalifikacijo popisov varilnih postopkov, ki se uporabljajo za uporovno sočelno in obžigalno varjenje kovinskih materialov, npr. z masivnim, cevnim, ravnim ali krožnim prerezom. Osnovna načela je mogoče uporabiti tudi za druge postopke uporovnega varjenja, kadar je to navedeno v specifikaciji. Ta dokument določa pogoje za izvajanje preskusov in roke veljavnosti kvalificiranih varilnih postopkov za vse praktične varilne postopke, ki so v njem zajeti. Zajema naslednje postopke uporovnega varjenja iz standarda ISO 4063: – 24 obžigalno varjenje pri enosmernem ali izmeničnem toku z različnimi zaporedji premikov, stalnim in občasnim obžiganjem; – 25 uporovno sočelno varjenje pri enosmernem ali izmeničnem toku z različnimi tlačnimi zaporedji.

General Information

Status
Withdrawn
Publication Date
30-Nov-2021
Withdrawal Date
21-Nov-2023
Current Stage

Relations

Buy Standard

Standard
EN ISO 15614-13:2022
English language
23 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-marec-2022
Nadomešča:
SIST EN ISO 15614-13:2012
Popis in kvalifikacija varilnih postopkov za kovinske materiale - Preskus varilnega
postopka - 13. del: Uporovno sočelno in obžigalno varjenje (ISO 15614-13:2021)
Specification and qualification of welding procedures for metallic materials - Welding
procedure test - Part 13: Upset (resistance butt) and flash welding (ISO 15614-13:2021)
Anforderung und Qualifizierung von Schweißverfahren für metallische Werkstoffe -
Schweißverfahrensprüfung - Teil 13: Pressstumpf- und Abbrennstumpfschweißen (ISO
15614-13:2021)
Descriptif et qualification d'un mode opératoire de soudage pour les matériaux
métalliques - Épreuve de qualification d'un mode opératoire de soudage - Partie 13:
Soudage en bout par résistance pure et soudage par étincelage (ISO 15614-13:2021)
Ta slovenski standard je istoveten z: EN ISO 15614-13:2021
ICS:
25.160.10 Varilni postopki in varjenje Welding processes
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 15614-13
EUROPEAN STANDARD
NORME EUROPÉENNE
December 2021
EUROPÄISCHE NORM
ICS 25.160.10 Supersedes EN ISO 15614-13:2012
English Version
Specification and qualification of welding procedures for
metallic materials - Welding procedure test - Part 13:
Upset (resistance butt) and flash welding (ISO 15614-
13:2021)
Descriptif et qualification d'un mode opératoire de Anforderung und Qualifizierung von Schweißverfahren
soudage pour les matériaux métalliques - Épreuve de für metallische Werkstoffe -
qualification d'un mode opératoire de soudage - Partie Schweißverfahrensprüfung - Teil 13: Pressstumpf- und
13: Soudage en bout par résistance pure et soudage par Abbrennstumpfschweißen (ISO 15614-13:2021)
étincelage (ISO 15614-13:2021)
This European Standard was approved by CEN on 5 November 2021.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15614-13:2021 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 15614-13:2021) has been prepared by Technical Committee ISO/TC 44
"Welding and allied processes" in collaboration with Technical Committee CEN/TC 121 “Welding and
allied processes” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by June 2022, and conflicting national standards shall be
withdrawn at the latest by June 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 15614-13:2012.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 15614-13:2021 has been approved by CEN as EN ISO 15614-13:2021 without any
modification.
INTERNATIONAL ISO
STANDARD 15614-13
Third edition
2021-11
Specification and qualification of
welding procedures for metallic
materials — Welding procedure test —
Part 13:
Upset (resistance butt) and flash
welding
Descriptif et qualification d'un mode opératoire de soudage pour
les matériaux métalliques — Épreuve de qualification d'un mode
opératoire de soudage —
Partie 13: Soudage en bout par résistance pure et soudage par
étincelage
Reference number
ISO 15614-13:2021(E)
ISO 15614-13:2021(E)
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 15614-13:2021(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope .1
2 Normative references .1
3 Terms and definitions . 2
4 Preliminary welding procedure specification . 2
4.1 General . 2
4.2 Welding procedure test . 2
5 Test pieces and test specimens .3
5.1 General . 3
5.2 Shape and dimensions of test specimens. 3
5.2.1 General . 3
5.2.2 Tensile test specimen . 4
5.2.3 Bend test specimen . 4
5.2.4 Cupping test specimen . 4
5.2.5 Hardness test specimen . 4
5.2.6 Bend test specimen using thin sheets . 5
5.3 Welding of components, test pieces or test specimens. 5
6 Testing and examination.5
6.1 Extent of testing . 5
6.2 Non-destructive testing (NDT) . 5
6.2.1 General . 5
6.2.2 Visual test . 5
6.2.3 Penetrant test . 5
6.2.4 Magnetic particle test . 5
6.2.5 Eddy current test . 5
6.2.6 Ultrasonic test . 5
6.3 Destructive tests . 6
6.3.1 Tensile test . 6
6.3.2 Three-point bend test . 6
6.3.3 Cupping test . 6
6.3.4 Bend test . 6
6.4 Macrosection . 6
6.5 Hardness distribution . 6
6.6 Re-testing . 6
7 Range of qualification .6
7.1 General . 6
7.2 Related to the manufacturer . 7
7.3 Related to the parent metal . 7
7.4 Welding procedures . 7
7.4.1 Welding process .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.