District heating pipes - Bonded single pipe systems for directly buried hot water networks - Factory made fitting assemblies of steel service pipes, polyurethane thermal insulation and a casing of polyethylene

This document specifies requirements and test methods for factory made thermally insulated bonded fitting assemblies for hot water networks in accordance with EN 13941 1, comprising a steel service fitting, rigid polyurethane foam thermal insulation and a casing of polyethylene.
The fitting assembly could also include the following additional elements: measuring wires, spacers and diffusion barriers.
This document covers the following fitting assemblies: bend, tee, reducer, single use compensator and anchor.
This document applies to fitting assemblies with a minimum design pressure of 1,6 MPa (overpressure).

Fernwärmerohre - Einzelrohr-Verbundsysteme für direkt erdverlegte Fernwärmenetze - Werkmäßig gefertigte Verbundformstücke, bestehend aus Stahl-Mediumrohren, einer Wärmedämmung aus Polyurethan und einer Ummantelung aus Polyethylen

Dieses Dokument legt die Anforderungen und Prüfverfahren für werkmäßig gefertigte, wärmegedämmte Verbundformstücke für Fernwärmenetze in Übereinstimmung mit EN 13941-1 fest, die aus einer Stahlarmatur, einer Polyurethan-Hartschaumstoffwärmedämmung und einem Polyethylenmantel bestehen.
Das Verbundformstück könnte darüber hinaus die folgenden zusätzlichen Bauteile umfassen: Messdrähte, Abstandhalter und Diffusionsbarrieren.
Dieses Dokument behandelt folgende Verbundformstücke: Bogen, T-Stück, Reduzierstück, Einmalkompen-sator und Festpunktelement.
Dieses Dokument gilt für Verbundformstücke mit einem Mindestauslegungsdruck von 1,6 MPa (Überdruck).

Tuyaux de chauffage urbain - Systèmes bloqués monotubes pour des réseaux d'eau chaude enterrés directement - Assemblages de raccords manufacturés pour tubes de service en acier, isolation thermique en polyuréthane et tube de protection en polyéthylène

Le présent document spécifie les exigences et les méthodes d’essai applicables aux assemblages de raccords bloqués manufacturés isolés thermiquement pour les réseaux d'eau chaude, conformes à l’EN 13941-1, comprenant un raccord de service en acier, une isolation thermique en mousse rigide de polyuréthane et un tube de protection en polyéthylène.
L’assemblage de raccord peut également comprendre les éléments supplémentaires suivants : câbles de mesure, entretoises et barrières anti-diffusion.
Le présent document couvre les assemblages de raccords suivants : coude, té, réducteur, compensateur à usage unique et pièce d’ancrage.
Le présent document s’applique aux assemblages de raccords de pression minimale de calcul de 1,6 MPa (surpression).

Cevi za daljinsko ogrevanje - Poviti enocevni sistemi za neposredno vkopana vročevodna omrežja - Tovarniško izdelana armatura iz jeklenih delovnih cevi, obdanih s poliuretansko toplotno izolacijo in zaščitnim plaščem iz polietilena

Ta dokument določa zahteve in preskusne metode za tovarniško izdelane toplotno izolirane sestave fitingov za vročevodna omrežja v skladu s standardom prEN 13941-1, ki so sestavljeni iz jeklenih fitingov, trde poliuretanske izolacijske pene in polietilenskega plašča. Sestav fitingov lahko vključuje tudi naslednje dodatne elemente: merilne žice, distančnike in difuzijske pregrade. Ta dokument zajema naslednje sestave fitingov: kolena, T-komade, reducirne priključke, kompenzatorje za enkratno uporabo in sidra. Ta dokument se uporablja za sestave fitingov z minimalnim predvidenim tlakom 16 barov (nadtlak).

General Information

Status
Published
Publication Date
15-Oct-2019
Withdrawal Date
29-Apr-2020
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
16-Oct-2019
Due Date
24-Nov-2019
Completion Date
16-Oct-2019

Relations

Buy Standard

Standard
EN 448:2020
English language
31 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-januar-2020
Nadomešča:
SIST EN 448:2016
Cevi za daljinsko ogrevanje - Poviti enocevni sistemi za neposredno vkopana
vročevodna omrežja - Tovarniško izdelana armatura iz jeklenih delovnih cevi,
obdanih s poliuretansko toplotno izolacijo in zaščitnim plaščem iz polietilena
District heating pipes - Bonded single pipe systems for directly buried hot water networks
- Factory made fitting assemblies of steel service pipes, polyurethane thermal insulation
and a casing of polyethylene
Fernwärmerohre - Werkmäßig gedämmte Verbundmantelrohrsysteme für direkt
erdverlegte Fernwärmenetze - Verbundformstücke, bestehend aus Stahl-Mediumrohr,
Polyurethan-Wärmedämmung und Außenmantel aus Polyethylen
Tuyaux de chauffage urbain - Systèmes bloqués monotubes pour des réseaux d'eau
chaude enterrés directement - Assemblages de raccords manufacturés pour tubes de
service en acier, isolation thermique en polyuréthane et tube de protection en
polyéthylène
Ta slovenski standard je istoveten z: EN 448:2019
ICS:
23.040.07 Cevovodi za daljinsko Pipeline and its parts for
ogrevanje in njihovi deli district heat
23.040.40 Kovinski fitingi Metal fittings
91.140.65 Oprema za ogrevanje vode Water heating equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN 448
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2019
EUROPÄISCHE NORM
ICS 23.040.07; 23.040.40 Supersedes EN 448:2015
English Version
District heating pipes - Bonded single pipe systems for
directly buried hot water networks - Factory made fitting
assemblies of steel service pipes, polyurethane thermal
insulation and a casing of polyethylene
Tuyaux de chauffage urbain - Systèmes bloqués Fernwärmerohre - Verbund-Rohrsysteme mit einem
monotubes pour des réseaux d'eau chaude enterrés Mediumrohr für direkt erdverlegte Fernwärmenetze -
directement - Assemblages de raccords manufacturés Werkmäßig hergestellte Formstücke bestehend aus
pour tubes de service en acier, isolation thermique en Stahl-Mediumrohren, einer Wärmedämmung aus
polyuréthane et tube de protection en polyéthylène Polyurethan und einer Ummantelung aus Polyethylen
This European Standard was approved by CEN on 12 August 2019.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 448:2019 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 7
4 Requirements . 7
5 Test methods . 17
6 Marking . 21
Annex A (informative) Guidelines for inspection and testing . 23
Annex B (informative) Procedures for casing welding . 26
Annex C (informative) Waste treatment and recycling . 30
Bibliography . 31
European foreword
This document (EN 448:2019) has been prepared by Technical Committee CEN/TC 107 “Prefabricated
district heating and district cooling pipe system”, the secretariat of which is held by DS.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by April 2020, and conflicting national standards shall be withdrawn at
the latest by April 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 448:2015.
In comparison with the previous edition, the main changes in EN 448:2019 are:
— editorial changes to the new structure of standards prepared by the Technical Committee
CEN/TC 107.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North Macedonia,
Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Introduction
EN 448 has been aligned with EN 488 and other relevant European Standards.
Other standards from CEN/TC 107 are:
— EN 253, District heating pipes — Bonded single pipe systems for directly buried hot water networks —
Factory made pipe assembly of steel service pipe, polyurethane thermal insulation and a casing of
polyethylene;
— EN 488, District heating pipes — Bonded single pipe systems for directly buried hot water networks —
Factory made steel valve assembly for steel service pipes, polyurethane thermal insulation and a casing of
polyethylene ;
— EN 489-1, District heating pipes — Bonded single and twin pipe systems for buried hot water networks —
Part 1: Joint casing assemblies and thermal insulation for hot water networks in accordance with
EN 13941-1;
— EN 13941-1, District heating pipes — Design and installation of thermal insulated bonded single and twin
pipe systems for directly buried hot water networks — Part 1: Design;
— EN 13941-2, District heating pipes — Design and installation of thermal insulated bonded single and twin
pipe systems for directly buried hot water networks — Part 2: Installation;
— EN 14419, District heating pipes — Bonded single and twin pipe systems for directly buried hot water
networks — Surveillance systems;
— EN 15632 (all parts), District heating pipes — Pre-insulated flexible pipe systems;
— EN 15698-1, District heating pipes — Bonded twin pipe systems for directly buried hot water networks —
Part 1: Factory made twin pipe assembly of steel service pipes, polyurethane thermal insulation and one
casing of polyethylene ;
— EN 15698-2, District heating pipes — Bonded twin pipe systems for directly buried hot water networks —
Part 2: Factory made fitting and valve assemblies of steel service pipes, polyurethane thermal insulation
and one casing of polyethylene
— EN 17248, District heating and district cooling pipe systems — Terms and definitions.
1 Scope
This document specifies requirements and test methods for factory made thermally insulated bonded fitting
assemblies for hot water networks in accordance with EN 13941-1, comprising a steel service fitting, rigid
polyurethane foam thermal insulation and a casing of polyethylene.
The fitting assembly could also include the following additional elements: measuring wires, spacers and
diffusion barriers.
This document covers the following fitting assemblies: bend, tee, reducer, single use compensator and
anchor.
This document applies to fitting assemblies with a minimum design pressure of 1,6 MPa (overpressure).
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes
requirements of this document. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
EN 253, District heating pipes — Bonded single pipe systems for directly buried hot water networks — Factory
made pipe assembly of steel service pipe, polyurethane thermal insulation and a casing of polyethylene
EN 10204, Metallic products — Types of inspection documents
EN 10216-2, Seamless steel tubes for pressure purposes - Technical delivery conditions — Part 2: Non-alloy and
alloy steel tubes with specified elevated temperature properties
EN 10217-2, Welded steel tubes for pressure purposes — Technical delivery conditions — Part 2: Electric
welded non-alloy and alloy steel tubes with specified elevated temperature properties
EN 10217-5, Welded steel tubes for pressure purposes — Technical delivery conditions — Part 5: Submerged
arc welded non-alloy and alloy steel tubes with specified elevated temperature properties
EN 10253-2, Butt-welding pipe fittings — Part 2: Non alloy and ferritic alloy steels with specific inspection
requirements
EN 12814-1, Testing of welded joints of thermoplastics semi-finished products — Part 1: Bend test
EN 13018, Non-destructive testing — Visual testing — General principles
EN 13941-1, District heating pipes — Design and installation of thermal insulated bonded single and twin pipe
systems for directly buried hot water networks — Part 1: Design
EN 13941-2, District heating pipes — Design and installation of thermal insulated bonded single and twin pipe
systems for directly buried hot water networks — Part 2: Installation
EN 14419, District heating pipes — Preinsulated bonded pipe systems for directly buried hot water networks —
Surveillance systems
EN 14870-1, Petroleum and natural gas industries — Induction bends, fittings and flanges for pipeline
transportation systems — Part 1: Induction bends (ISO 15590-1)
EN 17248, District heating and district cooling pipe systems — Terms and definitions
EN ISO 3452-1, Non-destructive testing — Penetrant testing — Part 1: General principles (ISO 3452-1)
EN ISO 5579, Non-destructive testing — Radiographic testing of metallic materials using film and X- or gamma
rays — Basic rules (ISO 5579)
EN ISO 5817, Welding — Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding
excluded) — Quality levels for imperfections (ISO 5817)
EN ISO 8501-1, Preparation of steel substrates before application of paints and related products — Visual
assessment of surface cleanliness — Part 1: Rust grades and preparation grades of uncoated steel substrates
and of steel substrates after overall removal of previous coatings (ISO 8501-1)
EN ISO 9606-1, Qualification testing of welders — Fusion welding — Part 1: Steels (ISO 9606-1)
EN ISO 9692-1:2013, Welding and allied processes — Types of joint preparation — Part 1: Manual metal arc
welding, gas-shielded metal arc welding, gas welding, TIG welding and beam welding of steels
(ISO 9692-1:2013)
EN ISO 9934-1, Non-destructive testing — Magnetic particle testing — Part 1: General principles (ISO 9934-1)
EN ISO 10675-1, Non-destructive testing of welds — Acceptance levels for radiographic testing — Part 1: Steel,
nickel, titanium and their alloys (ISO 10675-1)
EN ISO 11666, Non-destructive testing of welds — Ultrasonic testing — Acceptance levels (ISO 11666)
EN ISO 14732, Welding personnel — Qualification testing of welding operators and weld setters for
mechanized and automatic welding of metallic materials (ISO 14732)
EN ISO 15607, Specification and qualification of welding procedures for metallic materials — General rules
(ISO 15607)
EN ISO 16810, Non-destructive testing — Ultrasonic testing — General principles (ISO 16810)
EN ISO 17636-1, Non-destructive testing of welds — Radiographic testing — Part 1: X- and gamma-ray
techniques with film (ISO 17636-1)
EN ISO 17636-2, Non-destructive testing of welds — Radiographic testing — Part 2: X- and gamma-ray
techniques with digital detectors (ISO 17636-2)
EN ISO 17637, Non-destructive testing of welds — Visual testing of fusion-welded joints (ISO 17637)
EN ISO 17638, Non-destructive testing of welds — Magnetic particle testing (ISO 17638)
EN ISO 17640, Non-destructive testing of welds — Ultrasonic testing — Techniques, testing levels, and
assessment (ISO 17640)
EN ISO 23277, Non-destructive testing of welds — Penetrant testing — Acceptance levels (ISO 23277)
EN ISO 23278, Non-destructive testing of w
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.