iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 1323:2007

(Main)

Adhesives for tiles - Concrete slabs for tests

Adhesives for tiles - Concrete slabs for tests

This European Standard specifies the substrate (concrete slab) to be used for the determination of the properties of adhesives for tiles.
This European Standard does not contain performance requirements or recommendations for the design and installation of ceramic tiles.
NOTE   Ceramic tile adhesives can also be used for other types of tiles (natural and agglomerated stones etc), if they do not adversely affect the stones.

Mörtel und Klebstoffe für Fliesen und Platten - Betonplatten für Prüfungen

Diese Europäische Norm legt den Untergrund (Betonplatte) fest, der zur Bestimmung der Eigenschaften von Mörteln und Klebstoffen für Fliesen und Platten zu verwenden ist.
In dieser Europäischen Norm sind keine Leistungsanforderungen oder Empfehlungen für die Ausführung und Verarbeitung von keramischen Fliesen und Platten enthalten.
ANMERKUNG   Mörtel und Klebstoffe für keramische Fliesen und Platten können auch für andere Arten von Fliesen und Platten (Naturwerkstein, Betonwerkstein usw.) verwendet werden, wenn diese Materialien hierdurch nicht beeinträchtigt werden

Colles à carrelage - Plaques de béton pour essais

La présente Norme européenne spécifie le support (plaque de béton) devant être utilisé pour déterminer les propriétés des colles à carrelage.
La présente Norme européenne ne contient pas d’exigences de performance, ni de recommandations pour la conception et la pose des carreaux céramiques.
NOTE   Les colles pour carreaux céramiques peuvent également être utilisées pour d’autres types de carrelages (carreaux de pierres naturelles ou de pierres reconstituées etc.) lorsqu’elles sont compatibles.

Lepila za ploščice - Betonska plošča za preskus

General Information

Status
Withdrawn
Publication Date
28-Aug-2007
Withdrawal Date
14-Feb-2017
ICS
83.180 - Adhesives
91.100.10 - Cement. Gypsum. Lime. Mortar
91.100.30 - Concrete and concrete products
Technical Committee
CEN/TC 67 - Ceramic tiles
Drafting Committee
CEN/TC 67/WG 3 - Adhesives and grouts for tiles
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
15-Feb-2017
Ref Project
SIST EN 1323:2007 - Adhesives for tiles - Concrete slabs for tests

Relations

Replaces
EN 1323:1996 - Adhesives for tiles - Concrete slab for test
Effective Date
22-Dec-2008
Replaces
EN 1323:1996/A1:1998 - Adhesives for tiles - Concrete slab for test
Effective Date
22-Dec-2008
Replaced By
EN 12004-2:2017 - Adhesives for ceramic tiles - Part 2: Test methods
Effective Date
22-Feb-2017

Buy Standard

EN 1323:2007EN 1323:2007
PreviousNext
Standard
EN 1323:2007
English language
8 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Adhesives for tiles - Concrete slabs for testsColles a carrelage - Plaques de béton pour essaisMörtel und Klebstoffe für Fliesen und Platten - Betonplatten für PrüfungenTa slovenski standard je istoveten z:EN 1323:2007SIST EN 1323:2007en,fr,de91.100.3091.100.1083.180ICS:SIST EN 1323:1998/A1:2000SIST EN 1323:19981DGRPHãþDSLOVENSKI
STANDARDSIST EN 1323:200701-december-2007

EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 1323August 2007ICS 83.180; 91.100.10; 91.100.30Supersedes EN 1323:1996
English VersionAdhesives for tiles - Concrete slabs for testsColles à carrelage - Plaques de béton pour essaisMörtel und Klebstoffe für Fliesen und Platten - Betonplattenfür PrüfungenThis European Standard was approved by CEN on 21 January 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2007 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 1323:2007: E
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 12004-2:2017(Main)
Adhesives for ceramic tiles - Part 2: Test methods
SIST EN 12004-2:2017

This European Standard specifies the methods for determining characteristics for adhesives used in internal and external installation of ceramic tiles.
This European Standard does not contain performance requirements or recommendations for the design and installation of ceramic tiles.
The following test methods are described:
-   determination of open time (8.1);
-   determination of slip (8.2);
-   determination of tensile adhesion strength for cementitious adhesives (8.3);
-   determination of shear adhesion strength of dispersion adhesives (8.4);
-   determination of shear adhesion strength of reaction resin adhesives (8.5);
-   determination of transverse deformation of cementitious adhesives (8.6).
NOTE   Ceramic tile adhesives can be used also for other kinds of tiles (natural and agglomerated stones, etc.), if they do not adversely affect the stones.
WARNING - This European Standard can involve hazardous materials and operations. Persons using this standard should be familiar with normal laboratory practice. This European Standard does not purport to address all the safety problems, if any, associated with its use. It is the responsibility of the user to establish appropriate safety and health practices and to ensure compliance with any European and national regulatory conditions.

  • Standard
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12004-2:2017(Main)
Adhesives for ceramic tiles - Part 2: Test methods
SIST EN 12004-2:2017

This European Standard specifies the methods for determining characteristics for adhesives used in internal and external installation of ceramic tiles.
This European Standard does not contain performance requirements or recommendations for the design and installation of ceramic tiles.
The following test methods are described:
-   determination of open time (8.1);
-   determination of slip (8.2);
-   determination of tensile adhesion strength for cementitious adhesives (8.3);
-   determination of shear adhesion strength of dispersion adhesives (8.4);
-   determination of shear adhesion strength of reaction resin adhesives (8.5);
-   determination of transverse deformation of cementitious adhesives (8.6).
NOTE   Ceramic tile adhesives can be used also for other kinds of tiles (natural and agglomerated stones, etc.), if they do not adversely affect the stones.
WARNING - This European Standard can involve hazardous materials and operations. Persons using this standard should be familiar with normal laboratory practice. This European Standard does not purport to address all the safety problems, if any, associated with its use. It is the responsibility of the user to establish appropriate safety and health practices and to ensure compliance with any European and national regulatory conditions.

  • Standard
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17928-1:2024(Main)
Gas infrastructure - Injection stations - Part 1: General requirements
kSIST FprEN 17928-1:2024

This document establishes the functional requirements for stations for the injection of biomethane, substitute natural gas (SNG) and hydrogen into gas transmission and distribution systems operated with gases (natural gas, biomethane, SNG, hydrogen, gas mixtures) in accordance with European technical rules that ensure the interoperability of systems.
Figure 1 describes the general approach including all the relevant functions that can be installed in different configurations. The injection of Hydrogen is covered separately in EN 17928-3:2024.
This document also applies to refeeding stations that feed such gases back into upstream gas supply networks; see Figure 2.
This document represents the state of the art at the time of its preparation.
This document does not apply to injection stations operating prior to the publication of this document.
This document specifies common basic principles for gas infrastructure. Users of this document are expected to be aware that more detailed national standards and/or codes of practice can exist in the CEN member countries. This document is intended to be applied in association with these national standards and/or codes of practice setting out the above-mentioned basic principles.
In the event of terms of additional requirements in national legislation/regulation than in this document, CEN/TR 13737 (all parts) illustrates these terms.
CEN/TR 13737 (all parts) gives:
—   legislation/regulations applicable in a member state;
—   if appropriate, more restrictive national requirements;
—   a national contact point for the latest information.

  • Draft
    57 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13237:2024(Main)
Potentially explosive atmospheres - Terms and definitions for equipment and protective systems intended for use in potentially explosive atmospheres
oSIST prEN 13237:2022

This document specifies terms and definitions (vocabulary) to be used in suitable standards dealing with equipment and protective systems intended for use in potentially explosive atmospheres within the scope of Directive 2014/34/EU.
NOTE   Terms and definitions avoid misunderstandings that are important in relation to the essential health and safety requirements of Directive 2014/34/EU.

  • Draft
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 19085-7:2024(Main)
Woodworking machines - Safety - Part 7: Surface planing, thickness planing and combined surface/thickness planing machines (ISO 19085-7:2024)
kSIST FprEN ISO 19085-7:2024

This document specifies the safety requirements and measures for
—     surface planing machines, also called jointers,
—     thickness planing machines, also called planers or single surface planers, and
—     combined surface/thickness planing machines
with fixed cutter block position, with an integrated feed in thickness planing mode, with or without demountable power feed device in planing mode, with manual loading and/or unloading of the workpiece, and capable of continuous production use, altogether referred to as “machines”.
The machines are designed to cut solid wood and material with similar physical characteristics to wood (see ISO 19085-1:2021, 3.2).
This document deals with all significant hazards, hazardous situations and events as listed in Annex A relevant to the machines when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer. Reasonably foreseeable misuse has been considered too. Transport, assembly, dismantling, disabling and scrapping phases have also been taken into account.
This document is also applicable to surface planing machines and combined surface/thickness planing machines fitted with an optional mortising device, whose hazards have been dealt with.
This document does not apply to:
a)       machines with more than one cutter block;
b)       machines with a mortising unit driven by a separate motor;
c)        machines where the cutter block is adjustable for depth of cut setting in thickness planing mode;
d)       machines where the conversion from planing to thickness planing mode or vice versa is achieved by mounting or demounting parts/units;
e)       machines where surface planing and thickness planing can be performed at the same time;
f)         machines intended for use in potentially explosive atmosphere;
g)       machines manufactured prior to the publication of this document.

  • Draft
    56 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 2350:2024(Main)
Aerospace series - Circuit breakers - Technical specification
kSIST FprEN 2350:2024
  • Draft
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TS 927-15:2024(Main)
Paints and varnishes - Coating materials and coating systems for exterior wood - Part 15: Assessment of bleeding of coloured wood extractives through a coating by means of a water immersion test
kSIST-TS FprCEN/TS 927-15:2024

This document specifies a test method using water immersion test for assessing the bleeding of coloured wood extractives through a coating. Leachates of coated and uncoated wood are collected after the immersion procedure and their colour is compared. The colour of the coated wood before and after immersion tests is also compared. This document does not specify acceptance values for colour differences that can be tolerated and it is not applicable to staining caused by knots for which there is a different test method (see EN 927 7).
NOTE   The method has been developed for oak and chestnut wood and might be applicable for other wood substrates containing water soluble extractives.

  • Draft
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 19085-5:2024(Main)
Woodworking machines - Safety - Part 5: Dimension saws (ISO 19085-5:2024)
kSIST FprEN ISO 19085-5:2024

This document specifies the safety requirements and measures for dimension saws (defined in 3.1), capable of continuous production use and hereinafter referred to also as “machines”.
The machines are designed to cut solid wood and material with similar physical characteristics to wood.
This document deals with all significant hazards, hazardous situations and events, listed in Annex A, relevant to the machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer; reasonably foreseeable misuse has been considered too. Transport, assembly, dismantling, disabling and scrapping phases have also been taken into account.
This document is also applicable to machines fitted with one or more of the following devices/additional working units, whose hazards have been dealt with:
a)       device to raise and lower the main saw blade and scoring saw blade;
b)       device to tilt the main saw blade and scoring saw blade for angled cutting in one or both directions;
c)        device for scoring;
d)       device for grooving with milling tool with a width not exceeding 20 mm;
e)       demountable power feed unit;
f)         power-operated sliding table;
g)       workpiece clamping.
This document is not applicable to machines intended for use in potentially explosive atmospheres or to machines manufactured prior to the date of its publication.

  • Draft
    66 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16186-6:2024(Main)
Railway applications - Driver's cab - Part 6: Integration of displays, controls and indicators for tram vehicles
kSIST FprEN 16186-6:2024

This document is applicable to vehicles operating on tram networks.
This document gives design requirements and guidance in order to ensure visibility and operability of displays, controls and indicators in the cab in all operating conditions (day, night, natural or artificial lighting).
It covers four aspects:
-   the characteristics of the displays, controls and indicators in order to ensure proper visibility: i.e. range of luminance and contrast as well as the possibility of adjustment of perceived brightness;
-   the requirements for the location of the displays, keyboards, controls and indicators in the cab and on the driver’s desk: i.e. position, angle of visibility, etc. with consideration of the normal driving position and the working environment (windscreen, natural or artificial lighting in the cab, unwanted glare and reflections, etc.);
-   the characteristics and requirements for the location of microphones and loudspeakers;
-   design of symbols.
NOTE   All element numbers within the text refer to Table B.1.
This document does not apply to refurbishment of existing vehicles. This document is not intended to be applicable to driver's auxiliary desk, except for 5.3.13, Clause 6, 7.1.2, Clause 9 and Table B.1.

  • Draft
    40 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17450-2:2024(Main)
Fixed firefighting systems - Water mist systems - Part 2: Product characteristics and test methods for nozzles
kSIST FprEN 17450-2:2024

This document specifies product characteristics and test methods of open nozzles and automatic nozzles for use in water mist systems.
NOTE   All pressure data in this document are given as gauge pressures in bar.

  • Draft
    38 pages
    English language
    sale 10% off
    e-Library read for
    1 day