EN ISO 10416:2009
(Main)Petroleum and natural gas industries - Drilling fluids - Laboratory testing (ISO 10416:2008)
Petroleum and natural gas industries - Drilling fluids - Laboratory testing (ISO 10416:2008)
ISO 10416:2008 provides procedures for the laboratory testing of both drilling-fluid materials and drilling-fluid physical, chemical and performance properties. It is applicable to both water-based and oil-based drilling fluids, as well as the base or “make-up” fluid.
ISO 10416:2008 is not applicable as a detailed manual on drilling fluid control procedures. Recommendations regarding agitation and testing temperature are presented because the agitation history and temperature have a profound effect on drilling fluid properties.
Erdöl- und Erdgasindustrie - Bohrspülungen - Laborversuche (ISO 10416:2008)
Industries du pétrole et du gaz naturel - Fluides de forage - Essais en laboratoire (ISO 10416:2008)
L'ISO 10416:2008 fournit des modes opératoires pour les essais de laboratoire à la fois en ce qui concerne les matériaux de fluides de forage et les propriétés physiques, chimiques et les performances des fluides de forage. Elle est applicable aux fluides de forage à base d'eau et aux fluides de forage à base d'huile, de même qu'au fluide de base ou au fluide de «constitution».
Elle n'est pas applicable en tant que manuel détaillé relatif aux modes opératoires de contrôle des fluides de forage. Des recommandations en ce qui concerne l'agitation et la température d'essais sont présentées du fait que l'historique de l'agitation et la température ont un effet profond sur les propriétés des fluides de forage.
Industrija za predelavo nafte in zemeljskega plina - Vrtalne tekočine - Laboratorijsko preskušanje (ISO 10416:2008)
Ta mednarodni standard predpisuje postopke za laboratorijsko preskušanje vrtalnih tekočin, tako materialov kot tudi njihovih fizikalnih, kemičnih in proizvodnih lastnosti. Velja za vrtalne tekočine na vodni osnovi in na osnovi olja ter za osnovne ali nadomestne tekočine. Ne uporablja se kot natančen priročnik za kontrolni postopek za vrtalne tekočine. Priporočila glede tresenja in temperature preskušanja so navedena, ker imata potek tresenja in temperatura velik vpliv na lastnosti vrtalnih tekočin.
General Information
Related Packages
Standards Content (Sample)
SLOVENSKI STANDARD
01-februar-2010
,QGXVWULMD]DSUHGHODYRQDIWHLQ]HPHOMVNHJDSOLQD9UWDOQHWHNRþLQH
/DERUDWRULMVNRSUHVNXãDQMH ,62
Petroleum and natural gas industries - Drilling fluids - Laboratory testing (ISO
10416:2008)
Erdöl- und Erdgasindustrie - Bohrspülungen - Laborversuche (ISO 10416:2008)
Industries du pétrole et du gaz naturel - Fluides de forage - Essais en laboratoire (ISO
10416:2008)
Ta slovenski standard je istoveten z: EN ISO 10416:2009
ICS:
75.100 Maziva Lubricants, industrial oils and
related products
75.180.10 Oprema za raziskovanje in Exploratory and extraction
odkopavanje equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 10416
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2009
ICS 75.100; 75.180.10
English Version
Petroleum and natural gas industries - Drilling fluids - Laboratory
testing (ISO 10416:2008)
Industries du pétrole et du gaz naturel - Fluides de forage - Erdöl- und Erdgasindustrie - Bohrspülungen -
Essais en laboratoire (ISO 10416:2008) Laborversuche (ISO 10416:2008)
This European Standard was approved by CEN on 15 November 2009.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10416:2009: E
worldwide for CEN national Members.
Contents Page
Foreword .3
Foreword
The text of ISO 10416:2008 has been prepared by Technical Committee ISO/TC 67 “Materials, equipment
and offshore structures for petroleum, petrochemical and natural gas industries” of the International
Organization for Standardization (ISO) and has been taken over as EN ISO 10416:2009 by Technical
Committee CEN/TC 12 “Materials, equipment and offshore structures for petroleum, petrochemical and
natural gas industries” the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by June 2010, and conflicting national standards shall be withdrawn at
the latest by June 2010.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 10416:2008 has been approved by CEN as a EN ISO 10416:2009 without any modification.
INTERNATIONAL ISO
STANDARD 10416
Second edition
2008-06-01
Petroleum and natural gas industries —
Drilling fluids — Laboratory testing
Industries du pétrole et du gaz naturel — Fluides de forage — Essais
en laboratoire
Reference number
ISO 10416:2008(E)
©
ISO 2008
ISO 10416:2008(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2008
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2008 – All rights reserved
ISO 10416:2008(E)
Contents Page
Foreword. vii
Introduction . viii
1 Scope .1
2 Normative references .1
3 Terms and definitions .2
4 Symbols and abbreviations .3
5 Barite.6
5.1 Principle.6
5.2 Reagents and apparatus .6
5.3 Sampling.7
5.4 Calculation of moisture content.7
5.5 Sieve analysis .7
5.6 Sedimentation analysis.8
6 Barite performance.12
6.1 Principle.12
6.2 Reagents and apparatus .12
6.3 Base drilling fluid preparation.13
6.4 Rheology test .13
6.5 Calculation.14
7 Abrasiveness of weighting materials .14
7.1 Principle.14
7.2 Reagents and apparatus .15
7.3 Determination of abrasion .15
8 Mercury in drilling fluid barite .17
8.1 Principle.17
8.2 Reagents and apparatus .17
8.3 Preparation of standards .19
8.4 Sample digestion .19
8.5 Check for recovery of Hg during digestion.20
8.6 Analysis of standards and samples.20
8.7 Calculation.20
9 Cadmium and lead in drilling fluid barite .21
9.1 Principle.21
9.2 Reagents and apparatus .21
9.3 Preparation of combined cadmium and lead standards .22
9.4 Sample digestion .22
9.5 Analysis of standards and samples.22
9.6 Calculation.23
10 Arsenic in drilling fluid barite .23
10.1 Principle.23
10.2 Reagents and apparatus .24
10.3 Preparation of standards .25
10.4 Sample digestion .25
10.5 Analysis of standards and samples.26
10.6 Calculation.26
11 Bridging materials for regaining circulation.26
ISO 10416:2008(E)
11.1 Principle . 26
11.2 Apparatus. 27
11.3 Preparation of test drilling fluid. 27
11.4 Static slot test. 27
11.5 Dynamic slot test . 28
11.6 Static marble bed test. 28
11.7 Dynamic marble bed test.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.