CEN ISO/TR 13881:2011
(Main)Petroleum and natural gas industries - Classification and conformity assessment of products, processes and services (ISO/TR 13881:2000)
Petroleum and natural gas industries - Classification and conformity assessment of products, processes and services (ISO/TR 13881:2000)
This Technical Report describes:
_ two classification methods (one based on calculated risk, the other on judgement of risk) which may be used to
determine the appropriate conformity assessment system for products, processes and services;
_ a set of five conformity assessment systems from which the most suitable is chosen when conformity
assessment of products, processes and services is required.
NOTE Alternative classification models may be used provided their results are consistent with the conformity assessment
systems to be applied.
Erdöl- und Erdgasindustrie - Klassifizierung und Konformitätsbewertung von Produkten, Verfahren und Dienstleistungen (ISO/TR 13881:2000)
Industries du pétrole et du gaz naturel - Classification et évaluation de la conformité des produits, procédés et services (ISO/TR 13881:2000)
Industrija za predelavo nafte in zemeljskega plina - Klasifikacija ter ugotavljanje skladnosti proizvodov, procesov in storitev (ISO/TR 13881:2000)
To tehnično poročilo opisuje: - dve metodi klasifikacije (eno na osnovi izračunanega tveganja, drugo na presoji tveganja), ki se lahko uporabljata za določevanje ustreznega sistema za ugotavljanje skladnosti proizvodov, procesov in storitev; - nabor petih sistemov za ugotavljanje skladnosti, od katerih se izbere najprimernejši, kadar je potrebno ugotavljanje skladnosti proizvodov, procesov in storitev.
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-januar-2012
Industrija za predelavo nafte in zemeljskega plina - Klasifikacija ter ugotavljanje
skladnosti proizvodov, procesov in storitev (ISO/TR 13881:2000)
Petroleum and natural gas industries - Classification and conformity assessment of
products, processes and services (ISO/TR 13881:2000)
Erdöl- und Erdgasindustrie - Formeln und Berechnungen zur Festlegung der
Eigenschaften von Futterrohren, Steigrohren, Bohrrohren und Leitungsrohren (ISO/TR
13881:2000)
Industries du pétrole et du gaz naturel - Classification et évaluation de la conformité des
produits, procédés et services (ISO/TR 13881:2000))
Ta slovenski standard je istoveten z: CEN ISO/TR 13881:2011
ICS:
03.120.20 Certificiranje proizvodov in Product and company
podjetij. Ugotavljanje certification. Conformity
skladnosti assessment
75.020 Pridobivanje in predelava Extraction and processing of
nafte in zemeljskega plina petroleum and natural gas
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
TECHNICAL REPORT
CEN ISO/TR 13881
RAPPORT TECHNIQUE
TECHNISCHER BERICHT
February 2011
ICS 75.080; 75.020
English Version
Petroleum and natural gas industries - Classification and
conformity assessment of products, processes and services
(ISO/TR 13881:2000)
Industries du pétrole et du gaz naturel - Classification et Erdöl- und Erdgasindustrie - Klassifizierung und
évaluation de la conformité des produits, procédés et Konformitätsbewertung von Produkten, Verfahren und
services (ISO/TR 13881:2000) Dienstleistungen (ISO/TR 13881:2000)
This Technical Report was approved by CEN on 27 December 2010. It has been drawn up by the Technical Committee CEN/TC 12.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN ISO/TR 13881:2011: E
worldwide for CEN national Members.
Contents Page
Foreword .3
Foreword
The text of ISO/TR 13881:2000 has been prepared by Technical Committee ISO/TC 67 “Materials, equipment
and offshore structures for petroleum, petrochemical and natural gas industries” of the International
Organization for Standardization (ISO) and has been taken over as CEN ISO/TR 13881:2011 by Technical
Committee CEN/TC 12 “Materials, equipment and offshore structures for petroleum, petrochemical and
natural gas industries” the secretariat of which is held by AFNOR.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
Endorsement notice
The text of ISO/TR 13881:2000 has been approved by CEN as a CEN ISO/TR 13881:2011 without any
modification.
TECHNICAL ISO/TR
REPORT 13881
First edition
2000-04-15
Petroleum and natural gas industries —
Classification and conformity assessment
of products, processes and services
Industries du pétrole et du gaz naturel — Classification et évaluation
de la conformité des produits, procédés et services
Reference number
ISO/TR 13881:2000(E)
©
ISO 2000
ISO/TR 13881:2000(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 � CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 734 10 79
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
ii © ISO 2000 – All rights reserved
ISO/TR 13881:2000(E)
Contents Page
Foreword.iv
Introduction.v
1 Scope .1
2 References.1
3 Terms and definitions .1
4 Classification principles .2
5 Classification method based on calculation.3
6 Classification method based on judgement .4
7 Limitations.6
8 Conformity assessment systems.6
9 System A.8
10 System B.10
11 System C.12
12 System D.13
13 System E.14
Annex A Classification method based on judgement.15
Annex B Frequently asked questions.18
ISO/TR 13881:2000(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
The main task of technical committees is to prepare International Standards. Draft International Standards adopted
by the technical committees are circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting a vote.
In exceptional circumstances, when a technical committee has collected data of a different kind from that which is
normally published as an International Standard ("state of the art", for example), it may decide by a simple majority
vote of its participating members to publish a Technical Report. A Technical Report is entirely informative in nature
and does not have to be reviewed until the data it provides are considered to be no longer valid or useful.
Attention is drawn to the possibility that some of the elements of this Technical Report may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO/TR 13881 was prepared by Technical Committee ISO/TC 67, Materials, equipment and offshore structures for
petroleum and natural gas industries.
iv © ISO 2000 – All rights reserved
ISO/TR 13881:2000(E)
Introduction
When a user/purchaser wishes to procure a product, process or service, the user/purchaser may produce a
functional specification (see ISO 13879). If so, the manufacturer/supplier provides a technical specification (see
ISO 13880) as the basis for manufacturing or execution. The user/purchaser decides on the extent to which it is
necessary to determine, directly or indirectly, that relevant requirements are fulfilled and states this in the contract
with the manufacturer/supplier.
This document describes:
� two methodologies which enable the required degree of assurance to be determined by classification, which in
turn dictates the conformity assessment system;
� a set of five conformity assessment systems which when applied can give an increasing level of confidence
that the product, process or service conforms to stated requirements.
TECHNICAL REPORT ISO/TR 13881:2000(E)
Petroleum and natural gas industries — Classification and
conformity assessment of products, processes and services
1 Scope
This Technical Report describes:
� two classification methods (one based on calculated risk, the other on judgement of risk) which may be used to
determine the appropriate conformity assessment system for products, processes and services;
� a set of five conformity assessment systems from which the most suitable is chosen when conformity
assessment of products, processes and services is required.
NOTE Alternative classification models may be used provided their results are consistent with the conformity assessment
systems to be applied.
2 References
ISO/IEC Guide 2:1996, Standardization and related activities — General vocabulary.
ISO/IEC Guide 22:1996, General criteria for supplier's declaration of conformity.
ISO/IEC Guide 28:1982, General rules for a model third-party certification system for products.
1)
ISO 9001:— , Quality management systems — Requirements.
ISO 9002:1994, Quality systems — Model for quality assurance in production, installation and servicing.
ISO 9003:1994, Quality systems — Model for quality assurance in final inspection and test.
ISO 13879:1999, Petroleum and natural gas industries — Content and drafting of a functional specification.
ISO 13880:1999, Petroleum and natural gas industries — Content and drafting of a technical specification.
3 Terms and definitions
For the purposes of this Technical Report, the terms and definitions of conformity-assessment-related terms given
in ISO/IEC Guide 2 apply, with the exception of the terms defined below.
3.1
class
number assigned to a product, process or service, associated with the risk of its failure during use due to design or
manufacturing, process or service errors, that indicates the appropriate conformity assessment system to be
adopted
1) To be published. (Revision of ISO 9001:1994)
ISO/TR 13881:2000(E)
NOTE The classification of a product, process or service does not take into consideration failure due to misuse or incorrect
maintenance of the product, process or service.
3.2
probability of failure
frequency of occurrence of a product, process or service failure happening within one year divided by the total
number of the particular products, processes or services in operation during the same year
3.3
consequence of failure
results of the failure of the product, process or service
NOTE In the petroleum and natural gas industries, the most commonly used measure of consequence is financial cost. This
implies that the intangible aspects of the results following a failure, such as community acceptance, be translated to financial
cost. The cost for failure can comprise cost for restoring the environment (i.e. damage to the enviro
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.