iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 280:2013/FprA1

(Amendment)

Mobile elevating work platforms - Design calculations - Stability criteria - Construction - Safety - Examinations and tests

Mobile elevating work platforms - Design calculations - Stability criteria - Construction - Safety - Examinations and tests

This European Standard specifies safety requirements and measures for all types and sizes of Mobile Elevating Work Platform intended to move persons to working positions where they are carrying out work from the work platform (WP) with the intention that persons are getting on and off the work platform only at access positions at ground level or on the chassis.
NOTE Machines designed for the handling of goods which are equipped with work platforms as interchangeable equipment are regarded as MEWPs.
This European Standard is applicable to the structural design calculations and stability criteria, construction, safety examinations and tests before MEWPs are first put into service. It identifies the hazards arising from the use of MEWPs and describes methods for the elimination or reduction of these hazards.
Classification: MEWPs are divided into two main groups:
a) Group A: MEWPs where the vertical projection of the centre of the area of the platform in all platform configurations at the maximum chassis inclination specified by the manufacturer is always inside the tipping lines.
b) Group B: All other MEWPs.
Relating to travelling, MEWPs are divided into three types:
1) Type 1: Travelling is only allowed with the MEWP in its transport configuration;
2) Type 2: Travelling with raised work platform is controlled from a point of control at the chassis;
3) Type 3: Travelling with raised work platform is controlled from a point of control at the work platform.
NOTE Type 2 and type 3 can be combined.

Fahrbare Hubarbeitsbühnen - Berechnung - Standsicherheit - Bau - Sicherheit - Prüfungen

Plates-formes élévatrices mobiles de personnel - Calculs de conception - Critères de stabilité - Construction - Sécurité - Examens et essais

Premične dvižne delovne ploščadi - Konstrukcijski izračuni - Kriteriji stabilnosti - Konstrukcije - Varnost - Pregledi in preskusi

General Information

Status
Not Published
ICS
53.020.99 - Other lifting equipment
Technical Committee
CEN/TC 98 - Lifting platforms
Drafting Committee
CEN/TC 98/WG 1 - Mobile elevating work platforms
Current Stage
5060 - Closure of Vote - Formal Approval
Start Date
26-May-2015
Due Date
13-Sep-2016
Completion Date
26-May-2015
Directive
2006/42/EC - Directive 2006/42/EC of the European Parliament and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast)
Mandate
M/396 - Mandate to CEN and Cenelec for standardisation in the field of machinery
M/BC/CEN/91/1 - Standardization request to CEN/CENELEC concerning machines presenting hazards due to mobility or load lifting
Ref Project
SIST EN 280:2013/kprA1:2015 - Mobile elevating work platforms - Design calculations - Stability criteria - Construction - Safety - Examinations and tests

Relations

Merged Into
EN 280:2013+A1:2015 - Mobile elevating work platforms - Design calculations - Stability criteria - Construction - Safety - Examinations and tests
Effective Date
18-Jan-2023
Amends
EN 280:2013 - Mobile elevating work platforms - Design calculations - Stability criteria - Construction - Safety - Examinations and tests
Effective Date
11-Sep-2013

Buy Standard

EN 280:2013/kprA1:2015 - BARVEEN 280:2013/kprA1:2015 - BARVE
PreviousNext
Draft
EN 280:2013/kprA1:2015 - BARVE
English language
17 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 280:2013/kprA1:2015
01-junij-2015
3UHPLþQHGYLåQHGHORYQHSORãþDGL.RQVWUXNFLMVNLL]UDþXQL.ULWHULMLVWDELOQRVWL
.RQVWUXNFLMH9DUQRVW3UHJOHGLLQSUHVNXVL
Mobile elevating work platforms - Design calculations - Stability criteria - Construction -
Safety - Examinations and tests
Fahrbare Hubarbeitsbühnen - Berechnung - Standsicherheit - Bau - Sicherheit -
Prüfungen
Plates-formes élévatrices mobiles de personnel - Calculs de conception - Critères de
stabilité - Construction - Sécurité - Examens et essais
Ta slovenski standard je istoveten z: EN 280:2013/FprA1
ICS:
53.020.99 Druga dvigalna oprema Other lifting equipment
SIST EN 280:2013/kprA1:2015 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 280:2013/kprA1:2015

---------------------- Page: 2 ----------------------

SIST EN 280:2013/kprA1:2015

EUROPEAN STANDARD
FINAL DRAFT
EN 280:2013
NORME EUROPÉENNE

EUROPÄISCHE NORM
FprA1
March 2015
ICS 53.020.99
English Version
Mobile elevating work platforms - Design calculations - Stability
criteria - Construction - Safety - Examinations and tests
Plates-formes élévatrices mobiles de personnel - Calculs de Fahrbare Hubarbeitsbühnen - Berechnung - Standsicherheit
conception - Critères de stabilité - Construction - Sécurité - - Bau - Sicherheit - Prüfungen
Examens et essais
This draft amendment is submitted to CEN members for formal vote. It has been drawn up by the Technical Committee CEN/TC 98.

This draft amendment A1, if approved, will modify the European Standard EN 280:2013. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.

This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has
the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 280:2013/FprA1:2015 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 280:2013/kprA1:2015
EN 280:2013/FprA1:2015 (E)
Contents
Page
1 Modification to Clause 2 "Normative references" .4
2 Modification to 5.1.2 .4
3 Modification to 5.2.2 "Loads and forces" .4
4 Modification to 5.2.3.2 "Structural loads" .4
5 Modification to 5.2.3.5 “Special loads and forces” .4
6 Modification to 5.2.4 "Stability calculations" .4
7 Modification to 5.2.5.2 “Calculation methods” .5
8 Modification to 5.2.5.2 “Calculation methods”, Table 2 .5
9 Modification to 5.2.5.2 "Calculation methods" .5
10 Modification to 5.2.5.3 “Analysis” .5
11 Modification to 5.6.14 .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 1493:2022(Main)
Vehicle lifts
SIST EN 1493:2023

This document is applicable to stationary and mobile vehicle lifts, which are not intended to lift persons but which are designed to raise vehicles totally, for the purpose of examining and working on or under the vehicles whilst in a raised position. The vehicle lift may consist of one or more lifting units.
Power supply to the vehicle lift by internal combustion engines is not considered.
The floor or ground supporting the vehicle lift in use is assumed to be horizontal.
This document does not exclude a person from entering a lifted vehicle on wheel supporting lifts, e.g. for special works or for periodical technical inspection, and vehicle lifts for rail-bound vehicles.
This document does not contain requirements for hazards which may arise on vehicle lifts where the carrying device can be tilted.
NOTE Noise does not play a role in vehicle lifts in the majority of cases and is therefore not considered in this document.
This document does not apply to:
- vehicle lifts movable when loaded;
- equipment for power driven parking of motor vehicles (see EN 14010:2003+A1:2009).
This document is applicable to vehicle lifts which are manufactured six months after the date of its publication as a European Standard.

  • Standard
    112 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 280-1:2022(Main)
Mobile elevating work platforms - Part 1: Design calculations - Stability criteria - Construction - Safety - Examinations and tests
SIST EN 280-1:2022

1.1   This document specifies safety requirements and measures for all types and sizes of Mobile Elevating Work Platform (MEWP, see 3.1) intended to move persons to working positions where they are carrying out work from the work platform (WP) with the intention that persons are getting on and off the work platform only at access positions at ground level or on the chassis.
NOTE   Machines designed for the handling of goods which are equipped with work platforms as interchangeable equipment are regarded as MEWPs.
1.2   This document is applicable to the structural design calculations and stability criteria, construction, safety examinations and tests before MEWPs are first put into service. It identifies the hazards arising from the use of MEWPs and describes methods for the elimination or reduction of these hazards.
It does not cover the hazards arising from:
a)   use in potentially explosive atmospheres;
b)   work from the platform on external live electric systems;
c)   use of compressed gases for load bearing components;
d)   getting on and off the work platform at changing levels;
e)   specific applications (e.g. railway, ships) covered by National or local regulations.
1.3   This document does not apply to:
a)   machinery serving fixed landings (see e.g. EN 81-20:2020 and EN 81-50:2020, EN 12159:2012);
b)   fire-fighting and fire rescue appliances (see e.g. EN 1777:2010);
c)   unguided work cages suspended from lifting appliances (see e.g. EN 1808:2015);
d)   elevating operator position on rail dependent storage and retrieval equipment (see EN 528:2021);
e)   tail lifts (see EN 1756-1:2021 and EN 1756-2:2004+A1:2009);
f)   mast climbing work platforms (see EN 1495:1997+A2:2009);
g)   fairground equipment;
h)   lifting tables (see EN 1570-1:2011+A1:2014 and EN 1570-2:2016);
i)   aircraft ground support equipment (see e.g. EN 1915-1:2013 and EN 1915-2:2001+A1:2009);
j)   elevating operator positions on industrial trucks (see EN ISO 3691-3:2016).
1.4   Classification:
MEWPs are divided into two main groups:
a)   Group A: MEWPs where the vertical projection of the centre of the area of the platform in all platform configurations at the maximum chassis inclination specified by the manufacturer is always inside the tipping lines.
b)   Group B: All other MEWPs.
Relating to travelling, MEWPs are divided into three types:
1)   Type 1: Travelling is only allowed with the MEWP in its transport position;
2)   Type 2: Travelling with lifted work platform is controlled from a point of control at the chassis;
3)   Type 3: Travelling with lifted work platform is controlled from a point of control at the work platform.
NOTE   Type 2 and type 3 can be combined.

  • Standard
    126 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 280-2:2022(Main)
Mobile elevating work platforms - Part 2: Additional safety requirements for load lifting appliances on the extending lifting structure and work platform
SIST EN 280-2:2022

This document, which is to be used in conjunction with EN 280-1:2022, specifies the additional safety requirements for MEWPs of Type 1 Group B equipped with a load lifting appliance. The load-lifting appliance is designed for lifting suspended loads only as part of the task being carried out by personnel from the work platform. This document deals with the additional hazards, hazardous situations and events relevant to load lifting appliances either on the extending lifting structure or on the work platform, when the MEWP and load lifting appliance are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer of the MEWP. The significant hazards covered by this document are listed in Annex A.
This document does not cover the following:
a)   the use of a MEWP for lifting persons as a suspended load;
b)   the use of a MEWP for lifting suspended loads from a control position other than the work platform;
c)   requirements for lifting accessories;
d)   lifting or lowering of suspended loads for general materials handling as carried out by a crane;
e)   MEWPs compliant with EN 280-1:2022, 4.4.1.5 and/or 4.4.1.6 (enhanced stability and overload criteria);
f)   MEWPS others than Type1 Group B.
Load lifting appliance can be:
g)   fixed load attachment points on the work platform or on the extending lifting structure where the load can be positioned in reach of the personnel on the platform;
h)   lifting equipment for lifting or lowering the load with a stationary platform. The equipment is attached to the work platform or extending structure and may have a load lifting jib.
NOTE   The lifting equipment can be either permanently attached or removable.

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1756-1:2021(Main)
Tail lifts - Platform lifts for mounting on wheeled vehicles - Safety requirements - Part 1: Tail lifts for goods
SIST EN 1756-1:2021

This document specifies safety requirements for design of tail lifts as defined in 3.1 for mounting on wheeled goods vehicles. It also specifies the verification of such tail lifts and the safety information that has to be provided for their use.
This document deals with the technical requirements to minimize the hazards listed in Clause 4 which can arise during the operation of tail lifts when carried out in accordance with the specifications as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer or his authorized representative.
It applies to tail lifts:
-   used for the purpose of loading and/or unloading such vehicles;
-   intended to be fitted, temporarily or permanently, either inside or on the front, side or rear of the wheeled vehicle;
-   driven either by hand or power operated;
-   equipped with a platform to support loads which comprise goods, an operator, or a combination of the two;
-   with a maximum lifting height not exceeding 3 m above ground when the platform is unloaded;
-   rotary type with a maximum lifting height not exceeding 2 m;
-   used as a link bridge when intended by the manufacturer.
NOTE   A tail lift is not to be confused with a link bridge attached to a loading dock which is included within the definition of a dock leveller and is outside the scope of this document.
Loading and/or unloading operations include the use of a tail lift to lift and/or lower loads.
This document does not establish the additional requirements for:
-   the risk of falling when operating under 2 m height;
-   overloading at vehicle floor level;
-   drive system with lead screw and nuts;
-   operation in severe conditions (e.g. extreme environmental conditions such as freezer applications, high temperatures, corrosive environment, tropical environment, contaminating environments, strong magnetic fields);
-   operations subject to special rules (e.g. potentially explosive atmospheres);
-   supply by electrical networks and the electrical circuit;
-   power take off part of the system;
-   electromagnetic compatibility (emission-immunity);
-   static electricity problems;
-   handling of loads the nature of which could lead to dangerous situations (e.g. molten metal, acids/bases, radiating materials, especially brittle loads);
-   hazards occurring during installation, transportation, decommissioning;
-   hazards occurring when handling suspended loads which can swing freely;
-   requirement related to the use on public roads;
-   wind pressure in and out of use;
-   direct contact with foodstuffs;
-   earthquake;
-   lightning.
This document is not applicable to tail lifts manufactured before the publication of this document.

  • Standard
    79 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1808:2015(Main)
Safety requirements for suspended access equipment - Design calculations, stability criteria, construction - Examinations and tests
SIST EN 1808:2015

1.1   Application
This European Standard specifies the requirements, test methods, marking and information to be provided by the manufacturer/supplier for Suspended Access Equipment (SAE).
It is applicable to both permanent and temporary equipment which may be powered or hand operated and which are defined in Clause 3.
The requirements of this standard include the rails, tracks and other support systems on which SAE depend for their integrity and safety as well as taking into account all associated loads and fixings to the building structure.
This document is not applicable to Suspended Access Equipment which is manufactured before the date of its publication as EN.
1.2   Hazards
This European Standard deals with significant hazards pertinent to SAE when they are used as intended and under the conditions foreseen by the manufacturer (see Clause 4). This European Standard specifies appropriate technical measures to eliminate or reduce risks arising from the significant hazards.
1.3   Exclusions
The following are not covered in this document:
a)   operation in severe and special conditions (e.g. extreme environmental conditions, corrosive environments, strong magnetic fields);
b)   operation subject to special rules (e.g. potentially explosive atmospheres, work on live overhead electrical lines);
c)   transportation of passengers from one level to another;
d)   handling of loads which could lead to a dangerous situation (e.g. molten metal, acids/bases, radioactive materials);
e)   working platforms suspended by cranes;
f)   silo access equipment;
g)   SAE using chains for the direct suspension of a platform;
h)   SAE using fibre ropes for the suspension of a platform;
i)   SAE intended to be used underground;
j)   SAE intended to be used in shafts;
k)   SAE directly powered by combustion engines.

  • Standard
    131 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1570-1:2011+A1:2014(Main)
Safety requirements for lifting tables - Part 1: Lifting tables serving up to two fixed landings
SIST EN 1570-1:2012+A1:2014

1.1   This European Standard specifies the safety requirements for industrial lifting tables for raising and/or lowering goods and the operator(s):
-   where the lifting table does not pass a fixed landing;
-   serving not more than 2 fixed landings.
1.2   This European Standard deals with all significant hazards pertinent to lifting tables when they are used as intended by the operating instructions and under the conditions foreseen (including foreseeable misuse) with the operating instructions (see Clause 4). This European Standard specifies the appropriate technical measures to eliminate or reduce the risks arising from the significant hazards.
1.3   Both power operated and manually operated lifting tables are included whether stationary or mobile.
1.4    This European Standard does not apply to the following equipment:
-   lifting tables, serving more than 2 fixed landings of a building, for lifting goods with a vertical travel speed not exceeding 0,15 m/s (EN 1570-2);
-   lifting tables, serving more than 2 fixed landings of a building for lifting operators, with a vertical travel speed not exceeding 0,15 m/s (EN 1570-3);
-   lifting tables carrying operators and installed in full enclosures (EN 1570-3);
-   permanently and temporarily installed lifting tables, serving specific levels of a building for lifting operators, with a vertical travel speed exceeding 0,15 m/s (EN 81-1 and EN 81-2);
-   lifting tables with flat or toothed belts lifting systems for the carrying of operators;
-   lifting tables whose vertical travel speed exceeds 0,15 m/s (unless safe by position and non person carrying);
-   power operated lifting platforms for persons with impaired mobility (EN 81-41);
-   mobile lifting tables for airport ground support equipment (EN 1915-2 and EN 12312 1);
-   lifting tables which are designed as part of a lift according to Directive (95/16/EC);
-   lifting tables used on ships;
-   mobile elevating work platforms (EN 280);
-   static elevating work platforms;
-   vehicle lifts for maintenance (EN 1493);
-   mobile lifting tables used for fire fighting (EN 1777);
-   mobile lifting tables used as fork lift trucks and order pickers;
-   mobile lifting tables with a horizontal travelling speed of more than 1,6 m/s;
-   rail dependent storage and retrieval equipment (EN 528);
-   theatre stage lifts intended to move performers;
-   scissor lift pallet trucks (EN ISO 3691 5);
-   suspended lifting tables;
-   lifting tables operated by pushing chains.
1.5   This standard does not establish the additional requirements for:
-   electromagnetic compatibility;
-   operation in severe conditions (e.g. extreme climates, freezer applications, strong magnetic fields);
-   operation subject to special rules (e.g. potentially explosive atmospheres, mines);
-   handling of loads, the nature of which could lead to dangerous situations (e.g. molten metal, acids, radiating materials, especially brittle loads);
-   hazards occurring during construction, transportation and disposal;
-   equipment installed on the load platform or replacing it;
-   integration into systems or other machines, control from more than two control stations, etc.;
-   cable-less controls;
-   lifting tables where the hydraulic pressure is derived directly from gas pressure;
-   the power supply to the lifting table by internal combustion engine.

  • Standard
    66 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1495:1997+A2:2009/AC:2010(Corrigendum)
Lifting platforms - Mast climbing work platforms
SIST EN 1495:1999+A2:2010/AC:2010

TC - Modifications on the English mother version and on the French reference version regarding formulae in Subclause A.1.1.2.
2013: Originator of XML version: first setup pilot of CCMC in 2012

  • Corrigendum
    2 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1756-2:2004+A1:2009(Main)
Tail lifts - Platform lifts for mounting on wheeled vehicles - Safety requirements - Part 2: Tail lifts for passengers
SIST EN 1756-2:2004+A1:2010

Part 2 of standard EN 1756 specifies safety requirements for design of tail lifts as defined in 3.1 for mounting on wheeled passenger vehicles.
Vehicles for the loading of disabled passengers onto aircraft and ships are included within the scope of the standard (although dock-mounted lifts are excluded).
It also specifies the verification of such tail lifts and the safety information that shall be provided for their use.
This document deals with the technical requirements to minimise the hazards listed in clause 4 which can arise during the operation of tail lifts when carried out in accordance with the specifications as intended by the manufacturer or his authorised representative.
It applies to passenger tail lifts:
-   used for the purpose of embarking and/or disembarking passengers to and from such vehicles;
-   intended to be fitted, temporarily or permanently, either inside or on the front, side or rear of the wheeled vehicle;
-   driven either by hand or by electric power;
-   equipped with a platform to support passengers who may be pedestrians or riders in wheelchairs and may be accompanied by an attendant.
Embarking and/or disembarking operations include the use of a tail lift to lift and/or lower passengers, and if specifically approved by the manufacturer, for use as a link bridge.
The standard covers the significant hazards which could occur when a tail lift is used as intended and under the conditions foreseen by the manufacturer.  A list of significant hazards is given in clause 4.
This document is not applicable to tail lifts which are manufactured before the date of publication of this document by CEN.

  • Standard
    61 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14010:2003+A1:2009(Main)
Safety of machinery - Equipment for power driven parking of motor vehicles - Safety and EMC requirements for design, manufacturing, erection and commissioning stages
SIST EN 14010:2004+A1:2010

1.1   This European Standard deals with the technical requirements to minimise the risks due to the hazards listed in clause 4, which can arise during installation , operation and maintenance of permanently installed equipment and systems for the power driven parking of motor vehicles, as defined in 3.1 to 3.4 below. Requirements are also given on the provision of information for use, which includes requirements for the drafting of the instructions. Electromagnetic compatibility requirements are also covered.
1.2   This European Standard applies to equipment and systems for the power driven parking of motor vehicles which have four wheels, are within a maximum size envelope of 5,30 m long, by 2,30 m wide, by 2,20 m high and have a mass less than 2500 kg. The equipment can be manually or automatically controlled.
1.3   This standard does not cover:
a)   vehicle lifts (see EN 1493);
b)   peripheral devices, which do not handle motor vehicles, e.g. parking meters, ticket machines;
c)   requirements related to the building even if they support directly stored vehicles;
d)   goods only lifts in accordance with EN 81-31;
e)   power driven parking equipment intended for lifting and/or transporting any person;
f)   transmission and interface of remote controls;
g)   automatic parking equipment with transfer areas which move;
h)   the use of power driven parking equipment by wheelchair users and deaf persons;
i)   the workplace of any attendant.
1.4   This standard does not deal with the following:
a)   hazards arising if loads, or other items fall from vehicles;
b)   hazards arising if fuel or oil leaks from vehicles;
c)   hazards caused by operating the equipment/system in electromagnetic fields outside the range of
EN 61000-6-2;
d)   hazards caused by operating the equipment/system in areas subject to special regulations (e.g. explosive atmospheres, fire risks);
e)   hazards caused by the use of dangerous/toxic materials, e.g. special hydraulic oil;
f)   hazards caused by noise;
g)   (....)

  • Standard
    59 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1495:1997+A2:2009(Main)
Lifting platforms - Mast climbing work platforms
SIST EN 1495:1999+A2:2010

This standard specifies the special safety requirements for Mast Climbing Work Platforms (MCWP) which are temporarily installed and are manuelly or power operated and which are designed to be used by one or more persons from which to carry out work. The vertical moving components (work platform) are also used to move those same persons and their equipmenet and materials to and from a single boarding point. These restrictions differentiate MCWPs from Builder's hoists.

  • Standard
    72 pages
    English language
    sale 10% off
    e-Library read for
    1 day