prEN 1459-7

Rough-terrain trucks - Safety requirements and verification - Part 7: Test method and determination of noise emission

This European Standard specifies the noise emission measurement methods and the configuration and conditions that are intended to be used for the tests in order to define:
-   the Sound Power Level (LWA) of the truck; and
-   the Sound Pressure Level (LpA) at the operator’s position.
This European Standard applies to:
-   rough-terrain variable-reach trucks covered by EN 1459-1; and
-   slewing rough-terrain variable-reach trucks covered by EN 1459-2.
It is intended that these tests and measurements are conducted on new machines, taken from the production line.
This standard applies to trucks manufactured after the date of publication.

Geländegängige Stapler - Sicherheitstechnische Anforderungen und Verifizierung - Teil 7: Testmethode und Bestimmung von Geräuschemissionen

Diese Europäische Norm legt ein Verfahren für die Messung der Geräuschemission und die Konfiguration und Bedingungen für die Prüfungen fest, um Folgendes zu bestimmen:
-   den Schallleistungspegel (LWA) des Staplers; und
-   den Schalldruckpegel (LpA) an der Position des Fahrers
Diese Europäische Norm gilt für:
-   geländegängige Stapler mit veränderlicher Reichweite abgedeckt durch EN 1459-1; und
-   geländegängige schwenkbare Stapler mit veränderlicher Reichweite abgedeckt durch EN 1459-1.
Es ist beabsichtigt, diese Prüfungen und Messungen an neuen Maschinen, die der Fertigungsstraße entnommen wurden, durchzuführen.
Diese Norm gilt für nach dem Datum der Veröffentlichung hergestellte Stapler.

Chariots tout-terrain - Prescriptions de sécurité et vérification - Partie 7 : Partie 7 : Méthode d'essai et détermination de l'émission sonore

La présente Norme européenne spécifie les méthodes de mesurage de l’émission sonore ainsi que la configuration et les conditions qu’il est prévu d’utiliser pour les essais afin de définir :
-   le niveau de puissance acoustique (LWA) du chariot ; et
-   le niveau de pression acoustique (LpA) au poste de conduite.
La présente Norme européenne s’applique :
-   aux chariots tout-terrain à portée variable couverts par l’EN 1459-1 ; et
-   aux chariots tout-terrain à portée variable rotatifs couverts par l’EN 1459-2.
Il est prévu de réaliser ces essais et ces mesurages sur des machines neuves, prélevées sur la chaîne de production.
La présente norme s’applique aux chariots fabriqués après la date de publication.

Vozila za talni transport - Terenska vozila - Varnostne zahteve in preverjanje - 7. del: Preskusna metoda in določanje emisije hrupa

General Information

• Status: Not Published
• Publication Date: 21-Jan-2019
• ICS: 13.040.50 - Transport exhaust emissions
• ICS: 53.060 - Industrial trucks
• Technical Committee: CEN/TC 150 - Industrial trucks - Safety
• Drafting Committee: CEN/TC 150/WG 2 - Variable reach trucks
• Current Stage: 5098 - Decision to abandon - Formal Approval
• Completion Date: 17-Dec-2018
• Directive: 2006/42/EC - Directive 2006/42/EC of the European Parliament and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast)
• Mandate: M/396 - Mandate to CEN and Cenelec for standardisation in the field of machinery
• Ref Project: oSIST prEN 1459-7:2018 - Rough-terrain trucks - Safety requirements and verification - Part 7: Test method and determination of noise emission

Standards Content (Sample)

SLOVENSKI STANDARD
01-januar-2018
9R]LOD]DWDOQLWUDQVSRUW7HUHQVNDYR]LOD9DUQRVWQH]DKWHYHLQSUHYHUMDQMH
GHO3UHVNXVQDPHWRGDLQGRORþDQMHHPLVLMHKUXSD
Rough-terrain trucks - Safety requirements and verification - Part 7: Test method and
determination of noise emission
Geländegängige Stapler - Sicherheitstechnische Anforderungen und Verifizierung - Teil
7: Testmethode und Bestimmung von Geräuschemissionen
Chariots tout-terrain - Prescriptions de sécurité et vérification - Partie 7 : Partie 7 :
Méthode d'essai et détermination de l'émission sonore
Ta slovenski standard je istoveten z: prEN 1459-7
ICS:
17.140.30 Emisija hrupa transportnih Noise emitted by means of
sredstev transport
53.060 Industrijski tovornjaki Industrial trucks
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

DRAFT
EUROPEAN STANDARD
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2017
ICS 13.040.50; 53.060
English Version
Rough-terrain trucks - Safety requirements and
verification - Part 7: Test method and determination of
noise emission
Chariots tout-terrain - Prescriptions de sécurité et Geländegängige Stapler - Sicherheitstechnische
vérification - Partie 7 : Partie 7 : Méthode d'essai et Anforderungen und Verifizierung - Teil 7: Testmethode
détermination de l'émission sonore und Bestimmung von Geräuschemissionen
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 150.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 1459-7:2017 E
worldwide for CEN national Members.

Contents Page
European foreword . 4
Introduction . 5
1 Scope . 7
2 Normative references . 7
3 Terms and definitions . 8
4 Safety requirements . 8
4.1 Instrumentation . 8
4.1.1 General . 8
4.1.2 Calibration . 8
4.2 Test environment . 8
4.2.1 General . 8
4.2.2 Test site and environmental correction, K . 8
2A
4.2.3 Background noise correction, K . 9
1A
4.2.4 Climatic conditions . 9
4.3 Measurement of A-weighted sound power level . 9
4.3.1 General . 9
4.3.2 Dimension of measurement area . 10
4.3.3 Microphone positions on the hemispherical measurement area . 10
4.4 Measurement of the A-weighted emission sound pressure level at workstations . 11
4.4.1 General . 11
4.4.2 Primary operator position . 12
4.5 Operating conditions . 12
4.5.1 General . 12
4.5.2 Positioning the truck . 12
4.5.3 Set-up and operation of the truck . 13
4.5.4 Specifications for the cab . 13
5 Verification . 14
5.1 Test procedure . 14
5.1.1 Lifting. 14
5.1.2 Travelling . 14
5.1.3 Slewing . 14
5.1.4 Operator’s position . 14
5.1.5 Period of observation (measurement) . 14
5.2 Determination of the sound power level . 15
5.3 Determination of the sound pressure level . 15
6 Information for use . 15
6.1 Information to be recorded . 15
6.2 Test report . 15
6.3 Declaration of sound emission data and uncertainty . 15
Annex A (normative) Determination of the length of the machine . 19
A.1 General . 19
A.2 Length of variable-reach trucks . 19
A.3 Length of slewing variable-reach trucks . 19
Annex B (informative) List of significant hazards . 21
B.1 General . Error! Bookmark not defined.
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 2006/42/EC aimed to be covered. 22
Bibliography . 23

European foreword
This document (prEN 1459-7:2017) has been prepared by Technical Committee CEN/TC 150
“Industrial Trucks - Safety”, the secretariat of which is held by BSI.
This document is currently submitted to the CEN Enquiry.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this
document.
EN 1459, Rough-terrain trucks — Safety requirements and verification, consists of the following parts:
— Part 1: Variable-reach trucks
— Part 2: Slewing variable-reach trucks
— Part 3: Interface between the variable-reach truck and the work platform
— Part 4: Additional requirements for variable reach trucks handling suspended loads
— Part 5: Attachments and attachment interface
— Part 6: Application of EN ISO 13849-1 to slewing and non-slewing variable-reach rough-terrain trucks
(CEN/TR)
— Part 7: Test method and determination of noise emission
— Part 8: Variable-reach tractors (CEN/TS)
Introduction
This document is a type-C standard as stated in EN ISO 12100.
This document is of relevance, in particular, for the following stakeholder groups representing the
market players with regard to machinery safety:
— machine manufacturers (small, medium and large enterprises);
— health and safety bodies (regulators, accident prevention organizations, market surveillance, etc.).
Others can be affected by the level of machinery safety achieved with the means of the document by the
above-mentioned stakeholder groups:
— machine users/employers (small, medium and large enterprises);
— machine users/employees (e.g. trade unions, organizations for people with special needs);
— service providers, e.g. for maintenance (small, medium and large enterprises);
— consumers (in case of machinery intended for use by consumers).
The above-mentioned stakeholder groups have been given the possibility to participate at the drafting
process of this document.
This noise-test code specifies all the information necessary to carry out efficiently and under
standardized conditions the determination, declaration and verification of the noise-emission
characteristics of trucks.
Noise-emission characteristics include the emission sound pressure levels at workstations and the
sound power level.
The determination of those values is necessary for:
— manufacturers to declare the noise emitted from their machines;
— the design stage and to ensure conformity of production.
The test codes here described are taken from the Working Group 7 position paper – Summary of
information gathered to contribute to the Article 20 report (version NOISE/13/01/2 rev.1 adopted June
2013).
The use of these test codes ensures that the tests are conducted and the data is processed in a reliable
and reproducible manner.
Test codes defines the limits accuracies and are conducted in engineering methods (grade 2).
Main sources of noise in trucks are:
— internal combustion engine;
— hydraulic components (cylinders, pump…);
— motor fans;
— control valves;
— exhaust gas emission point;
— transmission components.
Typical measures to reduce noise at design stage are:
— selection of low noise components;
— use of exhaust silencers for engine.
Typical measures to reduce noise by protective measures are:
— the use of sound insulating covers and enclosures around noisy co
...