iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN ISO 10156:2010/AC:2010

(Corrigendum)

Gases and gas mixtures - Determination of fire potential and oxidizing ability for the selection of cylinder valve outlets - Technical Corrigendum 1 (ISO 10156:2010/Cor 1:2010)

Gases and gas mixtures - Determination of fire potential and oxidizing ability for the selection of cylinder valve outlets - Technical Corrigendum 1 (ISO 10156:2010/Cor 1:2010)

This International Standard specifies methods for determining whether or not a gas or gas mixture is flammable in air and whether a gas or gas mixture is more or less oxidizing than air under atmospheric conditions. This International Standard is intended to be used for the classification of gases and gas mixtures including the selection of gas cylinder valve outlets. This International Standard does not cover the safe preparation of these mixtures under pressure and at temperatures other than ambient.

Gase und Gasgemische - Bestimmung der Brennbarkeid und des Oxidationsvermögens zur Auswahl von Ventilausgängen (ISO 10156:2010/Cor 1:2010)

Gaz et mélanges de gaz - Détermination du potentiel d'inflammabilité et d'oxydation pour le choix des raccords de sortie de robinets - Rectificatif technique 1 (ISO 10156:2010/Cor 1:2010)

Plini in zmesi plinov - Določitev stopnje gorljivosti in oksidativnosti za izbiro izhodnega priključka ventila na jeklenki - Popravek AC (ISO 10156:2010/Cor 1:2010)

Ta mednarodni standard opredeljuje metode za določevanje ali je ali ni plin ali zmes plina gorljiva na zraku in ali je plin ali zmes plina bolj oksidativna kot zrak v atmosferskih pogojih. Ta mednarodni standard je namenjen temu, da se uporablja za klasifikacijo plinov in zmesi plinov, vključno z izbiro izhodnega priključka ventila na jeklenki. Ta mednarodni standard ne zajema varne priprave teh zmesi pod tlakom in pri temperaturi, ki nista okoljska.

General Information

Status
Withdrawn
Publication Date
13-Jul-2010
Withdrawal Date
29-Aug-2017
ICS
23.020.30 - Pressure vessels, gas cylinders
23.020.35 - Gas cylinders
71.100.20 - Gases for industrial application
Technical Committee
CEN/TC 23 - Transportable gas cylinders
Drafting Committee
CEN/TC 23/SC 2 - Fittings
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
30-Aug-2017
Directive
2008/68/EC - Directve 2008/68/EC of the European Parliament and of the council of 24 September 2008 on the inland transport of the dangerous goods
Mandate
M/086 - Mandate to CEN for standardization in the field of transport of dangerous goods
Ref Project
SIST EN ISO 10156:2010/AC:2010 - Gases and gas mixtures - Determination of fire potential and oxidizing ability for the selection of cylinder valve outlets - Technical Corrigendum 1 (ISO 10156:2010/Cor 1:2010)

Relations

Replaced By
EN ISO 10156:2017 - Gas cylinders - Gases and gas mixtures - Determination of fire potential and oxidizing ability for the selection of cylinder valve outlets (ISO 10156:2017)
Effective Date
06-Sep-2017
Corrects
EN ISO 10156:2010 - Gases and gas mixtures - Determination of fire potential and oxidizing ability for the selection of cylinder valve outlets (ISO 10156:2010)
Effective Date
08-Jun-2022

Buy Standard

EN ISO 10156:2010/AC:2010EN ISO 10156:2010/AC:2010
PreviousNext
Corrigendum
EN ISO 10156:2010/AC:2010
English language
4 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.&RUGase und Gasgemische - Bestimmung der Brennbarkeid und des Oxidationsvermögens zur Auswahl von Ventilausgängen (ISO 10156:2010/Cor 1:2010)Gaz et mélanges de gaz - Détermination du potentiel d'inflammabilité et d'oxydation pour le choix des raccords de sortie de robinets - Rectificatif technique 1 (ISO 10156:2010/Cor 1:2010)Gases and gas mixtures - Determination of fire potential and oxidizing ability for the selection of cylinder valve outlets - Technical Corrigendum 1 (ISO 10156:2010/Cor 1:2010)71.100.20Industrijski pliniGases for industrial application23.020.30MHNOHQNHPressure vessels, gas cylindersICS:Ta slovenski standard je istoveten z:EN ISO 10156:2010/AC:2010SIST EN ISO 10156:2010/AC:2010en,fr01-november-2010SIST EN ISO 10156:2010/AC:2010SLOVENSKI
STANDARD



SIST EN ISO 10156:2010/AC:2010



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN ISO 10156:2010/AC
July 2010
Juillet 2010
Juli 2010 ICS 23.020.30; 71.100.20 English version Version Française Deutsche Fassung
Gases and gas mixtures - Determination of fire potential and oxidizing ability for the selection of cylinder valve outlets - Technical Corrigendum 1 (ISO 10156:2010/Cor 1:2010)
Gaz et mélanges de gaz - Détermination du potentiel d'inflammabilité et d'oxydation pour le choix des raccords de sortie de robinets - Rectificatif technique 1 (ISO 10156:2010/Cor 1:2010)
Gase und Gasgemische - Bestimmung der Brennbarkeid und des Oxidationsvermögens zur Auswahl von Ventilausgängen (ISO 10156:2010/Cor 1:2010) This corrigendum becomes effective on 14 July 2010 for incorporation in the three official language versions of the EN.
Ce corrigendum prendra effet le 14 juillet 2010 pour incorporation dans les trois versions linguistiques officielles de la EN.
Die Berichtigung tritt am 14.Juli 2010 zur Einarbeitung in die drei offiziellen Sprachfassungen der EN in Kraft.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2010 CEN All rights of exp
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 10156:2017(Main)
Gas cylinders - Gases and gas mixtures - Determination of fire potential and oxidizing ability for the selection of cylinder valve outlets (ISO 10156:2017)
SIST EN ISO 10156:2018

ISO 10156:2017 specifies methods for determining whether or not a gas or gas mixture is flammable in air and whether a gas or gas mixture is more or less oxidizing than air under atmospheric conditions.
ISO 10156:2017 is intended to be used for the classification of gases and gas mixtures including the selection of gas cylinder valve outlets.
ISO 10156:2017 does not cover the safe preparation of these mixtures under pressure and at temperatures other than ambient.

  • Standard
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 720-1:1999(Main)
Transportable gas cylinders - Gases and gas mixtures - Part 1: Properties of pure gases
SIST EN 720-1:2000

The purpose of this part of EN 720 is to define the properties of gases on the basis of four main physical - chemical criteria, i.e. fire potential, toxicity, state of gas and corrosiveness for the purpose of the selection of suitable valve outlets.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 10156:2017(Main)
Gas cylinders - Gases and gas mixtures - Determination of fire potential and oxidizing ability for the selection of cylinder valve outlets (ISO 10156:2017)
SIST EN ISO 10156:2018

ISO 10156:2017 specifies methods for determining whether or not a gas or gas mixture is flammable in air and whether a gas or gas mixture is more or less oxidizing than air under atmospheric conditions.
ISO 10156:2017 is intended to be used for the classification of gases and gas mixtures including the selection of gas cylinder valve outlets.
ISO 10156:2017 does not cover the safe preparation of these mixtures under pressure and at temperatures other than ambient.

  • Standard
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 720-1:1999(Main)
Transportable gas cylinders - Gases and gas mixtures - Part 1: Properties of pure gases
SIST EN 720-1:2000

The purpose of this part of EN 720 is to define the properties of gases on the basis of four main physical - chemical criteria, i.e. fire potential, toxicity, state of gas and corrosiveness for the purpose of the selection of suitable valve outlets.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 22435:2024(Main)
Gas cylinders - Cylinder valves with integrated pressure regulators - Specification and type testing (ISO 22435:2024)
kSIST FprEN ISO 22435:2024

This document specifies design, type test methods, marking and instruction requirements for cylinder valves with integrated pressure regulators (VIPRs) intended to be fitted to gas cylinders, pressure drums or tubes or used as a main valve for bundles of cylinders that convey compressed, liquefied or dissolved gases.
These are requirements for VIPRs that are in addition to those given in the relevant closure standard, for example, in ISO 10297 for cylinder valves, in ISO 17871 for quick-release cylinder valves, in ISO 17879 for self-closing cylinder valves or in ISO 23826 for ball valves. For ISO 17871, these requirements are only applicable to quick-release cylinder valves types B, C, D and E.
NOTE 1        If the pressure regulating system of a VIPR is acting as the primary valve operating mechanism, it is covered by the relevant closure standard, e.g. ISO 10297, ISO 17871, ISO 17879 and ISO 23826. This also includes designs where closure of the primary valve operating mechanism of a VIPR is obtained by closing the seat of the pressure regulating system.
NOTE 2        If the primary valve operating mechanism of a VIPR is located at the low-pressure side of the pressure regulating system, it is covered by the relevant closure standard, e.g. ISO 10297, ISO 17871, ISO 17879 and ISO 23826.
NOTE 3        The term “pressure receptacle” is used within this document to cover instances where no differentiation is necessary between gas cylinders, bundles of cylinders, pressure drums and tubes.
This document does not apply to VIPRs for
a)       medical applications (see ISO 10524-3);
b)       liquefied petroleum gas (LPG);
c)        cryogenic applications.
NOTE 4        Additional requirements for a VIPR with a residual pressure device (RPD) are specified in ISO 15996.
NOTE 5        Additional requirements for pressure relief valves can exist in international/regional regulations/ standards.

  • Draft
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17015-1:2024(Main)
Electronic Public Procurement - Catalogue - Part 1: Choreographies
kSIST FprEN 17015-1:2024

The purpose of this deliverable is to specify and describe choreographies for exchanging an electronic product catalogue (“catalogues”) as part of the business processes in the pre-award and post-award area, so that catalogues can serve as a basis for placing orders as well as evaluating tenders. The key aspects covered by this choreography specification are:
-   processes for submitting catalogues from the selling to the buying side;
-   processes for submitting catalogue-related data as part of a tendering process;
-   processes integrating sell-side procurement systems.
This document does not apply to the transactions used in the specified choreographies. These transactions are specified in EN 17015 2. The relationship between the choreographies and the transaction is described in Clause 8.
The identifier of this choreographies document is EN 17015 1:2024.
How to claim compliance to this choreography is specified in 6.2.3.

  • Draft
    38 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO/ASTM 52927:2024(Main)
Additive manufacturing - General principles - Main characteristics and corresponding test methods (ISO/ASTM 52927:2024)
kSIST FprEN ISO/ASTM 52927:2024

This document specifies the principal requirements applied to the testing of parts produced by additive manufacturing processes.
This document
—     identifies quality characteristics for feedstock and parts and the corresponding test procedures,
—     provides the specific procedures to build specimens using additive manufacturing process, and
—     recommends the scope and content of test and supply agreements.
This document is aimed at machine manufacturers, feedstock suppliers, AM system users, part providers, and customers to facilitate the communication on main quality characteristics. It applies wherever additive manufacturing processes are used.
NOTE            It is the intent to include, in future versions of this document, other characteristics such as thermal properties, electrical requirements and physical and physico-chemical properties based upon material types.

  • Draft
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 8362-2:2024(Main)
Injection containers and accessories - Part 2: Closures for injection vials (ISO 8362-2:2024)
SIST EN ISO 8362-2:2024

This document specifies the shape, dimensions, material, performance requirements and labelling of closures for injection vials covered by ISO 8362-1 and ISO 8362-4.
The dimensional requirements are not applicable to barrier-coated closures.
Closures specified in this document are intended for single use only.
NOTE            The potency, purity, stability and safety of a medicinal product during its manufacture and storage can strongly be affected by the nature and performance of the primary packaging.

  • Draft
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 16739-1:2024(Main)
Industry Foundation Classes (IFC) for data sharing in the construction and facility management industries - Part 1: Data schema (ISO 16739-1:2024)
kSIST FprEN ISO 16739-1:2024

This document represents an open international standard for information used in Building Information Modeling (BIM) that is exchanged and shared among software applications used by the various participants in the construction or facility management industry sector. This document includes definitions that cover information required for buildings and infrastructure works over their life cycle. This edition of the document added coverage of information required for infrastructure facilities including bridges, roads, railways, waterways and port facilities.
This document comprises the publication of a data schema, its documentation, the property and quantity set definitions and the mechanism of an exchange file format structure.
Definitions from this document are used to support different recognized work flows in the construction and facility management industry sector, representing information deliveries. Such information deliveries can be described according to ISO 29481.
Different implementation levels of this document can be defined to better support multiple information deliveries, they are referred to as a Model View Definition (MVD). Each MVD identifies which subset of the definitions of this document imposes requirements for implementation in software applications. Conforming software applications need to identify the model view definition they conform to when applying for software certification.
The following are within the scope of this edition of this document:
BIM exchange format definitions that are required during the life cycle phases of buildings and infrastructure:
demonstrating the need;
conception of need;
outline feasibility;
substantive feasibility study and outline financial authority;
outline conceptual design;
full conceptual design;
coordinated design;
procurement and full financial authority;
production information;
construction;
operation and maintenance.
BIM exchange format definitions that are required by the various disciplines involved within the life cycle phases:
architecture and civil engineering design;
service and utilities engineering;
structural engineering;
procurement;
construction planning;
facility and utility management;
project management;
client requirement management;
industry authorities for permits and approval.
BIM exchange format definitions including:
project structure;
physical components;
spatial components;
analysis items;
processes;
resources;
controls;
actors;
context definition.

  • Draft
    406 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 2620:2024(Main)
Analysis of natural gas - Biomethane - Determination of VOCs by thermal desorption gas chromatography with flame ionization and/or mass spectrometry detectors (ISO 2620:2024)
kSIST FprEN ISO 2620:2024

This document describes a method for sampling and analysis of volatile organic compounds (VOCs), including siloxanes, terpenes, organic sulfur compounds, in natural gas and biomethane matrices, using thermal desorption gas chromatography with flame ionization and/or mass spectrometry detectors (TD-GC-FID/MS).

  • Draft
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day