EN ISO 10510:2011
(Main)Tapping screw and washer assemblies with plain washers (ISO 10510:2011)
Tapping screw and washer assemblies with plain washers (ISO 10510:2011)
ISO 10510:2011 specifies the requirements for tapping screws and plain washer assemblies with spaced threads from ST2,2 to ST9,5 inclusive, flat seating heads and mechanical properties as specified in ISO 2702.
Kombi-Blechschrauben mit flachen Scheiben (ISO 10510:2011)
Diese Internationale Norm legt Anforderungen für Kombi-Blechschrauben mit Blechschraubengewinden von ST2,2 bis ST9,5, mit flach aufliegenden Köpfen und mechanischen Eigenschaften nach ISO 2702 fest.
Die flachen Scheiben sind unverlierbar und können sich frei drehen.
Vis à tôle à rondelle plate imperdable (ISO 10510:2011)
L'ISO 10510:2011 spécifie les caractéristiques des vis à tôle à rondelle plate imperdable de diamètre de filetage ST2,2 à ST9,5 inclus, présentant une surface d'appui plane, et dont les caractéristiques mécaniques sont conformes à l'ISO 2702.
Pločevinski vijaki z ujeto podložko (ISO 10510:2011)
ISO 10510:2010 določa zahteve za pločevinaste vijake z ujeto podložko in razmiki navojev med ST2,2 do vključno ST9,5, s ploščato glavo in mehanskimi lastnostmi, kot jih določa ISO 2702.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 10510:2011
01-november-2011
1DGRPHãþD
SIST EN ISO 10510:2001
3ORþHYLQVNLYLMDNL]XMHWRSRGORåNR ,62
Tapping screw and washer assemblies with plain washers (ISO 10510:2011)
Kombi-Blechschrauben mit flachen Scheiben (ISO 10510:2011)
Vis à tôle à rondelle plate incorporée (ISO 10510:2011)
Ta slovenski standard je istoveten z: EN ISO 10510:2011
ICS:
21.060.10 Sorniki, vijaki, stebelni vijaki Bolts, screws, studs
SIST EN ISO 10510:2011 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 10510:2011
---------------------- Page: 2 ----------------------
SIST EN ISO 10510:2011
EUROPEAN STANDARD
EN ISO 10510
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2011
ICS 21.060.10 Supersedes EN ISO 10510:1999
English Version
Tapping screw and washer assemblies with plain washers (ISO
10510:2011)
Vis à tôle à rondelle plate imperdable (ISO 10510:2011) Kombi-Blechschrauben mit flachen Scheiben (ISO
10510:2011)
This European Standard was approved by CEN on 17 January 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10510:2011: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 10510:2011
EN ISO 10510:2011 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 10510:2011
EN ISO 10510:2011 (E)
Foreword
This document (EN ISO 10510:2011) has been prepared by Technical Committee ISO/TC 2 "Fasteners" in
collaboration with Technical Committee CEN/TC 185 “Fasteners” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by October 2011, and conflicting national standards shall be withdrawn at
the latest by October 2011.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 10510:1999.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 10510:2011 has been approved by CEN as a EN ISO 10510:2011 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 10510:2011
---------------------- Page: 6 ----------------------
SIST EN ISO 10510:2011
INTERNATIONAL ISO
STANDARD 10510
Second edition
2011-04-01
Tapping screw and washer assemblies
with plain washers
Vis à tôle à rondelle plate imperdable
Reference number
ISO 10510:2011(E)
©
ISO 2011
---------------------- Page: 7 ----------------------
SIST EN ISO 10510:2011
ISO 10510:2011(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.