EN ISO 15527:2018

Plastics - Compression-moulded sheets of polyethylene (PE-UHMW, PE-HD) - Requirements and test methods (ISO 15527:2018)

This document specifies the requirements and test methods for solid flat compression-moulded sheets of polyethylene (PE-UHMW and PE-HD, see ISO 1043-1) without fillers or reinforcing materials. It applies only to thicknesses from 10 mm to 200 mm.

Kunststoffe - Gepresste Tafeln aus Polyethylen (PE-UHMW, PE-HD) - Anforderungen und Prüfverfahren (ISO 15527:2018)

Dieses Dokument legt die Anforderungen und Prüfverfahren an massive ebene gepresste Tafeln aus Polyethylen (PE UHMW und PE HD, siehe ISO 1043 1) ohne Füll- oder Verstärkungsstoffe fest. Sie gilt nur für Tafeldicken von 10 mm bis 200 mm.

Plastiques - Plaques moulées par compression en polyéthylène (PE-UHMW, PE-HD) - Exigences et méthodes d'essai (ISO 15527:2018)

Le présent document spécifie les exigences et les méthodes d'essai pour les plaques moulées par compression, compactes et planes, en polyéthylène (PE-UHMW et PE-HD, voir l'ISO 1043-1) sans charges ou matériaux de renforcement. Il s'applique uniquement aux plaques de 10 mm à 200 mm d'épaisseur.

Polimerni materiali - Kompresijsko brizgane polietilenske plošče (PE-UHMW, PE-HD) - Zahteve in preskusne metode (ISO 15527:2018)

Ta dokument določa zahteve in preskusne metode za masivne ravne kompresijsko brizgane polietilenske plošče (PE-UHMW in PE-HD, glej standard ISO 1043-1) brez polnil ali materialov za ojačanje. Uporablja se le za debeline od 10 mm do 200 mm.

General Information

• Status: Withdrawn
• Publication Date: 11-Dec-2018
• Withdrawal Date: 22-Feb-2022
• ICS: 83.140.10 - Films and sheets
• Technical Committee: CEN/TC 249 - Plastics
• Drafting Committee: CEN/TC 249 - Plastics
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Completion Date: 23-Feb-2022
• Ref Project: SIST EN ISO 15527:2019 - Plastics - Compression-moulded sheets of polyethylene (PE-UHMW, PE-HD) - Requirements and test methods (ISO 15527:2018)

Relations

• Replaces: EN ISO 15527:2013 - Plastics - Compression-moulded sheets of polyethylene (PE-UHMW, PE-HD) - Requirements and test methods (ISO 15527:2010)
• Effective Date: 09-Dec-2015
• Replaced By: EN ISO 15527:2022 - Plastics - Compression-moulded sheets of polyethylene (PE-UHMW, PE-HD) - Requirements and test methods (ISO 15527:2022)
• Effective Date: 04-Nov-2020

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 15527:2019
01-februar-2019
1DGRPHãþD
SIST EN ISO 15527:2013
3ROLPHUQLPDWHULDOL.RPSUHVLMVNREUL]JDQHSROLHWLOHQVNHSORãþH3(8+0:3(
+'=DKWHYHLQSUHVNXVQHPHWRGH,62
Plastics - Compression-moulded sheets of polyethylene (PE-UHMW, PE-HD) -
Requirements and test methods (ISO 15527:2018)
Kunststoffe - Gepresste Tafeln aus Polyethylen (PE-UHMW, PE-HD) - Anforderungen
und Prüfverfahren (ISO 15527:2018)
Plastiques - Plaques moulées par compression en polyéthylène (PE-UHMW, PE-HD) -
Exigences et méthodes d'essai (ISO 15527:2018)
Ta slovenski standard je istoveten z: EN ISO 15527:2018
ICS:
83.140.10 Filmi in folije Films and sheets
SIST EN ISO 15527:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 15527:2019

---------------------- Page: 2 ----------------------

SIST EN ISO 15527:2019


EN ISO 15527
EUROPEAN STANDARD

NORME EUROPÉENNE

December 2018
EUROPÄISCHE NORM
ICS 83.140.10 Supersedes EN ISO 15527:2013
English Version

Plastics - Compression-moulded sheets of polyethylene
(PE-UHMW, PE-HD) - Requirements and test methods (ISO
15527:2018)
Plastiques - Plaques moulées par compression en Kunststoffe - Gepresste Tafeln aus Polyethylen (PE-
polyéthylène (PE-UHMW, PE-HD) - Exigences et UHMW, PE-HD) - Anforderungen und Prüfverfahren
méthodes d'essai (ISO 15527:2018) (ISO 15527:2018)
This European Standard was approved by CEN on 4 November 2018.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15527:2018 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 15527:2019
EN ISO 15527:2018 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 15527:2019
EN ISO 15527:2018 (E)
European foreword
This document (EN ISO 15527:2018) has been prepared by Technical Committee ISO/TC 61 "Plastics"
in collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by
NBN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by June 2019, and conflicting national standards shall be
withdrawn at the latest by June 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 15527:2013.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 15527:2018 has been approved by CEN as EN ISO 15527:2018 without any modification.

3

---------------------- Page: 5 ----------------------

SIST EN ISO 15527:2019

---------------------- Page: 6 ----------------------

SIST EN ISO 15527:2019
INTERNATIONAL ISO
STANDARD 15527
Third edition
201
...