EN ISO 23667:2007
(Main)Packaging - Transport packaging for dangerous goods - Rigid plastics and plastics composite IBCs - Compatibility testing (ISO 23667:2007)
Packaging - Transport packaging for dangerous goods - Rigid plastics and plastics composite IBCs - Compatibility testing (ISO 23667:2007)
ISO 23667:2006 specifies the requirements and test methods for compatibility testing of polyethylene-based plastics Intermediate Bulk Containers (IBCs) and composite IBCs with plastics inners containing liquids. The testing involves storage with the packaged substance, or with a standard liquid as defined in Annex A. Annex B describes small scale laboratory tests, which may be used to determine the assimilation of those products to be carried with the standard liquids.
Verpackung - Verpackungen zur Beförderung gefährlicher Güter - Starre Kunststoff-IBC und Kombinations-IBC mit Kunststoffinnenbehälter - Verträglichkeitsprüfung (ISO 23667:2007)
Diese Internationale Norm legt die Anforderungen an und die Verfahren für die Verträglichkeitsprüfung von auf Polyethylenbasis hergestellten Kunststoff IBC und Kombinations IBC mit Kunststoffinnenbehältern fest, die für Flüssigkeiten vorgesehen sind. Die Prüfung schließt die Lagerung mit dem Füllgut oder mit einer Standardflüssigkeit, wie sie in Anhang A definiert wird, ein. Anhang B beschreibt Prüfungen im Labormaßstab, die für die Bestimmung der Assimilierung der zu befördernden Produkte mit den Stan¬dardflüssigkeiten verwendet werden können.
Diese Internationale Norm sollte in Verbindung mit einer oder mehreren der internationalen Vorschriften, die in den Literaturhinweisen genannt sind, angewendet werden.
Emballages - Emballages de transport pour marchandises dangereuses - Grands récipients pour vrac en plastique rigide et en plastique composite - Essais de compatibilité (ISO 23667:2007)
L'ISO 23667:2006 spécifie les exigences et les méthodes d'essai pour vérifier la compatibilité des GRV en plastique à base de polyéthylène et des GRV composites dont les récipients intérieurs en plastique contiennent des liquides. L'essai implique le stockage avec la substance emballée ou avec un liquide de référence tel que défini dans l'Annexe A. L'Annexe B décrit des essais en laboratoire sur éprouvettes qui peuvent être utilisés pour déterminer l'assimilation de ces produits aux liquides de référence.
Embalaža - Transportna embalaža za nevarno blago - Togi vsebniki IBC in sestavljeni vsebniki IBC z notranjo plastično posodo - Preskušanje združljivosti (ISO 23667:2007)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-januar-2008
(PEDODåD7UDQVSRUWQDHPEDODåD]DQHYDUQREODJR7RJLYVHEQLNL,%&LQ
VHVWDYOMHQLYVHEQLNL,%&]QRWUDQMRSODVWLþQRSRVRGR3UHVNXãDQMH]GUXåOMLYRVWL
,62
Packaging - Transport packaging for dangerous goods - Rigid plastics and plastics
composite IBCs - Compatibility testing (ISO 23667:2007)
Verpackung - Verpackungen zur Beförderung gefährlicher Güter - Starre Kunststoff-IBC
und Kombinations-IBC mit Kunststoffinnenbehälter - Verträglichkeitsprüfung (ISO
23667:2007)
Emballage - Emballages d'expédition de marchandises dangereuses - Grands récipients
en vrac en plastiques rigide et en plastique composite - Essais de compatibilité (ISO
23667:2007)
Ta slovenski standard je istoveten z: EN ISO 23667:2007
ICS:
13.300 Varstvo pred nevarnimi Protection against dangerous
izdelki goods
55.180.99 Drugi standardi v zvezi z Other standards related to
distribucijo blaga s prevozom freight distribution of goods
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 23667
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2007
ICS 55.020; 13.300
English Version
Packaging - Transport packaging for dangerous goods - Rigid
plastics and plastics composite IBCs - Compatibility testing (ISO
23667:2007)
Emballages - Emballages de transport pour marchandises Verpackung - Verpackungen zur Beförderung gefährlicher
dangereuses - Grands récipients pour vrac en plastique Güter - Starre Kunststoff-IBC und Kombinations-IBC mit
rigide et en plastique composite - Essais de compatibilité Kunststoffinnenbehälter - Verträglichkeitsprüfung (ISO
(ISO 23667:2007) 23667:2007)
This European Standard was approved by CEN on 20 June 2007.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2007 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 23667:2007: E
worldwide for CEN national Members.
Foreword
This document (EN ISO 23667:2007) has been prepared by Technical Committee CEN/TC 261
"Packaging", the secretariat of which is held by AFNOR, in collaboration with Technical
Committee ISO/TC 122 "Packaging".
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by January 2008, and conflicting national
standards shall be withdrawn at the latest by January 2008.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United
Kingdom.
INTERNATIONAL ISO
STANDARD 23667
First edition
2007-07-15
Packaging — Transport packaging for
dangerous goods — Rigid plastics and
plastics composite IBCs — Compatibility
testing
Emballages — Emballages de transport pour marchandises
dangereuses — Grands récipients pour vrac en plastique rigide et en
plastique composite — Essais de compatibilité
Reference number
ISO 23667:2007(E)
©
ISO 2007
ISO 23667:2007(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2007
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2007 – All rights reserved
ISO 23667:2007(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope .1
2 Normative references .1
3 Terms and definitions .2
4 Test requirements.2
5 Selection and preparation of test IBCs.4
6 Facilities for testing.6
7 Conditioning procedures .7
Annex A (normative) Standard liquids and applicability to polyethylene types .9
Annex B (normative) Small scale laboratory tests to assess packaged substances against
standard liquids .12
Annex C (informative) Assimilation of packaged substance to standard liquids .31
Bibliography .82
ISO 23667:2007(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 23667 was prepared by the European Committee for Standardization (CEN) Technical Committee
CEN/TC 261, Packaging, in collaboration with ISO Technical Committee TC 122, Packaging, Subcommittee
SC 3, Performance requirements and tests for means of packaging, packages and unit loads (as required by
ISO/TC 122), in accordance with the Agreement on technical cooperation between ISO and CEN (Vienna
Agreement).
iv © ISO 2007 – All rights reserved
ISO 23667:2007(E)
Introduction
This International Standard was developed to provide requirements and test procedures to meet the
compatibility provisions for plastics Intermediate Bulk Containers (IBCs) to contain liquids as set out in:
⎯ the European Agreement concerning the International Carriage of Dangerous Goods by Road (ADR)
[2]
(covering most of Europe) ; and
⎯ the Regulations concerning the International Carriage of Dangerous Goods by Rail (RID) (covering most
[5]
of Europe, parts of North Africa and the Middle East) .
This procedure is an alternative option to that set out in the UN Recommendations on the Transport of
[1]
Dangerous Goods .
Plastics IBC material can be attacked by the chemical contents of the package. Such effects are caused by
different mechanisms such as environmental stress cracking (ESC), chemical degradation and swelling.
The UN recommendations and the associated modal regulations require that all IBCs shall be assessed for
compatibility with the substances which they are to contain. The UN text makes special reference to plastics
IBCs for liquids. The procedure therein contains details of testing for six months at ambient temperature with
the liquid to be carried. RID/ADR permits as an alternative the use of standard liquids to which this document
refers.
The UN recommendations are given legal entity not only to ADR and RID, but also to
[4]
⎯ the International Maritime Dangerous Goods Code (IMDG Code) (worldwide) .
These modal rules do not refer to the standard liquid tests, but they may still be acceptable as the UN
provisions do not make the six month test a mandatory requirement.
The application of this International Standard will need to take account of the requirements of these
[6], [7]
international agreements and the relevant national regulations for domestic transport of dangerous
goods.
INTERNATIONAL STANDARD ISO 23667:2007(E)
Packaging — Transport packaging for dangerous goods —
Rigid plastics and plastics composite IBCs — Compatibility
testing
WARNING — The use of this International Standard may involve hazardous materials and equipment.
This International Standard does not purport to address all of the safety problems associated with its
use. It is the responsibility of the user of this International Standard to establish appropriate safety
and health practices and determine the applicability of regulatory limitations prior to use.
1 Scope
This International Standard specifies the requirements and test methods for compatibility testing of
polyethylene-based plastics Intermediate Bulk Containers (IBCs) and composite IBCs with plastics inners
containing liquids. The testing involves storage with the packaged substance, or with a standard liquid as
defined in Annex A. Annex B describes small scale laboratory tests, which may be used to determine the
assimilation of those products to be carried with the standard liquids.
This International Standard should be used in conjunction with one or more of the international regulations set
out in the Bibliography.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 291, Plastics — Standard atmospheres for conditioning and testing
ISO 527-2, Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and
extrusion plastics
ISO 1133, Plastics — Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of
thermoplastics
ISO 1183-1, Plastics — Methods for determining the density of non-cellular plastics — Part 1: Immersion
method, liquid pyknometer method and titration method
ISO 1628-3, Plastics — Determination of the viscosity of polymers in dilute solution using capillary
viscometers — Part 3: Polyethylenes and polypropylenes
ISO 1872-2, Plastics — Polyethylene (PE) moulding and extrusion materials — Part 2: Preparation of test
specimens and determination of properties
ISO 2818, Plastics — Preparation of test specimens by machining
ISO 11403-3, Plastics — Acquisition and presentation of c
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.