EN 61212-2:2006

Insulating materials - Industrial rigid round laminated tubes and rods based on thermosetting resins for electrical purposes - Part 2: Methods of test

This part of IEC 61212 describes methods of test for the materials defined in IEC 61212-1. Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application should be based on the actual requirements necessary for adequate performance in that application and not based on this specification alone.

Isolierstoffe - Runde Rohre und Stäbe aus technischen Schichtpressstoffen auf der Basis warmhärtender Harze für elektrotechnische Zwecke - Teil 2: Prüfverfahren

Matériaux isolants - Tubes et barres industriels, rigides, ronds, stratifiés, à base de résines thermodurcissables, à usages électriques - Partie 2: Méthodes d'essai

La CEI 61212-2:2006 décrit les méthodes d'essai des matériaux définis dans la CEI 61212-1. Les matériaux qui sont conformes à cette spécification satisfont à des niveaux de performances établis. Cependant, il convient que le choix d'un matériau par un utilisateur et pour une application particulière soit fondé sur les exigences réelles nécessaires pour obtenir les performances satisfaisantes pour cette application, et non pas fondé sur cette seule spécification. Les principales modifications suivantes ont été apportées par rapport à l'édition précédente: ajout d'instructions liées à l'utilisation et à la sécurité de l'application. Le document a été reformaté pour tenir compte du format en cours des documents CEI. Les références à la méthode d'essai ont été mises à jour.

Izolacijski materiali – Industrijske toge okrogle laminirane cevi in palice na temelju termično utrjenih smol za električne namene – 2. del: Preskušalne metode (IEC 61212-2:2006)

General Information

• Status: Published
• Publication Date: 13-Dec-2006
• Withdrawal Date: 31-Oct-2009
• ICS: 29.035.01 - Insulating materials in general
• ICS: 29.040.20 - Insulating gases
• Technical Committee: CLC/SR 15 - Insulating materials
• Drafting Committee: IEC/TC 15 - IEC_TC_15
• Parallel Committee: IEC/TC 15 - IEC_TC_15
• Current Stage: 6060 - Document made available - Publishing
• Start Date: 14-Dec-2006
• Completion Date: 14-Dec-2006
• Ref Project: SIST EN 61212-2:2007 - Insulating materials - Industrial rigid round laminated tubes and rods based on thermosetting resins for electrical purposes -- Part 2: Methods of test

Relations

• Replaces: EN 61212-2:1996 - Industrial rigid round laminated tubes and rods based on thermosetting resins for electrical purposes - Part 2: Methods of test
• Effective Date: 28-Jan-2023

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 61212-2:2007
01-november-2007
1DGRPHãþD
SIST EN 61212-2:1998
,]RODFLMVNLPDWHULDOL±,QGXVWULMVNHWRJHRNURJOHODPLQLUDQHFHYLLQSDOLFHQDWHPHOMX
WHUPLþQRXWUMHQLKVPRO]DHOHNWULþQHQDPHQH±GHO3UHVNXãDOQHPHWRGH,(&

Insulating materials - Industrial rigid round laminated tubes and rods based on
thermosetting resins for electrical purposes -- Part 2: Methods of test (IEC 61212-2:2006)
Isolierstoffe - Runde Rohre und Stäbe aus technischen Schichtpressstoffen auf der Basis
warmhärtender Harze für elektrotechnische Zwecke - Teil 2: Prüfverfahren (IEC 61212-
2:2006)
Matériaux isolants - Tubes et barres industriels, rigides, ronds, stratifiés, a base de
résines thermodurcissables, a usages électriques -- Partie 2: Méthodes d'essai (IEC
61212-2:2006)
Ta slovenski standard je istoveten z: EN 61212-2:2006
ICS:
29.035.01 Izolacijski materiali na Insulating materials in
splošno general
SIST EN 61212-2:2007 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

EUROPEAN STANDARD
EN 61212-2

NORME EUROPÉENNE
December 2006
EUROPÄISCHE NORM

ICS 29.035.01 Supersedes EN 61212-2:1996


English version


Insulating materials -
Industrial rigid round laminated tubes and rods
based on thermosetting resins for electrical purposes
Part 2: Methods of test
(IEC 61212-2:2006)


Matériaux isolants -  Isolierstoffe -
Tubes et barres industriels, rigides, Runde Rohre und Stäbe aus
ronds, stratifiés, à base de résines technischen Schichtpressstoffen
thermodurcissables, à usages électriques auf der Basis warmhärtender Harze
für elektrotechnische Zwecke
Partie 2: Méthodes d'essai
(CEI 61212-2:2006) Teil 2: Prüfverfahren
(IEC 61212-2:2006)




This European Standard was approved by CENELEC on 2006-11-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, the Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: rue de Stassart 35, B - 1050 Brussels


© 2006 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 61212-2:2006 E

---------------------- Page: 2 ----------------------

EN 61212-2:2006 - 2 -
Foreword
The text of document 15/273/FDIS, future edition 2 of IEC 61212-2, prepared by IEC TC 15, Solid
electrical insulating materials, was submitted to the IEC-CENELEC parallel vote and was approved by
CENELEC as EN 61212-2 on 2006-11-01.
This European Standard supersedes EN 61212-2:1996.
The main changes from EN 61212-2:1996 are as follows:
– added application use and safety statements;
– reformatted document to bring it up to current IEC document format;
– test method references updated.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
(dop) 2007-08-01
national standard or by endorsement
– latest date by which the national standards conflicting
(dow) 2009-11-01
with the EN have to be withdrawn
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 61212-2:2006 was approved by CENELEC as a European
Standard without any modification.
__________

---------------------- Page: 3 ----------------------

- 3 - EN 61212-2:2006
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications

The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indi
...